| Detection Item | Symptom | Trouble Area |
|---|---|---|
| Hybrid Vehicle Control ECU Communication Stop Mode | Any of the following conditions are met:
·
·
|
·
Hybrid vehicle control ECU branch line or connector ·
Power source circuit of hybrid vehicle control ECU ·
Hybrid vehicle control ECU ground circuit ·
Hybrid vehicle control ECU |
for LHD
for RHD
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Inspect the fuses for circuits related to this system before performing the following procedure.
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more.
Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| for 2ZR-FXE | A |
| for M20A-FXS | B |
A
B
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the hybrid vehicle control ECU connector.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F3-25 (CA1H) - F3-24 (CA1L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F3-31 (CA3P) - F3-30 (CA3N) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the hybrid vehicle control ECU connectors.
Reconnect the cable to the negative (-) auxiliary battery terminal.
Measure the voltage according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
- | - |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F3-3 (BATT) - Body ground | Power switch off | 11 to 14 V |
| A49-3 (IG2) - Body ground | Power switch on (IG) | 11 to 14 V |
| Result |
|---|
| OK |
| NG |
OK
NG
Check the ECU power source circuit.
for LITHIUM-ION BATTERY: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>ECU Power Source Circuit
for NICKEL METAL HYDRIDE BATTERY: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>ECU Power Source Circuit
| Result |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the hybrid vehicle control ECU connector.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F160-21 (CA1H) - F160-8 (CA1L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F160-7 (CA3P) - F160-20 (CA3N) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the hybrid vehicle control ECU connectors.
Reconnect the cable to the negative (-) auxiliary battery terminal.
Measure the voltage according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
- | - |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F160-27 (BATT) - Body ground | Power switch off | 11 to 14 V |
| F160-35 (IG2) - Body ground | Power switch on (IG) | 11 to 14 V |
| Result |
|---|
| OK |
| NG |
OK
NG
Check the ECU power source circuit.
| Result |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
NG