Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P003373  Turbocharger / Supercharger Bypass Valve "A" Control Actuator Stuck Closed  


DESCRIPTION

Refer to DTC P003312.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P003312

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P003373 Turbocharger / Supercharger Bypass Valve "A" Control Actuator Stuck Closed The boost pressure does not drop despite control to open the air by-pass valve being commanded (1 trip detection logic).
·

Turbocharger sub-assembly (air by-pass valve)

·

No. 1 turbo pressure sensor

·

Wire harness or connector

·

ECM


Does not come on DTC stored SAE Code: P0039

MONITOR DESCRIPTION

If the throttle valve is closed while boost pressure is being applied, the air by-pass valve opens and the excess pressure between the turbocharger and the throttle valve is released. If the boost pressure does not drop for a certain amount of time despite control to open the air by-pass valve being commanded, the ECM determines that the air by-pass valve is stuck closed and stores this DTC.

CONFIRMATION DRIVING PATTERN

A330723E19
4.448,0.958 4.802,0.667 4.802,0.667 5.021,0.667 false 3.042,1.854 2.635,1.344 2.635,1.344 2.438,1.344 false 0.25,0.292 1.354,0.542 1.104,0.25 10 false Vehicle Speed 0.177,0.677 1.385,0.969 1.208,0.292 10 false 50 km/h (31 mph) 0.927,2.042 1.542,2.24 0.615,0.198 10 false Idling 0.396,2.365 1.313,2.75 0.917,0.385 10 false Ignition switch ON 5.625,3.375 5.99,3.625 0.365,0.25 10 false [D] 1.427,1.26 2.729,1.563 1.302,0.302 10 false Fully depressed 5.083,0.604 6.031,0.792 0.948,0.188 10 false Released 2.198,1.885 2.656,2.083 0.458,0.198 10 false [A] 3.125,1.417 3.604,1.615 0.479,0.198 10 false [B] 4.906,1.406 5.365,1.604 0.458,0.198 10 false [C]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

9.

Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Quickly release the accelerator pedal from the fully depressed position [C].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




WIRING DIAGRAM

·

Refer to DTC P003312 for air by-pass valve circuit.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P003312

·

Refer to DTC P023511 for No. 1 turbo pressure sensor circuit.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P023511


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P003373)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

Result:
Result Proceed to
DTC P003373 is output A
DTC P003373 and other DTCs are output B


HINT:

If any DTCs other than P003373 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR BYPASS VALVE)

B

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR BYPASS VALVE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Air Bypass Valve / Data List / All Data / Air Bypass Valve Control.

Powertrain > Engine > Active Test
Active Test Display
Activate the Air Bypass Valve
Data List Display
Air Bypass Valve Control
50004 372 12 282

e.

According to the display on the GTS, perform the Active Test and check the operation and operation sound of the air by-pass valve.

OK:
Active Test Standard
ON
·

ON is displayed for Data List item "Air Bypass Valve Control"

·

Air by-pass valve operates (operation sound is normal)





Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 1 TURBO PRESSURE SENSOR

NG

8.INSPECT AIR BY-PASS VALVE
3.INSPECT NO. 1 TURBO PRESSURE SENSOR

Result:
Proceed to
OK
NG



OK

11.CHECK WHETHER DTC OUTPUT RECURS (P003373)

NG

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 TURBO PRESSURE SENSOR)
4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 TURBO PRESSURE SENSOR)
A347474C31
0.25,1.948 0.688,2.219 0.438,0.271 1.083,2.792 1.271,2.281 true 1.615,2.813 1.594,2.302 true 2.156,2.813 1.906,2.302 true 0.188,0.177 0.646,0.375 0.458,0.198 10 false *a 0.375,2.01 0.833,2.208 0.458,0.198 10 false C3 0.948,2.844 1.406,3.042 0.458,0.198 10 false PIM 1.542,2.844 2,3.042 0.458,0.198 10 false E2 2.104,2.844 2.563,3.042 0.458,0.198 10 false VC
*a Front view of wire harness connector
(to No. 1 Turbo Pressure Sensor)


a.

Disconnect the No. 1 turbo pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C3-3 (VC) - C3-2 (E2) Ignition switch ON 4.75 to 5.25 V
C3-1 (PIM) - C3-2 (E2) Ignition switch ON 3.0 to 5.25 V



Result:
Proceed to
OK
NG



OK

5.REPLACE NO. 1 TURBO PRESSURE SENSOR

NG

7.CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)
5.REPLACE NO. 1 TURBO PRESSURE SENSOR

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (P003373)
6.CHECK WHETHER DTC OUTPUT RECURS (P003373)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTC.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

k.

Read the DTCs.


Result:
Result Proceed to
DTC P003373 is output A
DTCs are not output B



A

8.INSPECT AIR BY-PASS VALVE

B

END

7.CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the C3 No. 1 turbo pressure sensor connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C3-3 (VC) - C62-140 (VPTA) Always Below 1 Ω
C3-2 (E2) - C62-139 (EPTA) Always Below 1 Ω
C3-1 (PIM) - C62-108 (PTA) Always Below 1 Ω
C3-3 (VC) or C62-140 (VPTA) - Body ground and other terminals Always 10 kΩ or higher
C3-1 (PIM) or C62-108 (PTA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT AIR BY-PASS VALVE

Result:
Proceed to
OK
NG



OK

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR BY-PASS VALVE)

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY (AIR BY-PASS VALVE MALFUNCTION)

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR BY-PASS VALVE)
A346377C18
0.594,2.229 1,2.531 0.406,0.302 1,3 1.583,2.5 true 0.24,0.198 0.552,0.396 0.313,0.198 10 false *a 0.688,2.292 1.24,2.563 0.552,0.271 10 false C53 0.833,3 1.146,3.198 0.313,0.198 10 false +B
*a Front view of wire harness connector (to Air By-pass Valve)


a.

Disconnect the air by-pass valve connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C53-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE - ECM)

NG

10.CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE - ECM)
a.

Disconnect the C53 air by-pass valve connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C53-2 (ABV) - C62-67 (ABV) Always Below 1 Ω
C53-2 (ABV) or C62-67 (ABV) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

11.CHECK WHETHER DTC OUTPUT RECURS (P003373)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK WHETHER DTC OUTPUT RECURS (P003373)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTC.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

k.

Read the DTCs.


Result:
Result Proceed to
DTC P003373 is output A
DTCs are not output B



A

B