Refer to DTC P003312.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P003312
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P023400 | Turbocharger/Supercharger "A" Overboost Condition | Either of the following conditions is met (1 trip detection logic):
·
Boost pressure exceeds the threshold value (calculated from turbocharger speed upper limit value). ·
Boost pressure exceeds the threshold value (calculated from compressor downstream temperature upper limit value). |
·
Turbocharger sub-assembly (waste gate valve) ·
Turbocharger sub-assembly (waste gate valve actuator) ·
Vacuum regulating valve assembly ·
No. 1 turbo pressure sensor ·
Mass air flow meter ·
Wire harness or connector ·
ECM |
Does not come on | DTC stored | SAE Code: P0234 |
If the boost pressure exceeds the threshold value (calculated from turbocharger speed upper limit value or compressor downstream temperature upper limit value), there may be a malfunction in the turbocharger system. In this case, the ECM stores this DTC.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P023400.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.
Refer to DTC P010012 for the mass air flow meter circuit.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P010012
Refer to DTC P011011 for intake air temperature sensor (mass air flow meter) circuit.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P011011
Refer to DTC P023511 for No. 1 turbo pressure sensor circuit.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P023511
Refer to DTC P024313 for vacuum regulating valve assembly circuit.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P024313
Inspect the fuses for circuits related to this system before performing the following procedure.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P023400 is output | A |
| DTC P023400 and other DTCs are output | B |
If any DTCs other than P023400 are output, troubleshoot those DTCs first.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Atmospheric Pressure.
| Tester Display |
|---|
| Atmospheric Pressure |
Using the following table, determine the normal atmospheric pressure for the current altitude and temperature.
Standard atmospheric pressure is approximately 101 kPa(abs) (15 psi(abs)).
For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa (0.15 psi). This varies depending on the weather.
Compare the value of Atmospheric Pressure with the normal atmospheric pressure in the table.
| Result | Proceed to |
|---|---|
| Other than below | A |
| Difference between value of Atmospheric Pressure and normal atmospheric pressure is 10 kPa (1.45 psi) or higher. | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Air Temperature.
| Tester Display |
|---|
| Intake Air Temperature |
According to the display on the GTS, read the Data List.
| Result | Proceed to |
|---|---|
| Difference between value of Intake Air Temperature and actual ambient air temperature is 10°C (18°F) or higher. | A |
| Other than above | B |
A
B
Inspect the mass air flow meter, referring to On-vehicle Inspection for Mass Air Flow Meter.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>MASS AIR FLOW METER>ON-VEHICLE INSPECTION
Inspect the mass air flow meter, referring to Inspection for Mass Air Flow Meter.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION
Inspect the operation of the mass air flow meter.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Speed, Mass Air Flow Sensor and Coolant Temperature.
| Tester Display |
|---|
| Engine Speed |
| Mass Air Flow Sensor |
| Coolant Temperature |
Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.
Read Mass Air Flow Sensor while maintaining an engine speed of 3000 rpm.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Mass Air Flow Sensor | Shift lever position: P or N (neutral)
A/C switch: Off Engine Speed: 3000 rpm |
Between 4.0 gm/sec and 14.0 gm/sec |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 1 turbo pressure sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the vacuum regulating valve assembly.
Click hereEngine / Hybrid System>8NR-FTS (EMISSION CONTROL)>VACUUM REGULATING VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the turbocharger sub-assembly (waste gate valve).
Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>TURBOCHARGER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the turbocharger sub-assembly (waste gate valve actuator).
Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>TURBOCHARGER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C52 vacuum regulating valve assembly connector.
Disconnect the C62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C52-1 - C62-37 (WGV+) | Always | Below 1 Ω |
| C52-2 - C62-36 (WGV-) | Always | Below 1 Ω |
| C52-1 or C62-37 (WGV+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C52-2 or C62-36 (WGV-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and warm it up.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P023400.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P023400 is output) |
B |
A
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
B
| *a | Front view of wire harness connector
(to No. 1 Turbo Pressure Sensor) |
Disconnect the No. 1 turbo pressure sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C3-3 (VC) - C3-2 (E2) | Ignition switch ON | 4.75 to 5.25 V |
| C3-1 (PIM) - C3-2 (E2) | Ignition switch ON | 3.0 to 5.25 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C3 No. 1 turbo pressure sensor connector.
Disconnect the C62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C3-3 (VC) - C62-140 (VPTA) | Always | Below 1 Ω |
| C3-2 (E2) - C62-139 (EPTA) | Always | Below 1 Ω |
| C3-1 (PIM) - C62-108 (PTA) | Always | Below 1 Ω |
| C3-3 (VC) or C62-140 (VPTA) - Body ground and other terminals | Always | 10 kΩ or higher |
| C3-1 (PIM) or C62-108 (PTA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Mass Air Flow Meter) |
Disconnect the mass air flow meter connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C6-1 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C6 mass air flow meter connector.
Disconnect the C62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C6-3 (VG) - C62-92 (VG) | Always | Below 1 Ω |
| C6-2 (E2G) - C62-91 (E2G) | Always | Below 1 Ω |
| C6-3 (VG) or C62-92 (VG) - Body ground and other terminals | Always | 10 kΩ or higher |
Perform "Inspection After Repair" after replacing the mass air flow meter.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the mass air flow meter (intake air temperature sensor).
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION
Perform "Inspection After Repair" after replacing the mass air flow meter.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C6 mass air flow meter connector.
Disconnect the C62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C6-4 (THA) - C62-94 (THA) | Always | Below 1 Ω |
| C6-5 (E2) - C62-93 (ETHA) | Always | Below 1 Ω |
| C6-4 (THA) or C62-94 (THA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG