The fuel trim is related to the feedback compensation value, not to the basic injection duration. The fuel trim consists of both the short-term and long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P017100 | System Too Lean Bank 1 | With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic). | ·
Intake system ·
Fuel injector assembly ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Fuel pressure ·
Fuel delivery pipe (fuel pressure sensor) ·
Gas leak from exhaust system ·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
Purge VSV ·
PCV valve and system ·
Wire harness or connector ·
ECM |
Comes on (Euro-OBD) / - (Except Euro-OBD) | DTC stored (Euro-OBD) / - (Except Euro-OBD) | SAE Code:
P0171 |
| P017200 | System Too Rich Bank 1 | With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic). | ·
Intake system ·
Fuel injector assembly ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Ignition system ·
Fuel pressure ·
Fuel delivery pipe (fuel pressure sensor) ·
Gas leak from exhaust system ·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
Wire harness or connector ·
ECM |
Comes on (Euro-OBD) / - (Except Euro-OBD) | DTC stored (Euro-OBD) / - (Except Euro-OBD) | SAE Code:
P0172 |
When DTC P017100 is stored, the actual air fuel ratio is on the lean side. When DTC P017200 is stored, the actual air fuel ratio is on the rich side.
If the vehicle runs out of fuel, the air fuel ratio is lean and DTC P017100 may be stored. The MIL is then illuminated.
Under closed loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the fuel injection volumes estimated by the ECM also affect the average fuel trim learned value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learned value of the air fuel ratio). If the average fuel trim learned value exceeds the malfunction thresholds, the ECM interprets this as a fault in the fuel system and stores a DTC.
Example:
The average fuel trim learned value is +48% or higher, or -35% or less, the ECM interprets this as a fuel system malfunction.
| Required Sensors/Components | Air fuel ratio sensor
Mass air flow meter Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Fuel system status | Closed loop |
| Battery voltage | 11 V or higher |
| Either of the following conditions is met | 1 or 2 |
| 1. Engine speed | Less than 1100 rpm |
| 2. Engine load | 10% or higher |
| EVAP purge-cut | Executing |
| Either of the following conditions is met | 1 or 2 |
| 1. Average between short-term fuel trim and long-term fuel trim | 48% or higher (varies with engine coolant temperature) |
| 2. Average between short-term fuel trim and long-term fuel trim | -35% or less (varies with engine coolant temperature) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on [A].
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].
With the engine warmed up, idle the engine for 2 minutes or more [C].
Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for 5 minutes or more [D].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine / Trouble Codes [E].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
Refer to DTC P010012 for the mass air flow meter circuit.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P010012
Refer to DTC P044313 for purge VSV circuit.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P044313
Refer to DTC P003012 for the air fuel ratio sensor circuit.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P003012
Inspect the fuses for circuits related to this system before performing the following procedure.
A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P017100 or P017200 is output | A |
| DTC P017100 and/or P017200 and other DTCs are output | B |
If any DTCs other than P017100 or P017200 are output, troubleshoot those DTCs first.
A
B
Inspect the purge VSV.
Click hereEngine / Hybrid System>8NR-FTS (EMISSION CONTROL)>PURGE VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C12 purge VSV connector.
Disconnect the C62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C12-2 - C62-70 (PRG) | Always | Below 1 Ω |
| C12-2 or C62-70 (PRG) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Before inspecting the PCV valve, first check that there is no suction from the air hole cover.
No suction from air hole cover, and PCV valve operation is normal.
Check PCV valve.
Click hereEngine / Hybrid System>8NR-FTS (EMISSION CONTROL)>PCV VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks in intake system.
If a malfunction is detected while the brake pedal is being depressed, vacuum leaks in the brake booster assembly are suspected. Inspect the brake booster assembly.
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.
| Active Test Display |
|---|
| Control the Injection Volume for A/F Sensor |
| Data List Display |
|---|
| A/F (O2) Sensor Voltage B1S1 |
| O2 Sensor Voltage B1S2 |
Perform the Control the Injection Volume for A/F Sensor for operation with the engine idling (change the fuel injection volume).
Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2) displayed on the GTS.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
| GTS Display (Sensor) | Injection Volume | Status | Voltage |
|---|---|---|---|
| A/F (O2) Sensor Voltage B1S1
(Air fuel ratio) |
12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2 Sensor Voltage B1S2
(Heated oxygen) |
12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status of A/F (O2) Sensor Voltage B1S1 | Status of O2 Sensor Voltage B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Suspected Trouble Area | Proceed to |
|---|---|---|---|---|
| Lean/Rich | Lean/Rich | Normal | - | A |
| Lean | Lean | Actual air fuel ratio lean | ·
PCV valve and system ·
Gas leak from exhaust system ·
Intake system ·
Fuel pressure ·
Mass air flow meter ·
Engine coolant temperature sensor |
|
| Rich | Rich | Actual air fuel ratio rich | ·
Gas leak from exhaust system ·
Ignition system ·
Fuel pressure ·
Mass air flow meter ·
Engine coolant temperature sensor |
|
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | ·
Air fuel ratio sensor |
B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | ·
Air fuel ratio sensor |
Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (A/F (O2) Sensor Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2 Sensor Voltage B1S2) is consistently below 0.4 V.
Rich: During Control the Injection Volume for A/F Sensor, the A/F (O2) Sensor Voltage B1S1 is consistently below 3.1 V, and the O2 Sensor Voltage B1S2 is consistently higher than 0.55 V.
Lean/Rich: During Control the Injection Volume for A/F Sensor, the output voltage of the air fuel ratio sensor or heated oxygen sensor alternates correctly.
Refer to "Data List / Active Test" [A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2].
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temperature.
| Tester Display |
|---|
| Coolant Temperature |
Read the Data List twice, when the engine is both cold and warmed up.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Coolant Temperature | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Speed, Mass Air Flow Sensor and Coolant Temperature.
| Tester Display |
|---|
| Engine Speed |
| Mass Air Flow Sensor |
| Coolant Temperature |
Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.
Read Mass Air Flow Sensor with the engine speed at 3000 rpm.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Mass Air Flow Sensor | Shift lever position: P or N (neutral)
A/C: Off Engine Speed: 3000 rpm |
Between 4.0 gm/sec and 14.0 gm/sec |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel pressure (for low pressure side).
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine / Data List / All Data / Fuel Pressure (High).
| Tester Display |
|---|
| Fuel Pressure (High) |
Read the values.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Fuel Pressure (High) | Shift lever position: P or N (neutral)
A/C: Off Engine idling |
4000 to 18000 kPag |
| Shift lever position: P or N (neutral)
A/C: Off Engine speed: 3000 rpm |
8000 to 18000 kPag |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for exhaust gas leaks.
No gas leaks.
Perform "Inspection After Repair" after repairing or replacing the exhaust system.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a spark test.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after repairing or replacing the ignition system.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Check the resistance of the fuel injector assembly.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL INJECTOR>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel pump operation (for low pressure side).
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the air fuel ratio sensor.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C25 air fuel ratio sensor connector.
Disconnect the C62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C25-1 (HA1A) - C62-19 (HA1A) | Always | Below 1 Ω |
| C25-3 (A1A+) - C62-131 (A1A+) | Always | Below 1 Ω |
| C25-4 (A1A-) - C62-132 (A1A-) | Always | Below 1 Ω |
| C25-1 (HA1A) or C62-19 (HA1A) - Body ground and other terminals | Always | 10 kΩ or higher |
| C25-3 (A1A+) or C62-131 (A1A+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C25-4 (A1A-) or C62-132 (A1A-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air fuel ratio sensor.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P017100 and/or P017200 are output | A |
| DTCs are not output | B |
A
B
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM.
Repair any problems.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P017100 and/or P017200 are output | A |
| DTCs are not output | B |
A
B
Disconnect the C6 mass air flow meter connector.
Disconnect the C62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C6-3 (VG) - C62-92 (VG) | Always | Below 1 Ω |
| C6-2 (E2G) - C62-91 (E2G) | Always | Below 1 Ω |
| C6-3 (VG) or C62-92 (VG) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the mass air flow meter.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL
If the result of the inspection performed in step 8 indicated no problem, proceed to the next step without replacing the mass air flow meter.
Perform "Inspection After Repair" after replacing the mass air flow meter.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P017100 and/or P017200 are output | A |
| DTCs are not output | B |
A
B