Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2018.05
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P030000  Random/Multiple Cylinder Misfire Detected  P030027  Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold  P030085  Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range  P030100  Cylinder 1 Misfire Detected  P030200  Cylinder 2 Misfire Detected  P030300  Cylinder 3 Misfire Detected  P030400  Cylinder 4 Misfire Detected  


DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P030000 Random/Multiple Cylinder Misfire Detected Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Spark plug

·

Fuel injector assembly

·

Fuel pressure

·

Fuel pump assembly (for high pressure side)

·

Fuel line

·

Fuel pump (for low pressure side)

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and system

·

Intake system

·

ECM


Comes on/Blinks* (Euro-OBD) / - (Except Euro-OBD)
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD) / - (Except Euro-OBD) SAE Code:
P0300
P030027 Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold An emission deterioration misfire occurs (2 trip detection logic).
·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Spark plug

·

Fuel injector assembly

·

Fuel pressure

·

Fuel pump assembly (for high pressure side)

·

Fuel line

·

Fuel pump (for low pressure side)

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and system

·

Intake system

·

ECM


Comes on (Euro-OBD) / - (Except Euro-OBD) DTC stored (Euro-OBD) / - (Except Euro-OBD) SAE Code:
-
P030085 Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range A misfire occurs that may damage the three-way catalytic converter (2 trip detection logic).
·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Spark plug

·

Fuel injector assembly

·

Fuel pressure

·

Fuel pump assembly (for high pressure side)

·

Fuel line

·

Fuel pump (for low pressure side)

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and system

·

Intake system

·

ECM


Comes on/Blinks* (Euro-OBD) / - (Except Euro-OBD)
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD) / - (Except Euro-OBD) SAE Code:
-
P030100 Cylinder 1 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Spark plug

·

Fuel injector assembly

·

Fuel pressure

·

Fuel pump assembly (for high pressure side)

·

Fuel line

·

Fuel pump (for low pressure side)

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and system

·

Intake system

·

ECM


Comes on/Blinks* (Euro-OBD) / - (Except Euro-OBD)
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD) / - (Except Euro-OBD) SAE Code:
P0301
P030200 Cylinder 2 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Spark plug

·

Fuel injector assembly

·

Fuel pressure

·

Fuel pump assembly (for high pressure side)

·

Fuel line

·

Fuel pump (for low pressure side)

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and system

·

Intake system

·

ECM


Comes on/Blinks* (Euro-OBD) / - (Except Euro-OBD)
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD) / - (Except Euro-OBD) SAE Code:
P0302
P030300 Cylinder 3 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Spark plug

·

Fuel injector assembly

·

Fuel pressure

·

Fuel pump assembly (for high pressure side)

·

Fuel line

·

Fuel pump (for low pressure side)

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and system

·

Intake system

·

ECM


Comes on/Blinks* (Euro-OBD) / - (Except Euro-OBD)
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD) / - (Except Euro-OBD) SAE Code:
P0303
P030400 Cylinder 4 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Spark plug

·

Fuel injector assembly

·

Fuel pressure

·

Fuel pump assembly (for high pressure side)

·

Fuel line

·

Fuel pump (for low pressure side)

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and system

·

Intake system

·

ECM


Comes on/Blinks* (Euro-OBD) / - (Except Euro-OBD)
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD) / - (Except Euro-OBD) SAE Code:
P0304

When DTCs for misfiring cylinders are randomly stored, but DTC P030000 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P030000 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when the following condition, which could cause emission deterioration, is detected (2 trip detection logic).

·

An excessive number of misfires (approximately 68 to 80 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.


The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when the following condition, which could cause damage to the three-way catalytic converter, is detected.

·

In every 200 crankshaft revolutions, the threshold misfiring percentage is recorded 3 times.


MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Camshaft position sensor
Required Sensors/Components (Related) Engine coolant temperature
Intake air temperature sensor (mass air flow meter)
Mass air flow meter
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Misfire
Either of the following conditions is met (a) or (b)
(a) Engine coolant temperature at engine start Higher than -7°C (19°F)
(b) Engine coolant temperature Higher than 20°C (68°F)

Monitor Period of Emission-related Misfire
Duration Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-damaging Misfire (MIL Blinks)
Duration Crankshaft 200 revolutions x 3

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Record the DTC(s) and freeze frame data.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Using the GTS, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE

7.

Start the engine.

8.

Read the misfire counts of each cylinder, Misfire Count Cylinder #1 to Misfire Count Cylinder #4, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.

9.

Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.

HINT:

In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.

Engine speed Duration
Idling 8 minutes or more
1000 4.5 minutes or more
2000 2.5 minutes or more
3000 1.5 minutes or more


10.

Check whether misfires have occurred by checking DTCs and freeze frame data.

HINT:

Do not turn the ignition switch off until the output DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.


11.

Record the DTC(s), freeze frame data and misfire counts.

12.

Turn the ignition switch off and wait for at least 30 seconds.

13.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).


WIRING DIAGRAM

Refer to DTC P010012 for the mass air flow meter circuit.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P010012

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

Check the "Fuel Cut Elapsed Time" in the Data List or the Freeze Frame Data.

If the elapsed time is over 0 seconds, then the engine speed is high (engine speed at which fuel cut occurs + 500 rpm).

When this has happened, there is the possibility that the No. 1 valve rocker arm sub-assembly will become loose and a fire could start, so check that the No. 1 valve rocker arm sub-assembly is properly attached.

·

By clearing the DTCs, "Fuel Cut Elapsed Time" will be cleared.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.

·

If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:

(a)

There was insufficient fuel in the tank.

(b)

Improper fuel was used.

(c)

The spark plugs have been contaminated.

(d)

The problem requires further diagnosis.


·

After finishing repairs, check the misfire counts of the cylinders (Misfire Count Cylinder #1 to Misfire Count Cylinder #4).

·

Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.

·

When one of Short FT Bank 1 or Long FT Bank 1 in the freeze frame data is outside the range of +/-20%, the air fuel ratio may be rich (-20% or less) or lean (+20% or higher).

·

When Coolant Temperature in the freeze frame data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.

·

Vehicle body vibration caused by an extremely imbalanced drive wheel may cause misfire DTCs to be stored.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

In the past, when the primary ignition system (the igniter drive circuit in the ECM, the primary circuit in the No. 1 ignition coil, the related wire harness, or the connector) was out of order, diagnostic codes from P035113, P035213, P035313 and P035413 were output. However, these codes are not output in this vehicle.

When a failure in the primary ignition system is suspected, refer to "Catalyst OT Misfire Fuel Cut History", "Catalyst OT Misfire Fuel Cut Cylinder #1 to #4", and "Misfire Count Cylinder #1 to Misfire Count Cylinder #4" in the freeze frame data, the pending freeze frame data, and the Data List, and confirm in which cylinder the high-frequency misfire was concentrated.

·

Referring to the following contents of the freeze frame data (or the pending freeze frame data) enables an estimation of which cylinder has misfired and to what degree.

-

Misfire Count Cylinder #1 to Misfire Count Cylinder #4: Misfire count according to cylinder.

-

Catalyst OT Misfire Fuel Cut Cylinder #1 to #4: This expresses a high-frequency misfire was concentrated in a certain cylinder and that cylinder's fuel injection was stopped.




PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

Result:
Result Proceed to
DTC P030000, P030027, P030085, P030100, P030200, P030300 and/or P030400 are output A
DTC P030000, P030027, P030085, P030100, P030200, P030300 and/or P030400 and other DTCs are output B


HINT:

If any DTCs other than P030000, P030027, P030085, P030100, P030200, P030300 and/or P030400 are output, troubleshoot those DTCs first.




A

2.CHECK PCV VALVE

B

2.CHECK PCV VALVE
a.
A384855

Before inspecting the PCV valve, first check that there is no suction from the air hole cover.

OK:

No suction from air hole cover, and PCV valve operation is normal.




Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Misfire RPM and Misfire Load.

Powertrain > Engine > Data List
Tester Display
Misfire RPM
Misfire Load
50003 372 146,152

e.

Read and note the Misfire RPM and Misfire Load values.

HINT:

The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.



Result:
Proceed to
NEXT



NEXT

4.READ FREEZE FRAME DATA (CATALYST OT MISFIRE FUEL CUT HISTORY)
4.READ FREEZE FRAME DATA (CATALYST OT MISFIRE FUEL CUT HISTORY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Proceed to
Catalyst OT Misfire Fuel Cut History ON A
OFF B



A

5.INSPECT SPARK PLUG

B

8.PERFORM ACTIVE TEST USING GTS (PROHIBIT THE CATALYST OT MISFIRE PREVENT FUEL CUT)
5.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

According to the "Cat OT MF F/C History and Cat OT MF F/C Cylinder #1 to #4" on the Data List, check the spark plug of the malfunctioning cylinder.

·

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

6.CHECK FOR SPARK (IGNITION COIL ASSEMBLY, SPARK PLUG)

NG

6.CHECK FOR SPARK (IGNITION COIL ASSEMBLY, SPARK PLUG)
a.

Interchange both the ignition coil assembly and spark plug and perform a spark test.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after replacing the ignition coil assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

7.READ VALUE USING GTS (CATALYST OT MISFIRE FUEL CUT)
7.READ VALUE USING GTS (CATALYST OT MISFIRE FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Catalyst OT Misfire Fuel Cut.

Powertrain > Engine > Data List
Tester Display
Catalyst OT Misfire Fuel Cut
50003 372 154

e.

Read the value displayed on the GTS.

Result:
Data List Result Proceed to
Catalyst OT Misfire Fuel Cut Avail A
Not Avl B




A

8.PERFORM ACTIVE TEST USING GTS (PROHIBIT THE CATALYST OT MISFIRE PREVENT FUEL CUT)

B

9.READ VALUE USING GTS (MISFIRE COUNT CYLINDER)
8.PERFORM ACTIVE TEST USING GTS (PROHIBIT THE CATALYST OT MISFIRE PREVENT FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Prohibit the Catalyst OT Misfire Prevent Fuel Cut.

Powertrain > Engine > Active Test
Tester Display
Prohibit the Catalyst OT Misfire Prevent Fuel Cut
50004 372 42003

e.

Perform the Active Test.

NOTICE:

When performing the Active Test, make sure the vehicle is stopped and the engine is either idling or being revved within 3000 rpm.



Result:
Proceed to
NEXT



NEXT

9.READ VALUE USING GTS (MISFIRE COUNT CYLINDER)
9.READ VALUE USING GTS (MISFIRE COUNT CYLINDER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Misfire Count Cylinder #1 to Misfire Count Cylinder #4.

Powertrain > Engine > Data List
Tester Display
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
50003 372 148,149,150,151

e.

Start the engine and allow the engine to idle.


f.

Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #4 displayed on the GTS. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.

i.

Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using GTS (Misfire RPM and Misfire Load)" procedures above [A].


ii.

Read the Misfire Count Cylinder #1 to Misfire Count Cylinder #4 or DTCs displayed on the GTS [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.

·

If the freeze frame data record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.

·

If the freeze frame data record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.





Result:
Misfire Count Proceed to
1 or 2 cylinders have misfire counts A
3 cylinders or more have misfire counts B



A

10.INSPECT SPARK PLUG

B

21.CHECK INTAKE SYSTEM
10.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

11.CHECK FOR SPARK (IGNITION COIL ASSEMBLY, SPARK PLUG)

NG

11.CHECK FOR SPARK (IGNITION COIL ASSEMBLY, SPARK PLUG)
a.

Interchange both the ignition coil assembly and spark plug and perform a spark test.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after replacing the ignition coil assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

12.INSPECT FUEL INJECTOR ASSEMBLY
12.INSPECT FUEL INJECTOR ASSEMBLY
a.

Check the resistance of the fuel injector assembly.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

13.CHECK CYLINDER COMPRESSION PRESSURE

NG

REPLACE FUEL INJECTOR ASSEMBLY

13.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

14.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

14.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)
a.

Check the fuel pressure (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

15.READ VALUE USING GTS (FUEL PRESSURE (HIGH))

NG

37.CHECK FURL PUMP OPERATION (FOR LOW PRESSURE SIDE)
15.READ VALUE USING GTS (FUEL PRESSURE (HIGH))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine and warm it up.


e.

Enter the following menus: Powertrain / Engine / Data List / All Data / Fuel Pressure (High).

Powertrain > Engine > Data List
Tester Display
Fuel Pressure (High)
50003 372 265

f.

Read the values.

Standard:
GTS Display Condition Specified Condition
Fuel Pressure (High) Shift lever position: P or N (neutral)
A/C: Off
Engine idling
4000 to 18000 kPag
Shift lever position: P or N (neutral)
A/C: Off
Engine speed: 3000 rpm
8000 to 18000 kPag



Result:
Proceed to
OK
NG



OK

16.CHECK INTAKE SYSTEM

NG

CHECK AND REPLACE FUEL SYSTEM (FOR HIGH PRESSURE SIDE)

16.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

17.READ VALUE USING GTS (COOLANT TEMPERATURE)

NG

REPAIR OR REPLACE INTAKE SYSTEM

17.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temperature.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205

e.

Read the Data List twice, when the engine is both cold and warmed up.

Standard:
GTS Display Condition Specified Condition
Coolant Temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

18.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

NG

18.READ VALUE USING GTS (MASS AIR FLOW SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Speed, Mass Air Flow Sensor and Coolant Temperature.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Mass Air Flow Sensor
Coolant Temperature
50003 372 211,215,205

f.

Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.


g.

Read Mass Air Flow Sensor with the engine speed at 3000 rpm.

Standard:
GTS Display Condition Specified Condition
Mass Air Flow Sensor Shift lever position: P or N (neutral)
A/C: Off
Engine Speed: 3000 rpm
Between 4.0 gm/sec and 14.0 gm/sec



Result:
Proceed to
OK
NG



OK

19.CHECK ENGINE MECHANICAL SYSTEM

NG

32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
19.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY


Result:
Proceed to
OK
NG



OK

20.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

20.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

j.

Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300 or P030400.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P030000, P030027, P030085, P030100, P030200, P030300 and/or P030400 are output)
B




A

B

32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
21.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

22.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)

NG

REPAIR OR REPLACE INTAKE SYSTEM

22.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)
a.

Check the fuel pressure (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

23.READ VALUE USING GTS (FUEL PRESSURE (HIGH))

NG

37.CHECK FURL PUMP OPERATION (FOR LOW PRESSURE SIDE)
23.READ VALUE USING GTS (FUEL PRESSURE (HIGH))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine and warm it up.


e.

Enter the following menus: Powertrain / Engine / Data List / All Data / Fuel Pressure (High).

Powertrain > Engine > Data List
Tester Display
Fuel Pressure (High)
50003 372 265

f.

Read the values.

Standard:
GTS Display Condition Specified Condition
Fuel Pressure (High) Shift lever position: P or N (neutral)
A/C: Off
Engine idling
4000 to 18000 kPag
Shift lever position: P or N (neutral)
A/C: Off
Engine speed: 3000 rpm
8000 to 18000 kPag



Result:
Proceed to
OK
NG



OK

24.READ VALUE USING GTS (COOLANT TEMPERATURE)

NG

CHECK AND REPLACE FUEL SYSTEM (FOR HIGH PRESSURE SIDE)

24.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temperature.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205

e.

Read the Data List twice, when the engine is both cold and warmed up.

Standard:
GTS Display Condition Specified Condition
Coolant Temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

25.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

NG

25.READ VALUE USING GTS (MASS AIR FLOW SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Speed, Mass Air Flow Sensor and Coolant Temperature.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Mass Air Flow Sensor
Coolant Temperature
50003 372 211,215,205

f.

Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.


g.

Read Mass Air Flow Sensor with the engine speed at 3000 rpm.

Standard:
GTS Display Condition Specified Condition
Mass Air Flow Sensor Shift lever position: P or N (neutral)
A/C: Off
Engine Speed: 3000 rpm
Between 4.0 gm/sec and 14.0 gm/sec



Result:
Proceed to
OK
NG



OK

26.INSPECT SPARK PLUG

NG

32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
26.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

27.CHECK FOR SPARK (IGNITION COIL ASSEMBLY, SPARK PLUG)

NG

27.CHECK FOR SPARK (IGNITION COIL ASSEMBLY, SPARK PLUG)
a.

Interchange both the ignition coil assembly and spark plug and perform a spark test.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after replacing the ignition coil assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

28.CHECK CYLINDER COMPRESSION PRESSURE
28.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

29.INSPECT FUEL INJECTOR ASSEMBLY

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

29.INSPECT FUEL INJECTOR ASSEMBLY
a.

Check the resistance of the fuel injector assembly.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

30.CHECK ENGINE MECHANICAL SYSTEM

NG

REPLACE FUEL INJECTOR ASSEMBLY

30.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY


Result:
Proceed to
OK
NG



OK

31.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

31.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

j.

Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300 or P030400.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P030000, P030027, P030085, P030100, P030200, P030300 and/or P030400 are output)
B




A

B

32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

Repair any problems.



Result:
Proceed to
NEXT



NEXT

33.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
33.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

j.

Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300 or P030400.


k.

Check the DTC judgment result.

Result:
Result Proceed to
ABNORMAL
(DTC P030000, P030027, P030085, P030100, P030200, P030300 and/or P030400 are output)
A
NORMAL
(DTCs are not output)
B




A

34.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

B

34.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the C6 mass air flow meter connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C6-3 (VG) - C62-92 (VG) Always Below 1 Ω
C6-2 (E2G) - C62-91 (E2G) Always Below 1 Ω
C6-3 (VG) or C62-92 (VG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

35.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

35.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:
·

If the results of the inspections performed in step 15 or 22 indicated no problem, proceed to the next step without replacing the mass air flow meter.

·

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

36.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
36.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

j.

Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300 or P030400.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P030000, P030027, P030085, P030100, P030200, P030300 and/or P030400 are output)
B




A

END

B

37.CHECK FURL PUMP OPERATION (FOR LOW PRESSURE SIDE)
a.

Check the fuel pump operation (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

CHECK AND REPLACE FUEL SYSTEM (PRESSURE REGULATOR, PIPE LINE AND FILTER)

NG