Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299014 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Engine does not Start  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift lever is in P*1 and the brake pedal*1 or clutch pedal*2 is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the shift lever in N*1 and the brake pedal*1 or clutch pedal*2 depressed.

*1: for CVT

*2: for Manual Transaxle


Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Engine does not start
Power Source Control
·

Stop Light Switch1

·

Steering Unlock Switch

·

Shift P Signal*1

·

Neutral SW/ Clutch SW

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Starter Request Signal

·

Power Supply Condition


Entry&Start
·

Immobiliser

·

Engine Start Request

·

S Code Check

·

L Code Check


Starting Control
·

Starter SW

·

Shift Position P or N*1

·

Ignition



*1: for CVT


WIRING DIAGRAM

E352016E01
0.229,0.156 1.927,0.417 1.698,0.26 12 false for Manual Transaxle: 0.635,0.792 0.875,1 0.24,0.208 10 false +B 0.99,1.354 1.396,1.542 0.406,0.188 10 false STAR 1.458,1.365 1.604,1.552 0.146,0.188 10 false 9 2.458,2.51 2.604,2.698 0.146,0.188 10 false 2 3.656,2.5 3.802,2.688 0.146,0.188 10 false 1 2.375,2.875 2.698,3.052 0.323,0.177 10 false A51 2.354,3.042 3.948,3.26 1.594,0.219 10 false Clutch Switch Assembly 5.625,1.135 5.938,1.323 0.313,0.188 10 false 23*1 5.625,1.344 5.958,1.542 0.333,0.198 10 false 57*2 6.042,1.354 6.458,1.531 0.417,0.177 10 false NSW 6.583,0.958 6.823,1.167 0.24,0.208 10 false +B 1,3.698 1.323,3.854 0.323,0.156 10 false STA 1.458,3.698 1.708,3.885 0.25,0.188 10 false 20 5.76,3.708 6.01,3.896 0.25,0.188 10 false 29 6.031,3.708 6.354,3.865 0.323,0.156 10 false STA 0.188,4.698 0.583,4.885 0.396,0.188 10 false M66 0.167,4.875 1.688,5.24 1.521,0.365 10 false Certification ECU (Smart Key ECU Assembly) 6.375,4.51 6.771,4.698 0.396,0.188 10 false A38 6.354,4.677 6.75,4.865 0.396,0.188 10 false ECM 1.74,5.948 1.979,6.125 0.24,0.177 10 false ST 2.063,5.521 2.24,5.698 0.177,0.177 10 false 2 2.635,5.521 2.813,5.698 0.177,0.177 10 false 5 2.063,6.365 2.24,6.542 0.177,0.177 10 false 1 2.625,6.365 2.802,6.542 0.177,0.177 10 false 3 3.833,5.604 4.01,5.781 0.177,0.177 10 false 1 3.833,5.792 3.969,5.99 0.135,0.198 10 false 1 4.021,5.594 4.375,5.781 0.354,0.188 10 false C34 4.031,5.781 4.385,5.969 0.354,0.188 10 false C35 4.385,5.583 4.563,5.76 0.177,0.177 10 false *3 4.385,5.76 4.563,5.938 0.177,0.177 10 false *4 5.156,5.948 5.292,6.146 0.135,0.198 10 false 1 5.073,6.146 5.427,6.333 0.354,0.188 10 false C67 3.802,6.719 4.969,6.927 1.167,0.208 10 false Starter Assembly 6.135,6.594 6.979,6.792 0.844,0.198 10 false from Battery 0.188,7.083 1.354,7.292 1.167,0.208 10 false *1: for 3ZR-FAE 0.198,7.396 1.365,7.604 1.167,0.208 10 false *2: for 8NR-FTS 1.531,7.083 2.865,7.333 1.333,0.25 10 false *3: for TMC Made 1.531,7.365 2.865,7.615 1.333,0.25 10 false *4: for TMMT Made 4.76,5.229 5.115,5.417 0.354,0.188 10 false ST

E352013E01
0.25,0.24 1.021,0.51 0.771,0.271 12 false for CVT: 0.51,0.969 0.823,1.167 0.313,0.198 10 false +B 6.49,1.125 6.802,1.323 0.313,0.198 10 false +B 0.865,1.531 1.292,1.698 0.427,0.167 10 false STAR 1.354,1.531 1.5,1.698 0.146,0.167 10 false 9 5.5,1.344 5.823,1.51 0.323,0.167 10 false 23*1 5.5,1.521 5.823,1.688 0.323,0.167 10 false 57*2 5.938,1.531 6.333,1.708 0.396,0.177 10 false NSW 3.885,2.094 4.104,2.26 0.219,0.167 10 false 4 3.781,2.354 3.948,2.521 0.167,0.167 10 false B 4.052,2.354 4.219,2.521 0.167,0.167 10 false L 3.5,2.615 3.667,2.781 0.167,0.167 10 false P 3.479,2.885 3.646,3.052 0.167,0.167 10 false N 4.167,3.146 4.313,3.313 0.146,0.167 10 false 9 4.313,2.375 4.688,2.573 0.375,0.198 10 false C36 4.281,2.573 5.615,2.938 1.333,0.365 10 false Park/Neutral Position Switch 5.656,3.656 5.885,3.833 0.229,0.177 10 false 29 5.938,3.656 6.302,3.823 0.365,0.167 10 false STA 0.896,3.667 1.26,3.833 0.365,0.167 10 false STA 1.344,3.656 1.573,3.833 0.229,0.177 10 false 20 0.063,4.583 0.417,4.792 0.354,0.208 10 false M66 0.052,4.76 1.594,5.146 1.542,0.385 10 false Certification ECU (Smart Key ECU Assembly) 6.26,4.573 6.615,4.781 0.354,0.208 10 false A38 6.229,4.74 6.583,4.948 0.354,0.208 10 false ECM 4.74,5.177 5.094,5.385 0.354,0.208 10 false ST 1.75,5.927 2.104,6.135 0.354,0.208 10 false ST 2.052,5.5 2.229,5.698 0.177,0.198 10 false 2 2.615,5.5 2.792,5.698 0.177,0.198 10 false 5 2.01,6.333 2.188,6.531 0.177,0.198 10 false 1 2.625,6.333 2.802,6.531 0.177,0.198 10 false 3 3.823,5.573 4,5.771 0.177,0.198 10 false 1 3.823,5.75 4,5.948 0.177,0.198 10 false 1 4.031,5.563 4.344,5.729 0.313,0.167 10 false C34 4.031,5.75 4.344,5.917 0.313,0.167 10 false C35 4.375,5.573 4.552,5.771 0.177,0.198 10 false *3 4.375,5.74 4.552,5.938 0.177,0.198 10 false *4 5.156,5.927 5.333,6.125 0.177,0.198 10 false 1 5.083,6.115 5.396,6.281 0.313,0.167 10 false C67 3.802,6.698 4.948,6.917 1.146,0.219 10 false Starter Assembly 6.104,6.563 6.938,6.802 0.833,0.24 10 false from Battery 0.177,7.042 1.323,7.26 1.146,0.219 10 false *1: for 3ZR-FAE 0.177,7.354 1.323,7.573 1.146,0.219 10 false *2: for 8NR-FTS 1.667,7.052 3.333,7.302 1.667,0.25 10 false *4: for TMMT Made 1.677,7.365 3.344,7.615 1.667,0.25 10 false *3: for TMC Made

E352015E03
0.281,0.177 1.75,0.417 1.469,0.24 12 false for CVT: 0.677,1.865 0.906,2.063 0.229,0.198 10 false IC 1.156,1.76 1.552,1.927 0.396,0.167 10 false STP1 1.604,1.76 1.833,1.958 0.229,0.198 10 false 25 0.302,2.615 0.698,2.823 0.396,0.208 10 false M67 0.292,2.781 1.854,3.24 1.563,0.458 10 false Certification ECU (Smart Key ECU Assembly) 3.323,1.792 3.469,1.958 0.146,0.167 10 false 3 3.542,1.792 3.771,1.958 0.229,0.167 10 false L 3.875,1.875 4.083,2.083 0.208,0.208 10 false IC 4.396,1.865 4.604,2.073 0.208,0.208 10 false B 4.208,2.156 4.625,2.365 0.417,0.208 10 false GND 3.24,2.479 3.656,2.688 0.417,0.208 10 false A45 3.208,2.667 5.042,2.917 1.833,0.25 10 false Stop Light Switch Assembly 4.625,1.76 4.771,1.927 0.146,0.167 10 false 7 4.615,2.063 4.76,2.229 0.146,0.167 10 false 2 5.083,2.031 5.5,2.24 0.417,0.208 10 false STOP 6.063,1.865 7.063,2.115 1,0.25 10 false from Battery 5.646,0.625 5.792,0.792 0.146,0.167 10 false 9 5.896,0.74 6.396,0.99 0.5,0.25 10 false STP 6.167,1.281 6.51,1.51 0.344,0.229 10 false A38 6.146,1.448 6.49,1.677 0.344,0.229 10 false ECM 3.552,3.354 3.781,3.521 0.229,0.167 10 false 42 3.885,3.458 4.302,3.625 0.417,0.167 10 false STP 3.823,3.844 4.135,4.094 0.313,0.25 10 false A42 3.813,3.99 5.344,4.365 1.531,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 3.656,4.604 3.885,4.771 0.229,0.167 10 false 4 3.896,4.729 4.313,4.896 0.417,0.167 10 false STP 3.604,5.104 3.917,5.354 0.313,0.25 10 false F19 3.594,5.281 5.823,5.615 2.229,0.333 10 false Shift Lock Control Unit Assembly*1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PRECAUTION

·

After completing repairs, confirm that the problem does not recur.



HINT:
·

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

·

If the engine switch is turned from on (IG) to on (ACC) with the shift lever in any position other than P, and then the shift lever is moved to P and the engine switch is pressed with the brake pedal depressed, the engine switch will turn off.*1

·

If the brake pedal is repeatedly depressed while the engine is stopped, the brake booster pressure will be released and the force required to depress the brake pedal to illuminate the stop lights will increase.*1

*1: for CVT


·

The certification ECU (smart key ECU assembly) stores the operation history of the entry and start system and it can be read using the GTS.



Body Electrical > Entry&Start > Utility
Tester Display
Operation History
50005 125 52
Radio Wave Interference (RF Signal Received)
Parameter Name Content
Operating Engine Switch / Key RF Signal Interference When the engine switch was operated, the electrical key transmitter sub-assembly could not be confirmed due to wave interference.

PROCEDURE

1.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Press a switch of the electrical key transmitter sub-assembly.

OK:

The electrical key transmitter sub-assembly LED illuminates.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (KEY LOW BATTERY)

NG

14.INSPECT TRANSMITTER BATTERY
2.READ VALUE USING GTS (KEY LOW BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Low Battery Transmitter battery depleted No or Yes No: Transmitter battery not depleted
Yes: Transmitter battery depleted
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
Body Electrical > Entry&Start > Data List
Tester Display
Key Low Battery
50003 125 23

Result:
Result Proceed to
"No" is displayed on the GTS screen A
"Yes" is displayed on the GTS screen B



A

3.CHECK ENGINE CRANK

B

3.CHECK ENGINE CRANK
a.

Get into the vehicle while carrying the electrical key transmitter.


b.

Move the shift lever to P.*1


c.

Depress the brake pedal*1 or clutch pedal*2.


d.

Press the engine switch and check that the engine cranks.


*1: for CVT

*2: for Manual Transaxle


Result:
Result Proceed to
Engine cranks, but there is no initial combustion or engine is difficult to start A
Engine does not cranks B



A

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

B

6.CHECK FOR DTC
4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A38 ECM connector.


c.

Disconnect the A51 clutch switch assembly connector.*1


d.

Disconnect the C36 park/neutral position switch connector.*2


e.

Remove the ST relay.


f.

Measure the resistance according to the value(s) in the table below.

*1: for Manual Transaxle

*2: for CVT


Standard Resistance:
Tester Connection Condition Specified Condition
M66-20 (STA) - A38-29 (STA) Always Below 1 Ω
M66-20 (STA) or A38-29 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK CONNECTOR CONNECTION CONDITION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CONNECTOR CONNECTION CONDITION
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Connect the M66 certification ECU (smart key ECU assembly) connector.


c.

Press the engine switch and check that the engine starts.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

CONNECT SECURELY

NG

6.CHECK FOR DTC
a.

Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Starting Control > Trouble Codes
50001 221
Body Electrical > Power Source Control > Trouble Codes
50001 223

Result:
Result Proceed to
DTCs are not output A
Entry and start system (for Start Function) DTCs are output B



A

7.CHECK ENGINE SWITCH CONDITION

B

7.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.*1


c.

With the brake pedal*1 or clutch pedal*2 released, check that pressing the engine switch causes the power source mode to change.


*1: for CVT

*2: for Manual Transaxle


Result:
Result Proceed to
Power source mode changes : Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) or on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D



A

8.READ VALUE USING GTS (STOP LIGHT SWITCH1, NEUTRAL SW/ CLUTCH SW)

B

C

D

8.READ VALUE USING GTS (STOP LIGHT SWITCH1, NEUTRAL SW/ CLUTCH SW)
a.

for CVT

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The item in the Data List changes when the brake pedal is depressed and released.




b.

for Manual Transaxle

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW State of clutch pedal OFF or ON OFF: Clutch pedal released
ON: Clutch pedal depressed
·

Use this item to help determine if the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6
OK:

The item in the Data List changes when the clutch pedal is depressed and released.




Result:
Result Proceed to
OK (for CVT) A
OK (for Manual Transaxle) B
NG (for CVT) C
NG (for Manual Transaxle) D



A

9.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)

B

10.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

C

33.INSPECT STOP LIGHT SWITCH ASSEMBLY

D

36.INSPECT CLUTCH SWITCH ASSEMBLY
9.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Shift position (P and N) OFF or ON OFF: Shift lever not in P or N
ON: Shift lever in P or N
·

Use this item to determine whether the park/neutral start switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral start switch assembly malfunction, "OFF" is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6
Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position P or N Park/neutral position switch status OFF or ON OFF: Shift lever in any position other than P or N
ON: Shift lever in P or N
When OFF is displayed, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Shift Position P or N
50003 221 2

OK:

The item in the Data List changes according to the shift position.


Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

31.INSPECT PARK/NEUTRAL POSITION SWITCH
10.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Engine start request signal status OFF or ON
for CVT

OFF: The engine switch is not pressed

ON: With the shift lever in P and the brake pedal depressed, the engine switch is pressed and held


for Manual Transaxle

OFF: The engine switch is not pressed

ON: With the clutch pedal depressed, the engine switch is pressed and held


·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the key warning light is illuminated in green on the combination meter assembly, and then press the engine switch.


OK:

The display changes in response to the operation of the engine switch.



Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (STARTER SW)

NG

29.CHECK STEERING LOCK SYSTEM
11.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Starting Control / Data List.


e.

Get into the vehicle while carrying the electrical key transmitter sub-assembly, move the shift lever to P*1, press the engine switch while depressing the brake pedal*1 or clutch pedal*2 and confirm that the Data List item changes.

*1: for CVT

*2: for Manual Transaxle


Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter operation request OFF or ON OFF: Starter operation not requested
ON: Starter operation requested
When OFF is displayed, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Starter SW
50003 221 1
OK:

The Data List item changes.



Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (STARTER RELAY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.READ VALUE USING GTS (STARTER RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Starting Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Relay Starter relay voltage monitor OFF or ON OFF: ST relay off
ON: ST relay on
When OFF is displayed the engine cannot be cranked.
Body Electrical > Starting Control > Data List
Tester Display
Starter Relay
50003 221 3

Result:
Proceed to
OK
NG



OK

13.CHECK CONNECTOR CONNECTION CONDITION

NG

15.INSPECT ST RELAY
13.CHECK CONNECTOR CONNECTION CONDITION
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Connect the M66 certification ECU (smart key ECU assembly) connector.


c.

Press the engine switch and check that the engine starts.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

CONNECT SECURELY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

14.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>INSPECTION

NOTICE:

Do not wrap the lead wire ground a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

15.INSPECT ST RELAY
a.

Remove the ST relay.



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)

NG

REPLACE ST RELAY

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)
a.
B424432C14
1.458,0.073 1.875,0.323 0.417,0.25 0.635,1.458 1.313,1.094 true 1.104,1.802 1.615,0.969 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.542,0.104 1.854,0.302 0.313,0.198 10 false M66 0.323,1.354 1.25,1.552 0.927,0.198 10 false STA 0.708,1.708 1.156,1.906 0.448,0.198 10 false STAR
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A38 ECM connector.


c.

Move the shift lever to P or N.*1

*1: for CVT



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M66-20 (STA) - Body ground 20°C (68°F) 101.69 to 153.84 Ω
M66-9 (STAR) - Body ground



Result:
Result Proceed to
OK A
NG (for CVT) B
NG (for Manual Transaxle) C



A

17.INSPECT STARTER ASSEMBLY

B

19.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)

C

24.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH SWITCH ASSEMBLY)
17.INSPECT STARTER ASSEMBLY
a.

Remove the starter assembly.




b.

Result:
Result Proceed to
OK A
NG (for 8NR-FTS with Valeo Made Cold Area Specification Vehicles) B
NG (for 8NR-FTS with Denso Made without Stop and Start System) C
NG (for 8NR-FTS with Valeo Made except Cold Area Specification Vehicles) D
NG (for 3ZR-FAE) E



A

18.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER AND ST RELAY)

B

C

D

E

18.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER AND ST RELAY)
a.

Remove the starter assembly from the vehicle to perform an inspection.




b.

Remove the ST relay.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C67-1 - Body ground Always 11 to 14 V
ST relay terminal 5 - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 3 - C34-1*1 Always Below 1 Ω
ST relay terminal 3 - C35-1*2 Always Below 1 Ω
ST relay terminal 3 or C34-1 - Body ground*1 Always 10 kΩ or higher
ST relay terminal 3 or C35-1 - Body ground*2 Always 10 kΩ or higher


*1: for TMC Made

*2: for TMMT Made



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the C36 park/neutral position switch connector.


c.

Disconnect the A38 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M66-9 (STAR) - C36-4 (B) Always Below 1 Ω
M66-9 (STAR) or C36-4 (B) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)
a.

Disconnect the C36 park/neutral position switch connector.


b.

Remove the ST relay.


c.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the A38 ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-9 (L) - ST relay terminal 2 Always Below 1 Ω
C36-9 (L) or ST relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A38 ECM connector.


c.

Disconnect the C36 park/neutral position switch connector.


d.

Remove the ST relay.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M66-20 (STA) - ST relay terminal 2 Always Below 1 Ω
M66-20 (STA) or ST relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

23.CHECK CONNECTOR CONNECTION CONDITION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK CONNECTOR CONNECTION CONDITION
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Connect the M66 certification ECU (smart key ECU assembly) connector.


c.

Press the engine switch and check that the engine starts.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

CONNECT SECURELY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

24.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH SWITCH ASSEMBLY)
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A51 clutch switch assembly connector.


c.

Disconnect the A38 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M66-9 (STAR) - A51-2 Always Below 1 Ω
M66-9 (STAR) or A51-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ST RELAY)
a.

Disconnect the A51 clutch switch assembly connector.


b.

Remove the ST relay.


c.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the A38 ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A51-1 - ST relay terminal 2 Always Below 1 Ω
A51-1 or ST relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

26.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A38 ECM connector.


c.

Remove the ST relay.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M66-20 (STA) - ST relay terminal 2 Always Below 1 Ω
M66-20 (STA) or ST relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

27.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

28.CHECK CONNECTOR CONNECTION CONDITION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK CONNECTOR CONNECTION CONDITION
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Connect the M66 certification ECU (smart key ECU assembly) connector.


c.

Press the engine switch and check that the engine starts.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

CONNECT SECURELY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

29.CHECK STEERING LOCK SYSTEM
a.

Check that the steering unlocks when the engine switch is turned on (ACC).

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

30.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER SYSTEM UNSET)

NG

GO TO STEERING LOCK SYSTEM (PROBLEM SYMPTOMS TABLE)

30.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER SYSTEM UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.*1


c.

Press the engine switch with the brake pedal*1 or clutch pedal*2 released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

*1: for CVT

*2: for Manual Transaxle


HINT:

It is determined that the immobiliser function is operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).


OK:

Security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

31.INSPECT PARK/NEUTRAL POSITION SWITCH

A

32.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)

B

REPLACE PARK/NEUTRAL POSITION SWITCH

C

REPLACE PARK/NEUTRAL POSITION SWITCH

D

32.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the C36 park/neutral position switch connector.


c.

Disconnect the A38 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M66-9 (STAR) - C36-4 (B) Always Below 1 Ω
M66-9 (STAR) or C36-4 (B) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

34.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SUPPLY AND BODY GROUND)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

34.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SUPPLY AND BODY GROUND)
a.
B331566C84
0.323,0.958 0.823,1.208 0.5,0.25 1.156,1.823 1.385,1.354 true 2.573,1.813 2.448,1.344 true 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 1.01,1.844 1.406,2.063 0.396,0.219 10 false GND 0.448,1 0.844,1.219 0.396,0.219 10 false A45 2.563,1.833 2.958,2.052 0.396,0.219 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A45-7 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

35.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

35.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the M67 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A38 ECM connector.


c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the F19 shift lock control unit assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M67-25 (STP1) - A45-3 (L) Always Below 1 Ω
M67-25 (STP1) or A45-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

36.INSPECT CLUTCH SWITCH ASSEMBLY
a.

Remove the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


b.

Inspect the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

37.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH SWITCH ASSEMBLY)

NG

REPLACE CLUTCH SWITCH ASSEMBLY

37.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH SWITCH ASSEMBLY)
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A51 clutch switch assembly connector.


c.

Disconnect the A38 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M66-9 (STAR) - A51-2 Always Below 1 Ω
M66-9 (STAR) or A51-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR