If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.
With the electrical key transmitter sub-assembly in the cabin, the engine switch is pressed.
When the transmitter battery of the electrical key transmitter sub-assembly is depleted, the brake pedal is depressed with the electrical key transmitter sub-assembly held near the engine switch.
When the entry and start system has been canceled, the brake pedal is depressed with the electrical key transmitter sub-assembly held near the engine switch.
| Problem Symptom | Data List and Active Test |
|---|---|
| Power source mode does not change to on (IG) or on (ACC) | Power Source Control
·
Start Switch1 ·
Start Switch2 ·
IG Relay Monitor (Inside) ·
ACC Relay Monitor ·
IG Relay Monitor (Outside) ·
Latch Circuit ·
Power Supply Condition Starting Control
·
Ignition |
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.
If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.
Inspect the fuses of circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to entry and start system (for Start Function) Precaution.
After completing repairs, confirm that the problem does not recur.
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
Press a switch of the electrical key transmitter sub-assembly.
The electrical key transmitter sub-assembly LED illuminates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Key Low Battery | Transmitter battery depleted | No or Yes | No: Transmitter battery not depleted
Yes: Transmitter battery depleted |
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new). |
| Tester Display |
|---|
| Key Low Battery |
"No" is displayed on the GTS screen.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the entry lock and unlock functions operate on each door.
If the door control receiver is defective, code verification does not begin in the cabin and the entry lock and unlock functions do not operate.
| Result | Proceed to |
|---|---|
| Entry functions operate normally for all doors | A |
| An entry function does not operate normally for a door | B |
A
B
Remove the transmitter battery from the electrical key transmitter sub-assembly.
| *1 | Engine Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
With the brake pedal*1 or clutch pedal*2 depressed, hold the electrical key transmitter sub-assembly near the engine switch and check if the power source mode changes.
*1: for CVT
*2: for Manual Transaxle
If the power source mode changes, the cabin verification is malfunctioning.
The power source mode changes.
| Result | Proceed to |
|---|---|
| The power source mode changes | A |
| The power source mode does not change | B |
A
B
Install the transmitter battery to the electrical key transmitter sub-assembly.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>INSTALLATION
Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform an entry and start system check.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).
Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (rear floor) and perform an entry and start system check.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 2 indoor electrical key antenna assembly (rear floor).
Check that the customize setting "Ignition Available Area" is set to "All".
Bring the electrical key transmitter sub-assembly near the No. 3 indoor electrical key antenna assembly (inside luggage compartment) and perform an entry and start system check.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 3 indoor electrical key antenna assembly (inside luggage compartment).
Check that the customize setting "Ignition Available Area" is set to "All".
As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
The engine starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the engine switch is pressed with the brake pedal depressed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for DTCs.
DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for DTCs.
DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the following antennas in key diagnostic mode.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
It is possible to check which indoor electrical key antenna assembly (front floor, rear floor or inside luggage compartment) is operating by the sounding of the buzzer.
When the wireless buzzer sounds for all indoor electrical key antenna assemblies, they can be judged as operating properly and a malfunction in the certification ECU (smart key ECU assembly), which performs verification, is suspected.
When the wireless buzzer does not sound for all indoor electrical key antenna assemblies, it can be judged that the certification ECU (smart key ECU assembly), which controls the indoor electrical key antenna assemblies, is malfunctioning.
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna assembly (front floor).
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.
| *a | Inspection Point |
Check the No. 2 indoor electrical key antenna assembly (rear floor).
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.
| *a | Inspection Point |
Check the No. 3 indoor electrical key antenna assembly (inside luggage compartment).
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.
| Result | Proceed to |
|---|---|
| The wireless buzzer does not sound for all indoor electrical key antenna assemblies | A |
| The wireless buzzer does not sound for only the No. 1 indoor electrical key antenna assembly (front floor) | B |
| The wireless buzzer does not sound for only the No. 2 indoor electrical key antenna assembly (rear floor) | C |
| The wireless buzzer does not sound for only the No. 3 indoor electrical key antenna assembly (inside luggage compartment) | D |
| The wireless buzzer sounds for all indoor electrical key antenna assemblies | E |
A
B
C
D
E
Using an oscilloscope, check the waveform.
| *a | Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna Assembly (Front Floor)) |
*b | Waveform 1 |
| *c | For 30 seconds after closing any door | *d | After 30 seconds or more have elapsed since any door closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F58-1 (ANTE5) - F58-3 (CLGB) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the No. 1 indoor electrical key antenna assembly (front floor) with a new one.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR (for Front Floor)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P.*1
Press the engine switch with the brake pedal*1 or clutch pedal*2 released and check that the power source mode changes.
*1: for CVT
*2: for Manual Transaxle
| Result | Proceed to |
|---|---|
| The power source mode changes | A |
| The power source mode does not change | B |
A
B
Using an oscilloscope, check the waveform.
| *a | Front view of wire harness connector
(to No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor)) |
*b | Waveform 1 |
| *c | For 30 seconds after closing any door | *d | After 30 seconds or more have elapsed since any door closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M10-1 (ANTE6) - M10-3 (CLGB) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the No. 2 indoor electrical key antenna assembly (rear floor) with a new one.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR (for Rear Floor)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P.*1
Press the engine switch with the brake pedal*1 or clutch pedal*2 released and check that the power source mode changes.
*1: for CVT
*2: for Manual Transaxle
| Result | Proceed to |
|---|---|
| The power source mode changes | A |
| The power source mode does not change | B |
A
B
Using an oscilloscope, check the waveform.
| *a | Front view of wire harness connector
(to No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment)) |
*b | Waveform 1 |
| *c | For 30 seconds after closing any door | *d | After 30 seconds or more have elapsed since any door closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M37-1 (ANTE7) - M37-3 (CLGB) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the No. 3 indoor electrical key antenna assembly (inside luggage compartment) with a new one.
| Proceed to |
|---|
| NEXT |
NEXT
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P.*1
Press the engine switch with the brake pedal*1 or clutch pedal*2 released and check that the power source mode changes.
*1: for CVT
*2: for Manual Transaxle
| Result | Proceed to |
|---|---|
| The power source mode changes | A |
| The power source mode does not change | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Start Switch1 | Engine switch 1 status | OFF or ON | OFF: Engine switch not pressed
ON: Engine switch pressed |
·
If the engine switch is pressed for a short time, the display may not change. ·
Use this item to determine if the engine switch input signal is malfunctioning. |
| Start Switch2 | Engine switch 2 status | OFF or ON | OFF: Engine switch not pressed
ON: Engine switch pressed |
·
Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal. ·
Behaves the same way as engine switch 1. |
| Tester Display |
|---|
| Start Switch1 |
| Start Switch2 |
The GTS display changes correctly in response to the engine switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the engine switch.
for 8NR-FTS with LHD: Click hereEngine / Hybrid System>8NR-FTS (STARTING)>ENGINE SWITCH (for LHD)>REMOVAL
for 8NR-FTS with RHD: Click hereEngine / Hybrid System>8NR-FTS (STARTING)>ENGINE SWITCH (for RHD)>REMOVAL
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE (STARTING)>ENGINE SWITCH>REMOVAL
Inspect the engine switch.
for 8NR-FTS with LHD: Click hereEngine / Hybrid System>8NR-FTS (STARTING)>ENGINE SWITCH (for LHD)>INSPECTION
for 8NR-FTS with RHD: Click hereEngine / Hybrid System>8NR-FTS (STARTING)>ENGINE SWITCH (for RHD)>INSPECTION
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE (STARTING)>ENGINE SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 8NR-FTS with LHD) | B |
| NG (for 8NR-FTS with RHD) | C |
| NG (for 3ZR-FAE) | D |
A
B
C
D
Disconnect the F1 certification ECU (smart key ECU assembly) connector.
Disconnect the F59 engine switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-23 (SSW1) - F59-5 (SS1) | Always | Below 1 Ω |
| F1-21 (SSW2) - F59-1 (SS2) | Always | Below 1 Ω |
| F1-11 (AGND) - F59-6 (AGND) | Always | Below 1 Ω |
| F1-23 (SSW1) or F59-5 (SS1) - Body ground | Always | 10 kΩ or higher |
| F1-21 (SSW2) or F59-1 (SS2) - Body ground | Always | 10 kΩ or higher |
| F1-11 (AGND) or F59-6 (AGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the following antennas in key diagnostic mode.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
It is possible to check if the transponder key amplifier built into the engine switch is operating by the sounding of the buzzer.
| *1 | Engine Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
Check the engine switch.
Face the logo side of the electrical key transmitter sub-assembly toward the engine switch, hold the electrical key transmitter sub-assembly near the engine switch and check that the wireless buzzer sounds.
| Result | Proceed to |
|---|---|
| The wireless buzzer does not sound | A |
| The wireless buzzer sounds (for 8NR-FTS with LHD) | B |
| The wireless buzzer sounds (for 8NR-FTS with RHD) | C |
| The wireless buzzer sounds (for 3ZR-FAE) | D |
A
B
C
D
Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| Entry and start system (for Start Function) DTCs are output | B |
A
B
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>B2271
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>B2271
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F1 certification ECU (smart key ECU assembly) connector.
Disconnect the 3A and 3D instrument panel junction block assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-16 (ACCD) - 3A-30 | Always | Below 1 Ω |
| F1-17 (IG1D) - 3A-17 | Always | Below 1 Ω |
| 3D-3 - Body ground | Always | Below 1 Ω |
| F1-16 (ACCD) or 3A-30 - Body ground | Always | 10 kΩ or higher |
| F1-17 (IG1D) or 3A-17 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-30 - 3D-3 | 20°C (68°F) | 285.71 to 428.57 Ω |
| 3A-17 - 3D-3 | 20°C (68°F) | 85.69 to 124.1 Ω |
| 3K-1 - 3A-40 | Battery voltage applied between terminals 3A-30 and 3D-3 | Below 1 Ω |
| Battery voltage not applied between terminals 3A-30 and 3D-3 | 10 kΩ or higher | |
| 3K-1 - 3F-10 | Battery voltage applied between terminals 3A-17 and 3D-3 | Below 1 Ω |
| Battery voltage not applied between terminals 3A-17 and 3D-3 | 10 kΩ or higher | |
| 3K-1 - 3H-12 | Battery voltage applied between terminals 3A-17 and 3D-3 | Below 1 Ω |
| Battery voltage not applied between terminals 3A-17 and 3D-3 | 10 kΩ or higher | |
| 3L-1 - 3D-19 | Battery voltage applied between terminals 3A-17 and 3D-3 | Below 1 Ω |
| Battery voltage not applied between terminals 3A-17 and 3D-3 | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Install the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>INSTALLATION
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>INSTALLATION
Reconnect the F1 certification ECU (smart key ECU assembly) connector.
Measure the voltage while confirming the power source mode on the Data List.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | Power supply state | All OFF, ACC ON, IG ON or ST ON | All OFF: Engine switch off
ACC ON: Engine switch on (ACC) IG ON: Engine switch on (IG) ST ON: Sending engine start request signal |
- |
| Tester Display |
|---|
| Power Supply Condition |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F1-17 (IG1D) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | 1 V or less | |
| Engine switch on (IG) | 9 V or higher | |
| F1-16 (ACCD) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | 8.5 V or higher | |
| Engine switch on (IG) | 8.5 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Inspect the transmitter battery.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>INSPECTION
Do not wrap the lead wire ground a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG