Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2015.04–2016.05
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM S

NETWORKING  CAN COMMUNICATION SYSTEM  DIAGNOSTIC TROUBLE CODE CHART  


DIAGNOSTIC TROUBLE CODE CHART
DTC No. Detection Item DTC Detection Condition Trouble Area Note Link
U0104 Lost Communication with Driving Support ECU No communication from the driving support ECU assembly continues.
·

Driving support ECU assembly branch line or connector

·

Power source circuit of driving support ECU assembly

·

Driving support ECU assembly ground circuit

·

Driving support ECU assembly


The network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2. Click here
U0199 Lost Communication with "Door Control Module A" No communication from the outer mirror control ECU assembly continues.
·

Outer mirror control ECU assembly (for driver side) branch line or connector

·

Power source circuit of outer mirror control ECU assembly (for driver side)

·

Outer mirror control ECU assembly (for driver side) ground circuit

·

Outer mirror control ECU assembly (for driver side)


The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1. Click here
U0200 Lost Communication with "Door Control Module B" No communication from the outer mirror control ECU assembly continues.
·

Outer mirror control ECU assembly (for front passenger side) branch line or connector

·

Power source circuit of outer mirror control ECU assembly (for front passenger side)

·

Outer mirror control ECU assembly (for front passenger side) ground circuit

·

Outer mirror control ECU assembly (for front passenger side)


The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1. Click here
U0208 Lost Communication with "Seat Control Module A" No communication from the position control ECU and switch assembly continues.
·

Position control ECU and switch assembly (for driver side) branch line or connector

·

Power source circuit of position control ECU and switch assembly (for driver side)

·

Position control ECU and switch assembly (for driver side) ground circuit

·

Position control ECU and switch assembly (for driver side)


The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1. Click here
U0233 Lost Communication with Blind Spot Monitor Master Module No communication from the blind spot monitor sensor RH continues.
·

Blind spot monitor sensor RH branch line or connector

·

Power source circuit of blind spot monitor sensor RH

·

Blind spot monitor sensor RH ground circuit

·

Blind spot monitor sensor RH


The network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2. Click here
U0235 Lost Communication with Cruise Control Front Distance Range Sensor No communication from the millimeter wave radar sensor assembly continues.
·

Open or short in sub bus 13 main line or connector

·

Millimeter wave radar sensor assembly

·

Power source circuit of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit


The driving support ECU assembly stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 13. Click here
U023A Lost Communication with Front Camera Module No communication from the lane departure warning camera continues.
·

Lane departure warning camera branch line or connector

·

Power source circuit of lane departure warning camera

·

Lane departure warning camera ground circuit

·

Lane departure warning camera


The network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2. Click here
U0265 Lost Communication with Parking Assist Monitor Module No communication from the rear television camera assembly continues.
·

Rear television camera assembly branch line or connector

·

Power source circuit of rear television camera assembly

·

Rear television camera assembly ground circuit

·

Rear television camera assembly


Network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2. Click here
U1002 Lost Communication with Gateway Module (Main Body ECU) Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to sub bus 1.
·

Open or short in Sub bus 1 main line or connector

·

Open or short in Sub bus 1 branch line or connector

·

Main body ECU (Multiplex network body ECU)

·

Outer mirror control ECU assembly (for Driver side)

·

Outer mirror control ECU assembly (for Front passenger side)

·

Position control ECU and switch assembly (for Driver side)

·

Open or short in CAN No. 3 junction connector

·

Open or short in CAN No. 4 junction connector


The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1. Click here
U1002 Lost Communication with Gateway Module (Sensor Bus) The driving support ECU assembly does not receive signals from all ECUs that have been memorized as those connected to sub bus 13.
·

Open or short in sub bus 13 main line or connector

·

Driving support ECU assembly

·

Power source circuit of driving support ECU assembly

·

Driving support ECU assembly ground circuit

·

Millimeter wave radar sensor assembly

·

Power source circuit of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit


The driving support ECU assembly stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 13. Click here
U1002 Lost Communication with Gateway Module (Network Gateway ECU) The network gateway ECU does not receive signals from all ECUs that have been memorized as those connected to sub bus 2.
·

Open or short in sub bus 2 main lines or connector

·

Short in sub bus 2 branch lines or connector

·

Network gateway ECU

(w/ Parking Assist Monitor System or Pre-crash Safety System)

·

Blind spot monitor sensor RH

(w/ Pre-crash Safety System)

·

Rear television camera assembly

(w/ Parking Assist Monitor System or Pre-crash Safety System)

·

Driving support ECU assembly

(w/ Pre-crash Safety System)

·

Lane departure warning camera

(w/ Pre-crash Safety System)

·

Open or short in CAN No. 5 junction connector

(w/ Parking Assist Monitor System or Pre-crash Safety System)

·

Open or short in CAN No. 6 junction connector

(w/ Parking Assist Monitor System or Pre-crash Safety System)

·

Open or short in CAN No. 7 junction connector

(w/ Parking Assist Monitor System or Pre-crash Safety System)

·

Open or short in CAN No. 8 junction connector

(w/ Pre-crash Safety System)

·

Open or short in CAN No. 9 junction connector

(w/ Parking Assist Monitor System or Pre-crash Safety System)


The network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2. Click here