Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge) › 2011.10–2013.07
RM19V0EQ _53 Suspension _014588 FRONT SUSPENSION _0281054 FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge) A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.

for Automatic Transaxle:

i.

Install 5 hole plugs to the front frame assembly.



b.

for Manual Transaxle:

i.

Install 4 hole plugs to the front frame assembly.



Hide 52217E 2.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH

a.
C238985C03
0.175,0.109 0.345,0.258 0.17,0.149 10 *a
*a View from Underneath
V100135

Front of the Vehicle


Temporarily install a new front suspension member body mounting rear cushion LH while confirming the installation direction.

NOTICE:

Position the front suspension member body mounting rear cushion LH in the correct direction.



b.
C169232C04
1.198,1.5 1.417,1.5 1.417,1.5 1.531,2.125 false 2.49,0.854 2.01,0.854 false 2.198,2.698 2.521,2.698 false 1.01,1.427 1.188,1.594 0.177,0.167 10 *1 2.542,0.771 2.865,0.938 0.323,0.167 10 SST 2.542,2.615 2.865,2.781 0.323,0.167 10 SST
*1 Front Suspension Member Body Mounting Rear Cushion LH


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)


c.
C167152C02
1.646,1.5 2.052,1.5 false 0.563,2.229 0.979,2.323 false 2.396,0.854 2.302,0.854 2.302,0.854 2.24,0.792 false 0.969,3.156 0.833,3.156 0.833,3.156 0.771,3.083 false 2.406,0.76 2.625,0.938 0.219,0.177 10 *a 2.083,1.406 2.438,1.573 0.354,0.167 10 SST 1,3.052 1.333,3.219 0.333,0.167 10 *b 0.198,2.146 0.552,2.313 0.354,0.167 10 SST
*a Hold
*b Turn


Using SST, install the front suspension member body mounting rear cushion LH as shown in the illustration.

NOTICE:

Check that there is no clearance between the front suspension member and the front suspension member body mounting rear cushion LH.



Hide 52215 3.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH

a.
C238987C03
0.166,0.121 0.339,0.271 0.173,0.15 10 *a
*a View from Underneath
V100135

Front of the Vehicle


Temporarily install a new front suspension member body mounting rear cushion RH while confirming the installation direction.

NOTICE:

Position the front suspension member body mounting rear cushion RH in the correct direction.



b.

Install SST using the same procedure as for the front suspension member body mounting rear cushion LH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)


c.

Using SST, install the front suspension member body mounting rear cushion RH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

HINT:

Perform the same procedure as for the LH side.



Hide 52211J 4.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION

a.
C238988C04
0.157,0.121 0.31,0.274 0.152,0.152 10 *a
*a View from Underneath
V100135

Front of the Vehicle


Temporarily install a new front suspension member body mounting front cushion while confirming the installation direction.

NOTICE:

Position the front suspension member body mounting front cushion in the correct direction.



b.

Install SST using the same procedure as for the front suspension member body mounting rear cushion LH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)


c.
C167148C02
2.271,0.74 2.479,0.74 false 1.646,1.354 2.125,1.198 false 0.771,2.292 0.969,2.406 false 1.042,3.021 1.25,3.073 false 2.5,0.646 2.688,0.802 0.188,0.156 10 *a 1.26,3 1.604,3.177 0.344,0.177 10 *b 0.49,2.208 0.802,2.375 0.313,0.167 10 SST 2.167,1.104 2.479,1.271 0.313,0.167 10 SST
*a Hold
*b Turn


Using SST, install the front suspension member body mounting front cushion as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Check that there is no clearance between the front suspension member and the front suspension member body mounting front cushion.



Hide 52216B 5.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER

a.

Install the 2 front suspension member body mounting rear stoppers to the front frame assembly.


Hide 52213A 6.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER

a.

Install the 2 front suspension member body mounting front stoppers to the front frame assembly.


Hide 51227B 7.INSTALL FRONT SUSPENSION MEMBER DYNAMIC DAMPER

a.

Install the front suspension member dynamic damper to the front frame assembly with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 48069 8.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly LH.


b.
C167143E01
0.656,0.357 0.795,0.515 0.139,0.158 10 1 1.147,0.24 1.286,0.398 0.139,0.158 10 2 2.467,0.926 2.613,1.077 0.146,0.150 10 3

Install the front lower No. 1 suspension arm sub-assembly LH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.

Torque:
Bolt 1, 2 : 200 N*m (2039 kgf*cm, 148 ft.*lbf)
Bolt 3 : 135 N*m (1377 kgf*cm, 100 ft.*lbf)

NOTICE:

While keeping the nut from rotating, tighten the bolt.



Hide 48068 9.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 10.INSTALL STEERING LINK ASSEMBLY

Hide 11.INSTALL FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY

a.

Install the front stabilizer bar with 2 front stabilizer link assemblies to the front frame assembly.


Hide 48829A 12.INSTALL FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 13.INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 51100G 14.INSTALL FRONT FRAME ASSEMBLY

a.

Slowly jack up the front frame assembly with an engine lifter using 4 attachments or equivalent tools.

CAUTION:
·

The front frame assembly is a heavy component. Make sure that it is supported securely.

·

Make sure to secure the front frame assembly to prevent it from dropping.



NOTICE:

Use the attachments to keep the front frame assembly level.



b.
A331865N01
0.74,1.354 0.854,1.531 0.115,0.177 10 true A 2.604,1.354 2.719,1.531 0.115,0.177 10 true A 0.188,0.313 0.302,0.49 0.115,0.177 10 true B 0.719,0.042 0.833,0.219 0.115,0.177 10 true B 2.594,0.021 2.708,0.198 0.115,0.177 10 true B 3.125,0.323 3.24,0.5 0.115,0.177 10 true B 1.104,3.021 1.219,3.198 0.115,0.177 10 true C 2.208,3.01 2.323,3.188 0.115,0.177 10 true C 3.135,2.427 3.25,2.604 0.115,0.177 10 true D 2.74,3.177 2.854,3.354 0.115,0.177 10 true D 0.615,3.177 0.729,3.354 0.115,0.177 10 true D 0.188,2.438 0.302,2.615 0.115,0.177 10 true D

Install the frame side rail plates RH and LH with the 4 bolts and 2 nuts.

Torque:
A : 85 N*m (867 kgf*cm, 63 ft.*lbf)
B : 32 N*m (326 kgf*cm, 24 ft.*lbf)


c.

Install the front suspension member rear braces RH and LH with the 4 bolts and 2 nuts.

Torque:
C : 85 N*m (867 kgf*cm, 63 ft.*lbf)
D : 32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 15.REMOVE BELT

a.

Remove SST from the vehicle body.

C313255N01
0.99,2.052 3.229,2.052 true 3.719,2.063 6.094,2.063 true 0.698,1.979 1.156,2.177 0.458,0.198 10 false SST 6.135,1.99 6.594,2.188 0.458,0.198 10 false SST


b.

Connect the windshield washer jar assembly to the vehicle body and tighten the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Install the bolt and nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 16.REMOVE ENGINE SUPPORT BRIDGE

a.

Remove SST from the vehicle body.

NOTICE:

Prevent SST from contacting the vehicle body or windshield.



b.

Install the 2 hood support assemblies.

Click hereVehicle Exterior>DOOR / HATCH>HOOD SUPPORT>INSTALLATION


Hide 17.REMOVE ENGINE HANGERS

a.

Remove the 2 bolts and No. 1 and No. 2 engine hangers from the engine assembly.


Hide 12327A 18.INSTALL NO. 2 ENGINE MOUNTING STAY RH

Hide 12361A 19.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Install the front engine mounting insulator to the front frame assembly with the 3 nuts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 12372A 20.INSTALL ENGINE MOUNTING INSULATOR LH

a.

Install the engine mounting insulator LH to the front frame assembly with the 3 nuts.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)


b.

Install the 2 hole plugs.


Hide 12362 21.INSTALL ENGINE MOUNTING INSULATOR RH

a.

Install the engine mounting insulator RH to the front frame assembly with the 3 nuts.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)


b.

Install the 2 hole plugs.


Hide 12364A 22.INSTALL ENGINE LATERAL CONTROL ROD (for Manual Transaxle)

a.

Install the engine lateral control rod to the front frame assembly with the 2 nuts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


b.

Install the 2 hole plugs.


Hide 45220 23.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 43420 24.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 25.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 26.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 27.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45470 28.CONNECT TIE ROD ASSEMBLY LH

Hide 45460 29.CONNECT TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 30.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 31.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 43502H 32.INSTALL FRONT AXLE SHAFT NUT LH

Hide 43501H 33.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Perform the same procedure as for the LH side.


Hide 17410 34.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 17771A 35.INSTALL NO. 1 AIR CLEANER BRACKET

Hide 17701 38.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 39.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17735 40.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17750A 41.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 42.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 43.INSPECT FOR EXHAUST GAS LEAK

Hide 12601B 44.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 53737B 45.INSTALL FRONT FENDER APRON SEAL LH

Hide 53736 46.INSTALL FRONT FENDER APRON SEAL RH

Hide 51442C 47.INSTALL ENGINE UNDER COVER LH

Hide 53852K 48.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (for RHD)

Hide 51441C 49.INSTALL ENGINE UNDER COVER RH

Hide 53851Z 50.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)

Hide 51.INSTALL FRONT WHEELS

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 52.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT