Home › Engine / Hybrid System · 1AZ-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > Starter Signal Circuit

for Preparation Click here


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition or starter switch assembly to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).

WIRING DIAGRAM

Refer to DTC P0617 .

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK WHETHER ENGINE CAN BE CRANKED
  1. Check if the engine can be cranked.

    Result 
    Result
    Proceed to
    Engine cannot be cranked
    A
    Engine can be cranked
    B



B
Go to step 11
A


2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.

    OK 
    Ignition Switch Position
    Starter Signal
    ON
    Close (OFF)
    START
    Open (ON)



NG
Go to step 12
OK


3.INSPECT RELAY (ST RELAY)
  1. Inspect the ST relay (Click here).



NG
REPLACE RELAY (ST RELAY)
OK


4.INSPECT STARTER ASSEMBLY
  1. Inspect the starter assembly (Click here).



NG
REPLACE STARTER ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)
  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Disconnect the starter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 3 - E9-1
    Always
    Below 1 Ω
    ST relay terminal 3 or E9-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)
  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the cable from the positive (+) battery terminal.

  1. Disconnect the starter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    Positive (+) battery terminal - F2-1
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 1 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
  1. Disconnect the park/neutral position switch assembly connector.

  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E4-5 (L) - ST relay terminal 2
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
  1. Inspect the ignition or starter switch assembly (Click here).



NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST RELAY)
  1. Disconnect the ignition or starter switch assembly connector.

  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    I36-7 (ST2) - ST relay terminal 5
    Always
    Below 1 Ω
    I36-7 (ST2) or ST relay terminal 5 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY) 

11.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.

    OK 
    Ignition Switch Position
    Starter Signal
    ON
    Close (OFF)
    START
    Open (ON)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - ECM)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

12.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly (Click here).



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


13.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
  1. Inspect the ignition or starter switch assembly (Click here).



NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY (Click here)
OK


14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY AND ECM)
  1. Disconnect the ignition or starter switch assembly connector.

  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    I36-3 (ST1) - E4-4 (B)
    Always
    Below 1 Ω
    I36-3 (ST1) - E83-52 (NSW)
    Always
    Below 1 Ω
    I36-3 (ST1), E4-4 (B) or E83-52 (NSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY AND ECM)
  1. Disconnect the park/neutral position switch assembly connector.

  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E4-5 (L) - ST relay terminal 2
    Always
    Below 1 Ω
    E4-5 (L), ST relay terminal 2 or A74-48 (STA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)