Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT
RM2030EQ _58 Vehicle Interior _014672 HEATING / AIR CONDITIONING _0074654 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  INSTALLATION  


PROCEDURE

Hide 1.INSTALL AIR CONDITIONING UNIT ASSEMBLY

a.

Install the air conditioning unit assembly to the instrument panel reinforcement assembly with the 3 bolts.

E248493E01
2.031,1.229 2.302,1.229 false 3.25,1.167 3.063,1.292 false 1.854,1.146 2.219,1.448 0.365,0.302 10 false (1) 5.313,0.854 5.688,1.156 0.375,0.302 10 false (2) 2.896,1.25 3.208,1.531 0.313,0.281 10 false (3)

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration to install the air conditioning unit assembly.



Hide 2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT

NOTICE:
·

Be sure to support the air conditioning unit assembly when installing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When installing the air conditioning unit, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

Engage the 3 guides and temporarily install the instrument panel reinforcement assembly with air conditioning unit as shown in the illustration.

E248494


b.

Install the instrument panel reinforcement assembly with the 3 bolts <A> and 2 new bolts <B>.

E248495C01
3.26,1.5 3.021,1.583 false 3.563,1.385 3.74,1.177 false 3.667,1.729 3.771,1.635 false 0.01,3.063 0.5,3.385 0.49,0.323 10 false (1) 0.104,3.229 0.583,3.531 0.479,0.302 10 false (2) 0.042,3.594 0.438,3.906 0.396,0.313 10 false (3) 6.104,2.396 6.49,2.667 0.385,0.271 10 false (4) 6.146,2.708 6.583,2.979 0.438,0.271 10 false (5) 2.865,1.51 3.167,1.76 0.302,0.25 10 false *1 3.74,1.042 4.104,1.281 0.365,0.24 10 false *2 3.771,1.51 4.167,1.75 0.396,0.24 10 false *3 2.083,0.667 2.5,0.917 0.417,0.25 10 false *a 3.083,0.667 3.417,0.917 0.333,0.25 10 false *b 4.083,0.667 4.333,0.917 0.25,0.25 10 false *c 5.083,0.667 5.417,0.917 0.333,0.25 10 false *d 0.219,2.948 0.781,3.25 0.563,0.302 10 false <A> 0.302,3.333 0.771,3.615 0.469,0.281 10 false <A> 0.302,3.677 0.833,3.979 0.531,0.302 10 false <A> 5.906,2.563 6.438,2.813 0.531,0.25 10 false <B> 5.969,2.885 6.438,3.156 0.469,0.271 10 false <B> 2.656,4.073 3.094,4.354 0.438,0.281 10 false <C>
*1 Movable Collar *2 Body
*3 Instrument Panel Reinforcement - -
*a Step 1 *b Step 2
*c Step 3 *d Step 4


Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration to install the reinforcement assembly.



c.

Install the bolt <C>.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


d.

Install the instrument panel reinforcement assembly with air conditioning unit with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


e.

Pass the cooler drain hose through the vehicle securely.

NOTICE:

Connect the cooler drain hose firmly to prevent water leaks.



f.
E227180E06
1.031,0.833 1.208,0.635 false 2.448,0.958 2.271,0.688 false 2.073,0.542 2.552,0.833 0.479,0.292 10 false (1) 1.229,0.49 1.604,0.719 0.375,0.229 10 false (2)

Install the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration.



g.

Engage each clamp.


h.

Connect each connector.


i.

Connect the connector holder with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


j.

Connect the 3 earth wires with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


k.

Engage the claw to connect the airbag connector as shown in the illustration.

E227176


l.
E227174C07
2.073,2.667 2.458,2.938 false 2.479,2.875 2.875,3.167 0.396,0.292 10 false *1
*1 Retainer


Engage the 2 claws to lock the retainer as shown in the illustration.


m.
E236048C04
0.896,3.844 0.219,3.469 0.219,3.469 0.594,4.021 false 2,0.365 2.292,0.656 0.292,0.292 10 false *1 0.01,3.333 0.302,3.625 0.292,0.292 12 false *A
*A w/ Smart Entry and Start System
*1 Airbag Sensor Assembly


Engage each clamp.


n.

Connect each connector.


o.

Connect the connector to the airbag sensor assembly as shown in the illustration.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



p.
E227170

Engage the 3 claws to close the 3 clamps as shown in the illustration.


q.

for 10 Speakers:

i.

Engage the 3 clamps.



Hide 3.INSTALL FRONT LOWER PANEL PACKING

a.
E245761

Install the 2 front lower panel packings.


Hide 55458A 4.INSTALL INSTRUMENT PANEL SAFETY PAD CAP

a.

Install 5 new instrument panel safety pad caps.

E265294C04
0.667,0.219 1.156,0.5 0.49,0.281 12 false *A 3.844,0.219 4.281,0.521 0.438,0.302 12 false *B
*A for Driver Side *B for Passenger Side



Hide 55307E 5.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the screw.


b.

Install the 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Install the No. 2 instrument panel brace sub-assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


d.

Connect the earth wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Engage each clamp.


f.

Connect the connector.


Hide 55306B 6.INSTALL INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.

Install the screw.


b.

Install the 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Install the instrument panel to cowl brace sub-assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


d.

Connect the earth wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Engage each clamp.


f.

Connect each connector.


Hide 58861B 7.INSTALL NO. 1 CONSOLE BOX DUCT

a.

Install the No. 1 console box duct with the clip.


Hide 87212F 8.INSTALL REAR NO. 2 AIR DUCT

a.

Engage the 2 claws to install the rear No. 2 air duct.


Hide 58544A 9.INSTALL FLOOR CARPET BRACKET LH

a.

Engage the 2 guides.


b.

Install the floor carpet bracket LH with the 2 clips.


c.
E227459

Engage the guide to install the floor carpet to the original position as shown in the illustration.


Hide 77306 10.CONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

a.
E227151

Engage the guide to connect the fuel lid lock open lever sub-assembly as shown in the illustration.


b.

Install the screw.


Hide 87212 11.INSTALL REAR NO. 1 AIR DUCT

a.

Engage the 2 claws to install the rear No. 1 air duct.


Hide 58543B 12.INSTALL FLOOR CARPET BRACKET RH

a.

Engage the 2 guides.


b.

Install the floor carpet bracket RH with the 2 clips.


c.
E229495

Engage the guide to install the floor carpet to the original position as shown in the illustration.


Hide 58569D 13.INSTALL FRONT FLOOR CAUTION PLATE COVER

a.
E234874

Engage the guide and claw to install the front floor caution plate cover.


Hide 58521B 14.INSTALL FLOOR CARPET HOOK

a.

Engage the 6 claws to install the 6 floor carpet hooks.


b.

Engage the 6 guides.


Hide 85940 15.INSTALL WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)

Hide 88650N 16.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 82730 18.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD)

Hide 82730 19.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for RHD)

Hide 20.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 21.INSTALL STEERING POST ASSEMBLY

Hide 22.INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET (for 10 Speakers)

Hide 86183D 23.INSTALL AUDIO AMPLIFIER COVER (for 10 Speakers)

Hide 24.INSTALL FRONT SEAT ASSEMBLY LH (for RHD Manual Seat)

Hide 25.INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)

Hide 26.INSTALL FRONT SEAT ASSEMBLY RH (for LHD Manual Seat)

HINT:

Use the same procedure as for the LH side.


Hide 27.INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)

HINT:

Use the same procedure as for the LH side.


Hide 88710E 28.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the pipe.


b.

Sufficiently apply compressor oil to a new O-ring and fitting surface of the air conditioner tube and accessory assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the air conditioner tube and accessory assembly.


d.

Connect the air conditioner tube and accessory assembly.


Hide 88704 29.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction hose sub-assembly.


d.
E227143

Rotate the hook connector in the direction indicated by the arrow in the illustration.


e.

Insert the pipe joint into the cooler expansion valve securely and tighten the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87245 30.CONNECT HEATER INLET WATER HOSE

a.

Using pliers, grip the claws of the clip and slide the clip to connect the heater inlet water hose.


Hide 87246 31.CONNECT HEATER OUTLET WATER HOSE

a.

Using pliers, grip the claws of the clip and slide the clip to connect the heater outlet water hose.


Hide 55702A 32.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55702A 33.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 34.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 36.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR

Hide 38.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT