Refer to DTC P2195 (See page Engine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>P2195).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2A00 | A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) | The calculated value for the air fuel ratio sensor response rate deterioration level is less than the threshold (2 trip detection logic). | ·
Air fuel ratio sensor (sensor 1) ·
Intake system ·
Fuel injector assembly ·
Fuel pump ·
Fuel line ·
EGR valve assembly ·
ECM |
Comes on | DTC stored |
After the engine is warmed up, the ECM performs air fuel ratio feedback control to maintain the air fuel ratio at the stoichiometric level. In addition, active air fuel ratio control is performed for approximately 30 seconds after preconditions are met in order to measure the air fuel ratio sensor response rate. During active air fuel ratio control, the ECM forcibly increases and decreases the injection volume by a certain amount, based on the stoichiometric air fuel ratio learned during normal air fuel ratio control, and measures the air fuel ratio sensor response rate. The ECM receives a signal from the air fuel ratio sensor while performing active air fuel ratio control and uses it to calculate the air fuel ratio sensor response rate deterioration level.
If the value for the air fuel ratio sensor response rate deterioration level is less than the threshold, the ECM interprets this as a malfunction and stores the DTC.
| Required Sensors/Components | Air fuel ratio sensor |
| Frequency of Operation | Once per driving cycle |
| Active air fuel ratio control | Performing |
| Active air fuel ratio control performed when following conditions met | - |
| Engine coolant temperature | 75°C (167°F) or higher |
| Idling | Off |
| Engine speed | Less than 4000 rpm |
| Air fuel ratio sensor status | Activated |
| Engine load | 10% or higher, and less than 70% |
| Catalyst monitor | Not yet |
| Mass air flow | 3.1 gm/sec or more, and less than 12 gm/sec |
Performing this confirmation driving pattern will activate the air fuel ratio sensor response monitor.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the tester on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
Drive the vehicle at approximately 60 to 100 km/h (37 to 62 mph) for 10 minutes or more in a city area [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine and ECT / DTC [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2A00.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A and no pending DTC is output, perform the following procedure.
Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes [D].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine and ECT / DTC [E].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2A00.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, drive the vehicle again under an increased load and then recheck the judgment result.
Refer to DTC P0031 (See page Engine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>P0031).
Inspect the fuses for circuits related to this system before performing the following procedure.
DTC P2A00 may be also stored when the air fuel ratio is stuck at rich or lean.
A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2A00 is output | A |
| DTC P2A00 and other DTCs are output | B |
If any DTCs other than P2A00 are output, troubleshoot those DTCs first.
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
| Tester Display |
|---|
| Inspection Mode |
Start the engine.
Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, warm up the engine after charging control has completed.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.
| Active Test Display |
|---|
| Control the Injection Volume for A/F Sensor |
| Data List Display |
|---|
| AFS Voltage B1S1 |
| O2S B1S2 |
Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.
Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
|---|---|---|---|
| AFS Voltage B1S1
(Air fuel ratio) |
12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2
(Heated oxygen) |
12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status of AFS Voltage B1S1 | Status of O2S B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Proceed to |
|---|---|---|---|
| Lean/Rich | Lean/Rich | Normal | A |
| Lean | Lean | Actual air fuel ratio lean | B |
| Rich | Rich | Actual air fuel ratio rich | |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | C |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction |
Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.
Rich: During the Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.
Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the heated oxygen sensor alternates correctly.
Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2].
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
A
B
C
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P2A00.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2A00 is output) | B |
A
B
OK
NG
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>2AR-FXE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks in the intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel pressure.
Click hereEngine / Hybrid System>2AR-FXE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel injector assembly.
Click hereEngine / Hybrid System>2AR-FXE FUEL>FUEL INJECTOR>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air fuel ratio sensor.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P2A00.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL (DTC P2A00 is output) | A |
| NORMAL (DTC is not output) | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
The A/C switch and all accessory switches should be off and shift lever in Por N.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / All Data / MAP and Throttle Idle Position.
| Active Test Display |
|---|
| Control the EGR Step Position |
| Data List Display |
|---|
| MAP |
| Throttle Idle Position |
Confirm that the Throttle Idle Position is ON and check the MAP values in the Data List while performing the Active Test.
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.
| - | EGR Step Position (Active Test) | |
|---|---|---|
| 0 Steps | 0 to 30 Steps | |
| MAP
(Data List) |
(EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly maybe a malfunctioning.
Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.
| Result | Proceed to |
|---|---|
| Outside of standard range | A |
| Within standard range | B |
A
B
Remove the EGR valve assembly.
Click hereEngine / Hybrid System>2AR-FXE EMISSION CONTROL>EGR VALVE>REMOVAL
Check if the EGR valve is stuck open.
EGR valve is tightly closed.
Perform "Inspection After Repair" after replacing the EGR valve assembly.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P2A00.
Check that the DTC judgment result is NORMAL.
| Proceed to |
|---|
| NEXT |
NEXT
Check the fuel lines for leaks or blockage.
Perform "Inspection After Repair" after replacing the fuel pump.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG