Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1235/35  Foreign Object is Attached on Tip of Front Speed Sensor RH  C1236/36  Foreign Object is Attached on Tip of Front Speed Sensor LH  C1238/38  Foreign Object is Attached on Tip of Rear Speed Sensor RH  C1239/39  Foreign Object is Attached on Tip of Rear Speed Sensor LH  C1275/75  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1276/76  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1277/77  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1278/78  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)  


DESCRIPTION

When foreign matter adheres to the speed sensor tip or speed sensor rotor, these DTCs are stored. The presence of foreign matter can be judged when an abnormal waveform is received from a sensor.

These DTCs may also be detected when a malfunction occurs in the connector terminals or wire harness of the speed sensor circuit.

DTCs C1275/75 to C1278/78 will be cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs from C1275/75 to C1278/78 are output only in Test Mode.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1235/35 Foreign Object is Attached on Tip of Front Speed Sensor RH 541 Either of the following is detected:
1.

When driving at 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

2.

When driving at 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.


·

Speed sensor rotor malfunction (foreign object attached)

·

Foreign object attached to speed sensor

·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Resistance in speed sensor circuit

·

Skid control ECU (Brake booster with master cylinder assembly)


ABS DTC
C1236/36 Foreign Object is Attached on Tip of Front Speed Sensor LH 542 Either of the following is detected:
1.

When driving at 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

2.

When driving at 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.


·

Speed sensor rotor malfunction (foreign object attached)

·

Foreign object attached to speed sensor

·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Resistance in speed sensor circuit

·

Skid control ECU (Brake booster with master cylinder assembly)


ABS DTC
C1238/38 Foreign Object is Attached on Tip of Rear Speed Sensor RH 543 Either of the following is detected:
1.

When driving at 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

2.

When driving at 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.


·

Speed sensor rotor malfunction (foreign object attached)

·

Foreign object attached to speed sensor

·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Resistance in speed sensor circuit

·

Skid control ECU (Brake booster with master cylinder assembly)


ABS DTC
C1239/39 Foreign Object is Attached on Tip of Rear Speed Sensor LH 544 Either of the following is detected:
1.

When driving at 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

2.

When driving at 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.


·

Speed sensor rotor malfunction (foreign object attached)

·

Foreign object attached to speed sensor

·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Resistance in speed sensor circuit

·

Skid control ECU (Brake booster with master cylinder assembly)


ABS DTC
C1275/75 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) - Detected only during Test Mode.
·

Front speed sensor RH

·

Front speed sensor rotor RH (Front drive outboard joint shaft assembly RH)


ABS Test Mode DTC
C1276/76 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) - Detected only during Test Mode.
·

Front speed sensor LH

·

Front speed sensor rotor LH (Front drive outboard joint shaft assembly LH)


ABS Test Mode DTC
C1277/77 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) - Detected only during Test Mode.
·

Rear speed sensor RH

·

Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH)


ABS Test Mode DTC
C1278/78 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) - Detected only during Test Mode.
·

Rear speed sensor LH

·

Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH)


ABS Test Mode DTC

HINT:
·

DTCs C1235/35 and C1275/75 are for the front speed sensor RH.

·

DTCs C1236/36 and C1276/76 are for the front speed sensor LH.

·

DTCs C1238/38 and C1277/77 are for the rear speed sensor RH.

·

DTCs C1239/39 and C1278/78 are for the rear speed sensor LH.



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK DTC
a.

Check that no speed sensor malfunction DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

When C1464/31, C1465/32, C1466/33, and/or C1467/34 are output together with C1235/35, C1236/36, C1238/38, and/or C1239/39, inspect and repair the trouble areas indicated by C1464/31, C1465/32, C1466/33, and/or C1467/34 first.



Result:
Result Proceed to
DTCs C1235/35 and/or C1236/36 are output. A
DTCs C1238/38 and C1239/39 are output. B
Speed sensor malfunction DTCs (C1464/31, C1465/32, C1466/33 and/or C1467/34) are output. C



A

2.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR

B

10.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)

C

2.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR

b.

Check the speed sensor tip and speed sensor rotor.

OK:

The sensor tip and rotor is free of scratches, oil, and foreign matter.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR OR COMPONENT WITH SENSOR ROTOR

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.

Install the front speed sensor and the component with the sensor rotor.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector and the A53 or A16 front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A28-18 (FR+) - A53-1 (FR+) Always Below 1 Ω
A28-18 (FR+) - Body ground Always 10 kΩ or higher
A28-5 (FR-) - A53-2 (FR-) Always Below 1 Ω
A28-5 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A28-31 (FL+) - A16-1 (FL+) Always Below 1 Ω
A28-31 (FL+) - Body ground Always 10 kΩ or higher
A28-32 (FL-) - A16-2 (FL-) Always Below 1 Ω
A28-32 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)
a.
C248346C06
0.177,1.219 0.615,1.51 0.438,0.292 1.76,1.219 2.198,1.51 0.438,0.292 2.604,1.948 3.115,2.729 false 1.188,1.958 1.708,2.729 false 0.281,0.177 0.521,0.354 0.24,0.177 10 false *a 1.552,2.76 1.99,3.073 0.438,0.313 10 false FR+ 2.99,2.75 3.406,3.042 0.417,0.292 10 false FL+ 0.292,1.271 0.708,1.5 0.417,0.229 10 false A53 1.875,1.271 2.292,1.604 0.417,0.333 10 false A16
*a Front view of wire harness connector
(to Front Speed Sensor)


Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
A53-1 (FR+) - Body ground Power switch on (IG) 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
A16-1 (FL+) - Body ground Power switch on (IG) 5.7 to 14 V



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.RECONFIRM DTC
a.

Turn the power switch off.


b.

Reconnect the A53 or A16 front speed sensor connector.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the power switch on (READY).


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1235/35 and/or C1236/36 are output. A
DTCs C1235/35 and C1236/36 are not output. B



A

6.REPLACE FRONT SPEED SENSOR

B

6.REPLACE FRONT SPEED SENSOR
a.

Turn the power switch off.



Result:
Proceed to
NEXT



NEXT

7.RECONFIRM DTC
7.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch on (READY).


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1235/35 and/or C1236/36 are output. A
DTCs C1235/35 and C1236/36 are not output. B



A

8.REPLACE FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY

B

END

8.REPLACE FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY
a.

Turn the power switch off.


b.

Replace the front speed sensor rotor (front drive outboard joint shaft assembly).

Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY>DISASSEMBLY

HINT:

If the front speed sensor rotor needs to be replaced, replace the front drive outboard joint shaft assembly.


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
NEXT



NEXT

9.RECONFIRM DTC
9.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch on (READY).


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1235/35 and/or C1236/36 are output. A
DTCs C1235/35 and C1236/36 are not output. B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

END

10.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)
a.
C276199C03
0.208,2.542 0.563,2.792 0.354,0.25 0.198,0.615 0.552,0.865 0.354,0.25 1.844,0.635 2.198,0.885 0.354,0.25 1.927,2.677 2.281,2.927 0.354,0.25 0.604,1.958 0.948,1.26 false 1.417,1.938 1.198,1.26 false 2.698,1.958 2.646,1.542 false 2.24,1.958 2.333,1.521 false 2.281,4.104 2.344,3.615 false 2.698,4.125 2.625,3.594 false 0.688,4.094 0.948,3.344 false 1.406,4.135 1.198,3.344 false 0.156,0.094 0.469,0.292 0.313,0.198 10 false *a 0.167,0.323 0.479,0.521 0.313,0.198 10 false *A 0.208,2.271 0.521,2.469 0.313,0.198 10 false *B 0.344,2.583 0.656,2.781 0.313,0.198 10 false i1 0.302,0.656 0.615,0.854 0.313,0.198 10 false h1 1.906,0.677 2.375,0.938 0.469,0.26 10 false hO1 2.021,2.719 2.333,2.917 0.313,0.198 10 false iN1 0.99,0.479 1.302,0.677 0.313,0.198 10 false *b 2.396,0.74 2.708,0.938 0.313,0.198 10 false *c 2.396,2.813 2.708,3.01 0.313,0.198 10 false *c 0.969,2.583 1.281,2.781 0.313,0.198 10 false *b 0.479,1.979 0.792,2.177 0.313,0.198 10 false RR- 1.323,1.979 1.635,2.177 0.313,0.198 10 false RR+ 2.115,1.969 2.427,2.167 0.313,0.198 10 false RR+ 2.604,1.979 2.917,2.177 0.313,0.198 10 false RR- 0.594,4.125 0.906,4.323 0.313,0.198 10 false RL- 1.292,4.135 1.604,4.333 0.313,0.198 10 false RL+ 2.156,4.125 2.469,4.323 0.313,0.198 10 false RL+ 2.583,4.125 2.896,4.323 0.313,0.198 10 false RL-
*A for RH
*B for LH
*a Front view of skid control sensor wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the h1 or i1 rear speed sensor connector and the skid control sensor wire.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
h1-2 (RR+) - hO1-1 (RR+) Always Below 1 Ω
h1-2 (RR+) - hO1-2 (RR-) Always 10 kΩ or higher
h1-2 (RR+) - Body ground Always 10 kΩ or higher
h1-1 (RR-) - hO1-2 (RR-) Always Below 1 Ω
h1-1 (RR-) - hO1-1 (RR+) Always 10 kΩ or higher
h1-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
i1-2 (RL+) - iN1-1 (RL+) Always Below 1 Ω
i1-2 (RL+) - iN1-2 (RL-) Always 10 kΩ or higher
i1-2 (RL+) - Body ground Always 10 kΩ or higher
i1-1 (RL-) - iN1-2 (RL-) Always Below 1 Ω
i1-1 (RL-) - iN1-1 (RL+) Always 10 kΩ or higher
i1-1 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)

NG

11.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A28-22 (RR+) - hO1-1 (RR+) Always Below 1 Ω
A28-22 (RR+) - Body ground Always 10 kΩ or higher
A28-9 (RR-) - hO1-2 (RR-) Always Below 1 Ω
A28-9 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A28-20 (RL+) - iN1-1 (RL+) Always Below 1 Ω
A28-20 (RL+) - Body ground Always 10 kΩ or higher
A28-7 (RL-) - iN1-2 (RL-) Always Below 1 Ω
A28-7 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)
a.
C213978C10
0.271,1.031 0.677,1.292 0.406,0.26 1.708,1.031 2.115,1.292 0.406,0.26 1.198,2.031 1.333,2.5 false 2.615,2.031 2.813,2.5 false 0.25,0.219 0.49,0.396 0.24,0.177 10 false *a 1.219,2.563 1.573,2.719 0.354,0.156 10 false RR+ 2.719,2.542 3.01,2.698 0.292,0.156 10 false RL+ 0.365,1.073 1.104,1.427 0.74,0.354 10 false hO1 1.833,1.073 2.396,1.438 0.563,0.365 10 false iN1
*a Front view of wire harness connector
(to Skid Control Sensor Wire)


Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
hO1-1 (RR+) - Body ground Power switch on (IG) 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
iN1-1 (RL+) - Body ground Power switch on (IG) 5.7 to 14 V



Result:
Proceed to
OK
NG



OK

13.RECONFIRM DTC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

13.RECONFIRM DTC
a.

Turn the power switch off.


b.

Reconnect the h1 or i1 rear speed sensor connector and the skid control sensor wire.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the power switch on (READY).


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1238/38 and/or C1239/39 are output. A
DTCs C1238/38 and C1239/39 are not output. B



A

14.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

B

14.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
a.

Turn the power switch off.


b.

Replace the rear speed sensor rotor with rear speed sensor (rear axle hub and bearing assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL

HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
NEXT



NEXT

15.RECONFIRM DTC
15.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch on (READY).


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1238/38 and/or C1239/39 are output. A
DTCs C1238/38 and C1239/39 are not output. B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

END