Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1256/56  Accumulator Low Pressure  


DESCRIPTION

The accumulator pressure sensor is built into the brake actuator (brake booster with master cylinder assembly) and detects the accumulator pressure.

The skid control ECU turns on the brake warning light / red (malfunction) and brake warning light / yellow (minor malfunction), and sounds the meter buzzer if it senses a decrease in the accumulator pressure.

DTC C1256/56 may be stored if the accumulator pressure drops due to frequent braking (this is not a malfunction).

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1256/56 Accumulator Low Pressure 341 Significant drop in accumulator pressure continues.
(DTCs will be stored and the buzzer will operate when either condition is met.)
·

Accumulator pressure dropped due to frequent brake pedal operation (not a malfunction)

·

Pump motor malfunction

·

Accumulator deterioration

·

Accumulator pressure sensor (Brake booster with master cylinder assembly)

·

Supply voltage reduced


Electronically controlled brake system DTC

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


HINT:

When C1202/68, C1241/41, C1252/52, C1253/53 and/or C1391/69 are output together with C1256/56, inspect and repair the trouble areas indicated by C1202/68, C1241/41, C1252/52, C1253/53 and/or C1391/69 first.

for C1202/68: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1202/68

for C1241/41: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1241/41

for C1252/52 and C1253/53: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1252/52

for C1391/69: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1391/69


PROCEDURE

1.BRAKE PROBLEM CHECK
a.

Ask the customer if frequent braking was performed while the brake warning light / yellow (minor malfunction) was on.

Result:
Result Proceed to
Frequent braking was not performed. A
Frequent braking was performed. B


HINT:

This DTC may be stored even if the accumulator pressure drops only temporarily due to frequent braking.




A

2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY

B

END

2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
a.
C156574C15
1.656,1.177 2.052,1.427 0.396,0.25 0.885,1.177 1.281,1.427 0.396,0.25 1.01,1.927 0.708,2.969 false 1.198,1.906 1.458,2.969 false 2.427,0.813 1.927,1.875 false 1.344,0.813 1.74,1.844 false 2.188,0.615 2.667,0.781 0.479,0.167 10 false GND2 0.479,2.979 0.896,3.146 0.417,0.167 10 false GND1 1.302,2.979 1.656,3.135 0.354,0.156 10 false BM1 1.156,0.615 1.531,0.771 0.375,0.156 10 false BM2 0.333,0.292 0.615,0.688 0.281,0.396 10 false *a 1.75,1.219 2.156,1.542 0.406,0.323 10 false A47 0.979,1.219 1.438,1.458 0.458,0.24 10 false A46
*a Component without harness connected
(Brake Booster Pump Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the A46 and A47 brake booster pump assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A46-1 (BM1) - A46-2 (GND1) Always Below 10 Ω
A47-2 (BM2) - A47-1 (GND2) Always Below 10 Ω
A46-1 (BM1) - A47-2 (BM2) Always Below 1 Ω
A46-2 (GND1) - A47-1 (GND2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (ACCUMULATOR PRESSURE SENSOR)

NG

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

3.READ VALUE USING INTELLIGENT TESTER (ACCUMULATOR PRESSURE SENSOR)
a.

Reconnect the A46 and A47 brake booster pump assembly connectors.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Data List on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Accumulator Sensor Accumulator pressure sensor Min.: 0.00 V, Max.: 5.00 V Specified value: 2.90 to 4.20 V When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > ABS/VSC/TRC > Data List
Tester Display
Accumulator Sensor
50003 105 13

e.

Wait for 30 seconds without depressing the brake pedal.


f.

Check that the accumulator pressure sensor output value change is within the specified range.

OK:

Accumulator pressure sensor output value change is less than 0.55 V.



Result:
Proceed to
OK
NG



OK

NG

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SOLENOID VALVE)
4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SOLENOID VALVE)
a.

Select the Active Test on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

HINT:

The Active Test can be performed when the following conditions are met.

·

ABS main relay is on.

·

Shift lever is in P.

·

Parking brake is applied.

·

Vehicle speed is 0 km/h (0 mph).



Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Solenoid (SMC/SRC/SCC) Switching solenoid valve (SMC/SRC/SCC) Solenoid ON/OFF
·

Operation sound of solenoid (clicking sound) can be heard

·

ECB: Electronically Controlled Brake System


Chassis > ABS/VSC/TRC > Active Test
Tester Display
ECB Solenoid (SMC/SRC/SCC)
50004 105 89

b.

Perform the Active Test of the solenoid using the intelligent tester.


c.

Select the Data List on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed
Chassis > ABS/VSC/TRC > Data List
Tester Display
Wheel Cylinder Pressure Sensor
50003 105 308

d.

Check that the output value of the wheel cylinder pressure sensor does not increase.

OK:

The output value of the wheel cylinder pressure sensor does not increase.


HINT:

If the output value increases, there may be brake fluid leaks in the brake actuator.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY