Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › from 2015.04
RM2040EQ _52 Drivetrain _014703 AXLE AND DIFFERENTIAL _0074958 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43502E 1.INSTALL FRONT AXLE HUB BEARING

a.
C167714N05
1.094,1.823 2.427,1.969 2.427,1.969 1.302,2.073 false 2.604,0.708 2.365,0.708 2.365,0.708 2.531,1.156 false 2.479,1.885 2.885,2.146 0.406,0.26 10 false SST 2.073,0.625 2.406,0.844 0.333,0.219 10 false SST

Using SST and a press, install a new front axle hub bearing to the steering knuckle.

SST
09950-60020  (09951-00810)
09950-70010  (09951-07100)


Hide 47782 2.INSTALL FRONT DISC BRAKE DUST COVER

a.

Install the front disc brake dust cover to the steering knuckle with the 4 bolts.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


Hide 43502C 3.INSTALL FRONT AXLE HUB SUB-ASSEMBLY

a.
C197764N04
2.552,1 2.417,0.771 2.417,0.771 2.615,0.771 false 1.302,2.771 1.813,2.771 false 1.021,1.615 0.458,1.323 0.458,1.323 0.948,2.031 false 2.49,2.063 2.49,2.417 false 2.125,0.677 2.49,0.917 0.365,0.24 10 false SST 0.177,1.229 0.583,1.469 0.406,0.24 10 false SST 2.354,2.438 2.75,2.688 0.396,0.25 10 false SST 1.854,2.688 2.24,2.927 0.385,0.24 10 false SST

Using SST and a press, install the front axle hub sub-assembly to the steering knuckle.

SST
09608-32010  
09950-60010  (09951-00610)
09950-70010  (09951-07100)


Hide 43502G 4.INSTALL FRONT AXLE HUB HOLE SNAP RING

a.

Using snap ring pliers, install a new front axle hub hole snap ring.


Hide 43246B 5.INSTALL FRONT NO. 1 WHEEL BEARING DUST DEFLECTOR

a.

Set a new front No. 1 wheel bearing dust deflector to the steering knuckle while aligning the cutout for the speed sensor in the front No. 1 wheel bearing dust deflector with the hole of the steering knuckle.


b.
C265516N02
2.813,1.448 2.979,1.448 false 2.51,2.25 2.365,1.896 2.365,1.896 2.688,2.146 false 2.438,2.948 1.917,2.823 1.917,2.823 2.677,2.438 false 0.604,1.448 0.896,1.448 false 0.354,3 0.854,3 false 3.01,1.375 3.385,1.656 0.375,0.281 10 false SST 2.073,1.823 2.49,2.052 0.417,0.229 10 false SST 1.625,2.76 2.063,3.021 0.438,0.26 10 false SST 0.323,1.385 0.781,1.667 0.458,0.281 10 false SST 0.073,2.927 0.479,3.198 0.406,0.271 10 false SST

Using SST and a hammer, install the front No. 1 wheel bearing dust deflector.

SST
09316-60011  (09316-00011)
09608-32010  
09950-60010  (09951-00500, 09952-06010)
09950-60020  (09951-00810)


Hide 6.INSTALL FRONT AXLE ASSEMBLY

a.

Install the front axle assembly to the front shock absorber assembly with the 2 bolts and 2 nuts.

Torque:
290 N*m (2957 kgf*cm, 214 ft.*lbf)

NOTICE:

When installing the nuts, keep the bolts from rotating.



Hide 43420 7.INSTALL FRONT DRIVE SHAFT ASSEMBLY

a.
C238968C07
2.875,0.646 2.604,0.646 2.604,0.646 2.604,1.656 false 3.052,1 2.615,1 false 2.521,1.646 2.792,1.938 0.271,0.292 10 false *a
*a Matchmark


Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.

NOTICE:

Be careful not to damage the drive shaft boot or speed sensor rotor.



Hide 48069 8.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

a.

Connect the front lower No. 1 suspension arm sub-assembly to the front lower ball joint assembly with the bolt and 2 nuts.

Torque:
75 N*m (765 kgf*cm, 55 ft.*lbf)


Hide 45470 9.CONNECT TIE ROD ASSEMBLY

Hide 43512 10.INSTALL FRONT DISC

Hide 11.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43502H 12.INSTALL FRONT AXLE SHAFT NUT

a.

Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using a non-residue solvent.

NOTICE:
·

Be sure to perform this work even, when using a new front drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.

Using a socket wrench (30 mm), install the front axle shaft nut.

Torque:
294 N*m (2998 kgf*cm, 217 ft.*lbf)

NOTICE:

Stake the nut after inspecting for looseness and runout in the following steps.


HINT:

Keep depressing the brake pedal to prevent the front drive shaft from rotating.



Hide 13.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43512 14.REMOVE FRONT DISC

Hide 15.INSPECT FRONT AXLE HUB BEARING LOOSENESS

Hide 43512 17.INSTALL FRONT DISC

Hide 18.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 89543 19.INSTALL FRONT SPEED SENSOR

a.

Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt and clamp.

Torque:
19 N*m (192 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not twist the front speed sensor when installing it.


HINT:

Install the speed sensor harness bracket first and then the front flexible hose.



b.

Install the front speed sensor to the steering knuckle with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not twist the front speed sensor when installing it.



Hide 43502H 20.STAKE FRONT AXLE SHAFT NUT

a.
C242433

Using a chisel and a hammer, stake the front axle shaft nut.


Hide 21.INSTALL FRONT WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 22.CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

a.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER>INSTALLATION


b.

Connect the reservoir level switch connector.



Hide 55702A 23.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 24.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 25.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT