1. PRECAUTION
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
64718C
2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER
3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67913
4.REMOVE FRONT DOOR SCUFF PLATE RH
62111A
5.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
62311B
6.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Disconnect the front door opening trim weatherstrip RH.
55317A
7.REMOVE INSTRUMENT SIDE PANEL RH
Using a moulding remover, disengage the 4 claws as shown in the illustration.
Disengage the 3 guides and remove the instrument side panel RH as shown in the illustration.
55431B
8.REMOVE UPPER INSTRUMENT PANEL FINISH PANEL
Disengage the 4 clips as shown in the illustration.
Disconnect the connector to remove the upper instrument panel finish panel.
55670
9.REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY
| *1 | Protective Tape |
Apply protective tape to the area shown in the illustration.
Disengage the 2 clips as shown in the illustration.
Using a moulding remover, disengage the 2 clips to remove the No. 3 instrument panel register assembly.
55410C
10.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.
Using a moulding remover, disengage the 2 claws, 4 clips and 2 guides.
Disengage the 5 claws, 5 clips and 2 guides.
Disconnect each connector.
Remove the instrument cluster finish panel assembly as shown in the illustration.
83100
11.REMOVE COMBINATION METER ASSEMBLY
53921B
12.REMOVE FRONT PANEL GARNISH RH
Disengage the claw, 5 clips and 6 guides to remove the front panel garnish RH.
53601
13.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
14.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Remove the 2 bolts <B>.
Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.
53922B
15.REMOVE FRONT PANEL GARNISH LH
Disengage the claw, 5 clips and 6 guides to remove the front panel garnish LH.
33504F
16.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.
58805C
17.REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY
Open the upper console panel sub-assembly door.
Move the shift lever to N.
Disengage the 4 clips.
Disconnect each connector and remove the rear console upper panel sub-assembly.
58801E
18.REMOVE UPPER CONSOLE BOX SUB-ASSEMBLY
58864B
19.REMOVE NO. 4 CONSOLE BOX DUCT
58815A
20.REMOVE CONSOLE BOX CARPET
21.REMOVE REAR CONSOLE BOX ASSEMBLY
22.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.
Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.
Disengage the 3 claws and 2 clips as shown in the illustration.
Disengage the clamp.
Disconnect the connector to remove the center instrument cluster finish panel assembly.
55660
23.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Pull the No. 2 instrument panel register assembly as shown in the illustration to disengage the 6 clips and remove the No. 2 instrument panel register assembly.
58916
24.REMOVE BOX BOTTOM MAT
Remove the box bottom mat.
58804A
25.REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY
Remove the 2 screws <C> or <D>.
Disengage the 4 clips and guide as shown in the illustration.
Disconnect each connector to remove the upper console panel sub-assembly.
26.REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)
27.REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System)
55510F
28.REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY
Disengage the 8 clips as shown in the illustration.
Disconnect the connector to remove the No. 1 speaker opening cover assembly.
86160J
29.REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)
67914
30.REMOVE FRONT DOOR SCUFF PLATE LH
Use the same procedure as for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62112A
31.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Use the same procedure as for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62312B
32.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Disconnect the front door opening trim weatherstrip LH.
55318C
33.REMOVE INSTRUMENT SIDE PANEL LH
Using a moulding remover, disengage the 4 claws as shown in the illustration.
Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.
55607
34.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Disengage the 4 claws and 2 guides.
Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.
55303B
35.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Remove the bolt <B> and screw <C> or <D>.
Open the lower instrument panel door.
Remove the 3 screws <C> or <D>.
Disengage the 2 clips and 4 guides and remove the lower instrument panel sub-assembly.
55475A
36.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
Disengage the 5 clips to remove the No. 2 instrument cluster finish panel garnish as shown in the illustration.
55650
37.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
| *1 | Protective Tape |
Apply protective tape to the area shown in the illustration.
Disengage the 2 clips as shown in the illustration.
Using a moulding remover, disengage the 2 clips to remove the No. 1 instrument panel register assembly.
62211
38.REMOVE FRONT PILLAR GARNISH RH
55409F
39.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
| *1 | Protective Tape |
Apply protective tape to the area shown in the illustration.
Using a moulding remover, disengage the 2 clips and 3 claws.
Disengage the 2 guides to remove the No. 2 instrument panel speaker panel sub-assembly.
86160P
40.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)
62212
41.REMOVE FRONT PILLAR GARNISH LH
Use the same procedure as for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
55408F
42.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
| *1 | Protective Tape |
Apply protective tape to the area shown in the illustration.
Using a moulding remover, disengage the 2 clips and 3 claws.
Disengage the 2 guides to remove the No. 1 instrument panel speaker panel sub-assembly.
86160P
43.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
Use the same procedure as for the RH side.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
55480D
44.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Disengage the 4 clips and guide and remove the lower instrument panel finish panel assembly.
58816B
45.REMOVE CONSOLE BOX INSERT
Remove the 2 screws <C> or <D>.
Disengage the clip and 3 guides to remove the console box insert as shown in the illustration.
Disengage the 2 claws to disconnect the room temperature sensor from the console box insert.
58817A
46.REMOVE FRONT NO. 2 CONSOLE BOX INSERT
Remove the 2 screws <C> or <D>.
Disengage the clip and 3 guides to remove the front No. 2 console box insert as shown in the illustration.
55011A
47.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
Disengage the 10 clips to remove the No. 1 instrument panel garnish sub-assembly as shown in the illustration.
82142A
48.DISCONNECT NO. 2 INSTRUMENT PANEL WIRE
49.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
Disconnect each connector.
Disengage each clamp.
Remove the 2 passenger airbag bolts <A>.
| *1 | Passenger Airbag Bolt <A> | *2 | Bolt <B> |
| *3 | Nut <E> | *4 | Clip |
Remove the 3 bolts <B> and nut <E>.
Remove the 2 clips.
Disengage the 5 guides and remove the instrument panel safety pad assembly as shown in the illustration.
Do not damage the instrument panel safety pad assembly.
Do not allow the wire harnesses to interfere with the surrounding parts.