DTC P3190 Poor Engine Power |
DTC P3191 Engine does not Start |
| DTC No. | DTC Detection Condition | Trouble Area |
| P3190 | When all of the following conditions are met (1 trip detection logic):
|
|
| P3191 | When all of the following conditions are met (1 trip detection logic):
|
|
| ECM (Powertrain / Engine and ECT / Data List) | |||
| HV Target Engine Speed | Engine Speed | Requested Engine Torque | Actual Engine Torque |
| Throttle Position Command | Throttle Position No. 1 | Calculate Load | Coolant Temp |
| Short FT #1 | Long FT #1 | - | - |
| POWER MANAGEMENT CONTROL ECU (Powertrain / Hybrid Control / Data List) | |||
| Target Engine Rev | Engine Revolution | Requested Engine Torque | Engine Coolant Temp |
| Engine Idling Request | - | - | - |
| Frequency of Operation | Continuous |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P3190, P3191 AND/OR P3193) |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P3190 or P3191 is output | A |
| DTC P3193 is output | B |
| DTC P3190, P3191 and/or P3193 and other DTCs are output | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK SHORTAGE OF FUEL |
Check the amount of fuel remaining.
|
| ||||
| OK | |
| 3.CLEAR DTC |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
| NEXT | |
| 4.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 5.CHECK FOR UNUSUAL NOISE OR VIBRATION WHEN STARTING ENGINE OR REVVING UP |
|
| ||||
| OK | |
| 6.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 7.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY |
Inspect the throttle with motor body assembly (Click here).
|
| ||||
| OK | |
| 8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY |
Inspect the mass air flow meter sub-assembly (Click here).
|
| ||||
| OK | |
| 9.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
| ||||
| OK | |
| 10.INSPECT CRANKSHAFT POSITION SENSOR |
Inspect the crankshaft position sensor (Click here).
|
| ||||
| OK | |
| 11.REPLACE CAMSHAFT POSITION SENSOR |
Replace the camshaft position sensor (Click here).
| NEXT | |
| 12.CHECK WHETHER DTC OUTPUT RECURS (DTC P3190 OR P3191) |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (READY).
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P3190 or P3191 is output | A |
| DTCs are not output | B |
|
| ||||
| A | |
| 13.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION) |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / All Data / MAP and Throttle Idle Position.
Confirm that Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| MAP (Data List) | (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 14.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | |
| 15.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (READY).
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| NEXT | ||
| ||