Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows)

POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows) > Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.
If power window initialization has not been performed, the auto up and down function will not operate (Click here).

WIRING DIAGRAM


B185318E01


INSPECTION PROCEDURE

NOTICE:
  1. The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (Click here).
  2. If the power window regulator motor assembly (for driver door) has been replaced with a new one, initialize the power window control system (Click here).
  3. Check that the "D Window Auto Up" and "D Window Auto Down" power window control system customize settings are "ON" before proceeding with work (Click here).
  4. After the catch protection function operates, the auto up function will not operate the first time power window auto up switch is operated. The auto up function will operate normally after the first power window switch operation.

HINT:
If the pulse sensor built into the power window regulator motor assembly (for driver door) is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator master switch assembly at the auto up position, and opened manually by pushing down the power window regulator master switch assembly (Click here).

1.READ VALUE USING GTS (MASTER SWITCH)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Master switch / Data List.

  1. Read the Data List according to the display on the GTS.

    Master Switch 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Auto SW
    Driver door power window auto switch signal / OFF or ON
    OFF: Driver door power window auto switch not being operated
    ON: Driver door power window auto switch being operated
    -

    OK:
    On the GTS screen, ON or OFF is displayed accordingly.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


2.READ VALUE USING GTS (D-DOOR MOTOR)
  1. Enter the following menus: Body Electrical / D-Door Motor / Data List.

  1. Read the Data List according to the display on the GTS.

    D-Door Motor 
    Tester Display
    Measurement Item
    Normal Condition
    Diagnostic Note
    D Door P/W Auto SW
    Driver door power window auto switch signal / OFF or ON
    OFF: Driver door power window auto switch not being operated
    ON: Driver door power window auto switch being operated
    -

    OK:
    On the GTS screen, ON or OFF is displayed accordingly.



NG
Go to step 5
OK


3.PERFORM INITIALIZATION (FOR DRIVER DOOR)
  1. Initialize the power window regulator motor assembly (for driver door) (Click here).


NEXT


4.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)
  1. Check that the driver door power window moves when the auto up and down function of the power window regulator master switch assembly is operated (Click here).

    OK:
    Driver door auto up and down function is normal.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) (Click here)
OK

END (PROBLEM DUE TO INITIALIZATION FAILURE) 

5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
  1. Replace the power window regulator master switch assembly (Click here).


NEXT


6.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)
  1. Check that the driver door power window moves when the auto up and down function of the power window regulator master switch assembly is operated (Click here).

    OK:
    Driver door auto up and down function is normal.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) (Click here)
OK

END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE)