Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows)

POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows) > Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.
If power window initialization has not been performed, the auto up and down function will not operate (Click here).

WIRING DIAGRAM


B342108E07


INSPECTION PROCEDURE

NOTICE:
  1. If the power window regulator motor assembly (for front passenger door) has been replaced with a new one, initialize the power window control system (Click here).
  2. Check that the "P Window Auto Up" and "P Window Auto Down" power window control system customize settings are "ON" before proceeding with work (Click here).
  3. After the catch protection function operates, the auto up function will not operate the first time power window auto up switch is operated. The auto up function will operate normally after the first power window switch operation.

HINT:
If the pulse sensor built into the power window regulator motor assembly (for front passenger door) is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator switch assembly at the auto up position, and opened manually by pushing down the power window regulator switch assembly (Click here).

1.READ VALUE USING GTS (P-DOOR MOTOR)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / P-Door Motor / Data List.

  1. Read the Data List according to the display on the GTS.

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Auto SW
    Front Passenger door power window auto switch signal / OFF or ON
    OFF: Front passenger door power window auto switch not being operated
    ON: Front passenger door power window auto switch being operated
    -

    OK:
    On the GTS screen, ON or OFF is displayed accordingly.



NG
Go to step 4
OK


2.PERFORM INITIALIZATION (FOR FRONT PASSENGER DOOR)
  1. Initialize the power window regulator motor assembly (for front passenger door) (Click here).


NEXT


3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)
  1. Check that the front passenger door power window moves when the auto up and down function of the power window regulator switch assembly is operated (Click here).

    OK:
    Front passenger door auto up and down function is normal.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)
OK

END (PROBLEM DUE TO INITIALIZATION FAILURE) 

4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
  1. Remove the power window regulator switch assembly. (Click here).

  1. Inspect the power window regulator switch assembly (Click here).



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR))
  1. Disconnect the J9 power window regulator motor assembly (for front passenger door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J12-8 (AUTO) - J9-4 (AUTO)
    Always
    Below 1 Ω
    J12-8 (AUTO) or J9-4 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)