Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

DTC    B1507    Open in Turn Signal Circuit

DTC    B1508    Short in Turn Signal / Hazard Flasher Circuit

for Preparation Click here


DESCRIPTION

These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1507
When IG voltage is 9.5 V or more and the following condition is detected:
  1. Open in turn signal light circuit
  1. Bulb
  2. Harness or connector
  3. Instrument panel junction block assembly
  4. Outer mirror control ECU assembly LH*
  5. Outer mirror control ECU assembly RH*
  6. Combination meter assembly
B1508
When IG voltage is 9.5 V or more and the following condition is detected:
  1. Short in turn signal light circuit or hazard warning light circuit
  1. Bulb
  2. Harness or connector
  3. Instrument panel junction block assembly
  4. Outer mirror control ECU assembly LH*
  5. Outer mirror control ECU assembly RH*
  6. Combination meter assembly
  1. *: w/ Seat Position Memory

WIRING DIAGRAM


w/ Seat Position Memory

E237287E12


w/o Seat Position Memory

E305980E06


INSPECTION PROCEDURE

NOTICE:
Inspect the bulbs for this system before performing the following inspection procedure.
  1. Front turn signal light assembly (for TMMK Made): Click here
  2. Side turn signal light assembly (for TMMK Made): Click here
  3. Side turn signal light assembly (except TMMK Made): Click here
  4. Rear combination light assembly (for TMMK Made): Click here
  5. Rear combination light assembly (except TMMK Made): Click here

1.INSPECT LIGHTS
  1. Inspect the illumination of each turn signal light.

    Result:
    Result
    Proceed to
    Turn signal lights for one side do not illuminate.
    A
    Front turn signal light does not illuminate.
    B
    Rear turn signal light does not illuminate.
    C
    Side turn signal light does not illuminate*1.
    D
    Side turn signal light does not illuminate*2.
    E

    1. *1: w/ Seat Position Memory
    2. *2: w/o Seat Position Memory



B
Go to step 4

C
Go to step 9

D
Go to step 11

E
Go to step 14
A


2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the I17 combination meter assembly connector.

  1. Disconnect the 3A instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LH 
    Tester Connection
    Condition
    Specified Condition
    I17-7 (LL) - 3A-20
    Always
    Below 1 Ω
    for RH 
    Tester Connection
    Condition
    Specified Condition
    I17-13 (LR) - 3A-37
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LH 
    Tester Connection
    Condition
    Specified Condition
    I17-7 (LL) - Body ground
    Always
    10 kΩ or higher
    for RH 
    Tester Connection
    Condition
    Specified Condition
    I17-13 (LR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (Click here).


E225578E02

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    3A-20 - 3D-10
    Always
    Below 1 Ω
    3A-20 - 3C-22
    Always
    Below 1 Ω
    3A-20 - 3A-40
    Always
    Below 1 Ω
    for RH:
    Tester Connection
    Condition
    Specified Condition
    3A-37 - 3D-5
    Always
    Below 1 Ω
    3A-37 - 3C-19
    Always
    Below 1 Ω
    3A-37 - 3B-32
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

4.CONFIRM VEHICLE TYPE
  1. Choose the model to be inspected.

    Result:
    Result
    Proceed to
    except TMMK Made
    A
    for TMMK Made
    B



B
Go to step 7
A


5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the A23*1 or A65*2 headlight assembly connector.

    1. *1: for LH
    2. *2: for RH

  1. Disconnect the 3D instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LH 
    Tester Connection
    Condition
    Specified Condition
    A23-2 (B) - 3D-10
    Always
    Below 1 Ω
    A23-1 (E) - Body ground
    Always
    Below 1 Ω
    for RH 
    Tester Connection
    Condition
    Specified Condition
    A65-2 (B) - 3D-5
    Always
    Below 1 Ω
    A65-1 (E) - Body ground
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LH 
    Tester Connection
    Condition
    Specified Condition
    A23-2 (B) - Body ground
    Always
    10 kΩ or higher
    for RH 
    Tester Connection
    Condition
    Specified Condition
    A65-2 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (Click here).


E263616E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    3A-20 - 3D-10
    Always
    Below 1 Ω
    for RH:
    Tester Connection
    Condition
    Specified Condition
    3A-37 - 3D-5
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE HEADLIGHT ASSEMBLY (Click here)  

7.CHECK HARNESS AND CONNECTOR (FRONT TURN SIGNAL LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the A92*1 or A96*2 front turn signal light assembly connector.

    1. *1: for LH
    2. *2: for RH

  1. Disconnect the 3D instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LH 
    Tester Connection
    Condition
    Specified Condition
    A92-3 (B) - 3D-10
    Always
    Below 1 Ω
    A92-6 (E) - Body ground
    Always
    Below 1 Ω
    for RH 
    Tester Connection
    Condition
    Specified Condition
    A96-3 (B) - 3D-5
    Always
    Below 1 Ω
    A96-6 (E) - Body ground
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LH 
    Tester Connection
    Condition
    Specified Condition
    A92-3 (B) - Body ground
    Always
    10 kΩ or higher
    for RH 
    Tester Connection
    Condition
    Specified Condition
    A96-3 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (Click here).


E263616E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    3A-20 - 3D-10
    Always
    Below 1 Ω
    for RH:
    Tester Connection
    Condition
    Specified Condition
    3A-37 - 3D-5
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE FRONT TURN SIGNAL LIGHT ASSEMBLY (Click here)  

9.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the T8*1 or T13*2 rear combination light assembly connector.

    1. *1: for LH
    2. *2: for RH

  1. Disconnect the 3C instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LH 
    Tester Connection
    Condition
    Specified Condition
    T8-1 (B) - 3C-22
    Always
    Below 1 Ω
    T8-2 (E) - Body ground
    Always
    Below 1 Ω
    for RH 
    Tester Connection
    Condition
    Specified Condition
    T13-1 (B) - 3C-19
    Always
    Below 1 Ω
    T13-2 (E) - Body ground
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LH 
    Tester Connection
    Condition
    Specified Condition
    T8-1 (B) - Body ground
    Always
    10 kΩ or higher
    for RH 
    Tester Connection
    Condition
    Specified Condition
    T13-1 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (Click here).


E263618E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    3A-20 - 3C-22
    Always
    Below 1 Ω
    for RH:
    Tester Connection
    Condition
    Specified Condition
    3A-37 - 3C-19
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY (Click here)  

11.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the K12*1 or J10*2 outer mirror control ECU assembly connector.

    1. *1: for LH
    2. *2: for RH

  1. Disconnect the 3A*1 or 3B*2 instrument panel junction block assembly connector.

    1. *1: for LH
    2. *2: for RH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LH 
    Tester Connection
    Condition
    Specified Condition
    K12-11 (TRNI) - 3A-40
    Always
    Below 1 Ω
    for RH 
    Tester Connection
    Condition
    Specified Condition
    J10-11 (TRNI) - 3B-32
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LH 
    Tester Connection
    Condition
    Specified Condition
    K12-11 (TRNI) - Body ground
    Always
    10 kΩ or higher
    for RH 
    Tester Connection
    Condition
    Specified Condition
    J10-11 (TRNI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (Click here).


    E263617E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    3A-20 - 3A-40
    Always
    Below 1 Ω
    for RH:
    Tester Connection
    Condition
    Specified Condition
    3A-37 - 3B-32
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


13.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY
  1. Remove the outer mirror control ECU assembly with a new or known good one (Click here).

  1. Recheck for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs are not output.
    A
    DTCs are output (for TMMK Made).
    B
    DTCs are output (except TMMK Made).
    C



B
REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY (Click here)

C
REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY (Click here)
A

END 

14.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the K7*1 or J7*2 side turn signal light assembly connector.

    1. *1: for LH
    2. *2: for RH

  1. Disconnect the 3A*1 or 3B*2 instrument panel junction block assembly connector.

    1. *1: for LH
    2. *2: for RH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LH 
    Tester Connection
    Condition
    Specified Condition
    K7-10 (B) - 3A-40
    Always
    Below 1 Ω
    K7-11 (-) - Body ground
    Always
    Below 1 Ω
    for RH 
    Tester Connection
    Condition
    Specified Condition
    J7-10 (B) - 3B-32
    Always
    Below 1 Ω
    J7-11 (-) - Body ground
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LH 
    Tester Connection
    Condition
    Specified Condition
    K7-10 (B) - Body ground
    Always
    10 kΩ or higher
    for RH 
    Tester Connection
    Condition
    Specified Condition
    J7-10 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (Click here).


    E263617E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    3A-20 - 3A-40
    Always
    Below 1 Ω
    for RH:
    Tester Connection
    Condition
    Specified Condition
    3A-37 - 3B-32
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY (Click here)