DTC P013613 O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open |
DTC P013617 O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Above Threshold |
DTC P01361C O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Out of Range |

| DTC No. | DTC Detection Condition | Trouble Area |
| P013613 | Abnormal voltage output: During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):
|
|
| P013617 | Low voltage (open): During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):
|
|
| P01361C | High voltage (short): During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):
|
|
| Active Air Fuel Ratio Control |
| Abnormal Voltage Output of Heated Oxygen Sensor (DTC P013613) |

| Open or Short in Heated Oxygen Sensor Circuit (DTC P013617 or P01361C) |

| Required Sensors/Components (Main) | Heated oxygen sensor (sensor 2) |
| Required Sensors/Components (Related) | Crankshaft position sensor Engine coolant temperature sensor Mass air flow meter sub-assembly Throttle position sensor Air fuel ratio sensor |
| Frequency of Operation | Once per driving cycle |
| Active air fuel ratio control | Executing |
| Active air fuel ratio control begins when all of following conditions met: | - |
| Battery voltage | 11 V or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Idling | Off |
| Engine speed | Less than 4000 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10% or higher, and less than 90% |
| Either of following conditions is met | 1 or 2 |
| 1. Both of following conditions are met | - |
| (a) Commanded air fuel ratio | 14.4 or less |
| (b) Heated oxygen sensor voltage | 0.21 V or higher, and less than 0.69 V |
| 2. Both of following conditions are met | - |
| (c) Commanded air fuel ratio | 14.8 or more |
| (d) Heated oxygen sensor voltage | 0.21 V or higher, and less than 0.69 V |
| Both of following conditions are met | - |
| (a) Commanded air fuel ratio | 14.4 or less |
| (b) Heated oxygen sensor voltage | Less than 0.21 V |
| Both of following conditions are met | - |
| (a) Commanded air fuel ratio | 14.8 or more |
| (b) Heated oxygen sensor voltage | Higher than 0.69 V |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| GTS Display (Sensor) | Injection Volume | Status | Voltage |
| A/F (O2) Sensor Voltage B1S1 (Air fuel ratio) | 12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2 Sensor Voltage B1S2 (Heated oxygen) | 12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |

| 1.READ OUTPUT DTC (DTC P013613, P013617 OR P01361C) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P01361C is output | A |
| DTC P013617 is output | B |
| DTC P013613 is output | C |
| DTC P013613, P013617 or P01361C and other DTCs are output | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING GTS (O2 SENSOR VOLTAGE B1S2) |
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / O2 Sensor Voltage B1S2.
Allow the engine to idle.
Read the heated oxygen sensor output voltage while idling.
| Heated Oxygen Sensor Output Voltage | Proceed to |
| 1.0 V or higher | A |
| Less than 1.0 V | B |
|
| ||||
| A | |
| 3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
![]() |
Disconnect the heated oxygen sensor connector.
| *a | Component without harness connected (Heated Oxygen Sensor) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 3 (OX1B) | Always | 10 kΩ or higher |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
Turn the engine switch off and wait for 5 minutes or more.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E96-17 (HT1B) - E96-99 (OX1B) | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.
Change the fuel injection volume using the GTS, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the GTS.
| GTS Display (Sensor) | Voltage Variation | Proceed to |
| A/F (O2) Sensor Voltage B1S1 (Air fuel ratio) | Alternates between higher than and less than 3.3 V | OK |
| Remains at higher than 3.3 V | NG | |
| Remains at less than 3.3 V |

|
| ||||
| OK | |
| 6.INSPECT AIR FUEL RATIO SENSOR |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Drive the vehicle at 60 km/h (37 mph) or more for 10 minutes or more.
Stop the vehicle.
Enter the following menus: Powertrain / Engine / Data List / All Data / A/F (O2) Sensor Current B1S1.
Drive the vehicle at 60 km/h (37 mph) or more and release the accelerator pedal for at least 5 seconds without depressing the brake pedal in oder to execute fuel-cut control. Perform this 3 times.

Read the value of the air fuel ratio sensor current while the fuel-cut operation is performed.
|
| ||||
|
| ||||
| 7.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / O2 Sensor Voltage B1S2.
Change the fuel injection volume using the GTS and monitor the voltage output of the heated oxygen sensor displayed on the GTS.
|
| ||||
| OK | |
| 8.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.
Change the fuel injection volume using the GTS, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the GTS.
| GTS Display (Sensor) | Voltage Variation | Proceed to |
| A/F (O2) Sensor Voltage B1S1 (Air fuel ratio) | Alternates between higher than and less than 3.3 V | OK |
| Remains at higher than 3.3 V | NG | |
| Remains at less than 3.3 V |

|
| ||||
| OK | |
| 9.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / All Data / Engine Speed and Intake Manifold Absolute Pressure.
Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stalls |
| Intake Manifold Absolute Pressure (Data List) | Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs) (150 to 300 mmHg(abs)) (EGR valve is fully closed) | Intake Manifold Absolute Pressure value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
| OK | ||
| ||
| 10.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | ||
| ||
| 11.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 12.PERFORM CONFIRMATION DRIVING PATTERN |
Perform Confirmation Driving Pattern.
| NEXT | |
| 13.CHECK WHETHER DTC OUTPUT RECURS (DTC P013613 OR P01361C) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P013613 or P01361C.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.
| Result | Proceed to |
| ABNORMAL (DTC P013613 or P01361C is output) | A |
| NORMAL (DTCs are not output) | B |
|
| ||||
| A | |
| 14.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / All Data / Engine Speed and Intake Manifold Absolute Pressure.
Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stalls |
| Intake Manifold Absolute Pressure (Data List) | Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs) (150 to 300 mmHg(abs)) (EGR valve is fully closed) | Intake Manifold Absolute Pressure value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
| OK | ||
| ||
| 15.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | ||
| ||
| 16.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 17.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Inspect the heated oxygen sensor (Click here).
|
| ||||
| OK | |
| 18.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E21-1 (HT1B) - E96-17 (HT1B) | Always | Below 1 Ω |
| E21-3 (OX1B) - E96-99 (OX1B) | Always | Below 1 Ω |
| E21-4 (E2) - E96-100 (EX1B) | Always | Below 1 Ω |
| E21-1 (HT1B) or E96-17 (HT1B) - Body ground and other terminals | Always | 10 kΩ or higher |
| E21-3 (OX1B) or E96-99 (OX1B) - Body ground and other terminals | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 19.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
| NEXT | |
| 20.PERFORM CONFIRMATION DRIVING PATTERN |
Perform Confirmation Driving Pattern.
| NEXT | |
| 21.CHECK WHETHER DTC OUTPUT RECURS (DTC P013613, P013617 OR P01361C) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P013613, P013617 or P01361C.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.
| Result | Proceed to |
| ABNORMAL (DTC P013613, P013617 or P01361C is output) | A |
| NORMAL (DTCs are not output) | B |
|
| ||||
| A | |
| 22.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / All Data / Engine Speed and Intake Manifold Absolute Pressure.
Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stalls |
| Intake Manifold Absolute Pressure (Data List) | Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs) (150 to 300 mmHg(abs)) (EGR valve is fully closed) | Intake Manifold Absolute Pressure value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
| OK | ||
| ||
| 23.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | ||
| ||