Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > Fuel Pump Control Circuit

for Preparation Click here


DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump and fuel pump control ECU assembly (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU assembly. Based on the signal sent from the ECM, the fuel pump control ECU adjust the fuel pump operation speed.

WIRING DIAGRAM


A338709E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE CIRCUIT RELAY)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

  1. Check whether operating sounds can be heard while operating the fuel pump using the GTS.

    OK:
    Operating sounds can be heard from the fuel pump.



NG
Go to step 7
OK


2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO, ACTIVATE THE CIRCUIT RELAY)


    A240046E01
  1. Remove the fuel pump (for low pressure side) from the fuel tank assembly (Click here).
    Text in Illustration 
    *a
    Component with harness connected
    (Fuel Pump [for Low Pressure Side])

  1. Clean the fuel pump to completely remove any remaining fuel.

  1. Connect the fuel pump connector.

    CAUTION:
    Make sure that there is no fuel remaining inside or on the outside of the fuel pump.

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio.

  1. Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    GTS Operation
    Specified Condition
    1 - 2
    Fuel pump duty ratio: 25%
    3.2 to 4.05 V
    Fuel pump duty ratio: 80%
    8.8 to 12.5 V

  1. Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

  1. Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    GTS Operation
    Specified Condition
    1 - 2
    ON (Fuel pump duty ratio: 90%)
    9.0 to 14.0 V

    HINT:
    1. Be sure to measure the voltage with all the connectors connected.
    2. Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).



NG
Go to step 9
OK


3.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)
  1. Inspect the fuel pump (for low pressure side) (Click here).



NG
Go to step 4
OK

END 

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
  1. Disconnect the fuel pump control ECU assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    N30-2 (FPC) - A84-21 (FPC)
    Always
    Below 1 Ω
    N30-2 (FPC) or A84-21 (FPC) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)
  1. Replace the fuel pump (for low pressure side) (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side) (Click here).


NEXT


6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check the fuel pump operation .

    OK:
    Malfunction has been repaired successfully.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

END 

7.INSPECT FUEL PUMP CONTROL ECU ASSEMBLY (POWER SOURCE VOLTAGE)


    A330727E01
  1. Disconnect the fuel pump control ECU assembly connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Pump Control ECU Assembly)

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    N30-1 (+B) - N30-4 (E)
    Engine switch on (IG)
    11 to 14 V



NG
Go to step 13
OK


8.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)
  1. Inspect the fuel pump (for low pressure side) (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side) (Click here).



NG
REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE) (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (FUEL PUMP (FOR LOW PRESSURE SIDE) - FUEL PUMP CONTROL ECU ASSEMBLY)
  1. Disconnect the fuel pump (for low pressure side) connector.

  1. Disconnect the fuel pump control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    N11-4 (B) - N30-6 (FP)
    Always
    Below 1 Ω
    N11-5 (E) - N30-5 (FP-)
    Always
    Below 1 Ω
    N11-4 (B) or N30-6 (FP) - Body ground and other terminals
    Always
    10 kΩ or higher
    N11-5 (E) or N30-5 (FP-) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
  1. Disconnect the fuel pump control ECU assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    N30-2 (FPC) - A84-21 (FPC)
    Always
    Below 1 Ω
    N30-2 (FPC) or A84-21 (FPC) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
  1. Replace the fuel pump control ECU assembly (Click here).


NEXT


12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check the fuel pump operation .

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END 

13.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)
  1. Disconnect the fuel pump control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    N30-4 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
  1. Disconnect the fuel pump control ECU assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    N30-2 (FPC) - A84-21 (FPC)
    Always
    Below 1 Ω
    N30-2 (FPC) or A84-21 (FPC) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.CHECK HARNESS AND CONNECTOR (EFI MAIN2 RELAY - FUEL PUMP CONTROL ECU ASSEMBLY)
  1. Disconnect the No. 1 integration relay connector.

  1. Disconnect the fuel pump control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1C-6 - N30-1 (+B)
    Always
    Below 1 Ω
    1C-6 or N30-1 (+B) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN2 RELAY)
  1. Inspect the EFI MAIN2 relay (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)