Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › CAMSHAFT
RM33A0E _51 Engine / Hybrid System _065333 2GR-FKS ENGINE MECHANICAL _0327366 CAMSHAFT A

2GR-FKS ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


PROCEDURE

Hide 1.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

a.
A377778C01
2.656,1.469 2.521,1.469 2.521,1.469 2.365,1.188 true 2.979,0.896 2.823,0.896 2.823,0.896 2.677,1.104 true 2.698,1.396 3.01,1.552 0.313,0.156 10 true *a 3.021,0.813 3.26,1 0.24,0.188 10 true *b
*a Timing Mark (Cutout)
*b "0" Timing Mark


Confirm that the timing mark (cutout) on the crankshaft pulley is aligned with the "0" timing mark of the timing chain cover assembly.


Hide 13050 2.SET CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 2)

HINT:

Perform Inspection After Repair after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A377809C01
1.896,0.219 2.125,0.219 2.125,0.219 2.885,0.927 true 2.792,1.021 2.771,1.781 2.771,1.781 2.875,1.052 true 2.708,1.792 3.021,1.948 0.313,0.156 10 false *a 1.708,0.146 2.021,0.302 0.313,0.156 10 false *b
*a Timing Mark
*b Mark Plate


Align the mark plate (yellow) with the timing mark of the camshaft timing gear assembly as shown in the illustration and install the No. 2 chain sub-assembly to the camshaft timing gear assembly.


b.
A377810C01
1.302,1.188 1.583,0.917 1.583,0.917 1.823,0.917 true 1.854,0.844 2.167,1 0.313,0.156 10 true *a
*a Place on camshaft timing gear assembly


Install the chain sub-assembly to the camshaft timing gear assembly, and then set the camshaft timing gear assembly to the camshaft housing sub-assembly LH.

HINT:
·

Place the chain sub-assembly on the camshaft timing gear assembly but do not engage the teeth of the sprocket and the chain sub-assembly.

·

Be sure to install the camshaft timing gear assembly with the timing mark facing upward.




Hide 13070A 3.SET CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 2)

HINT:

Perform Inspection After Repair after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A377811C01
2.771,3.167 2.771,2.49 true 2.74,2.115 2.917,1.5 2.917,1.5 2.823,2.115 true 2.958,1.417 3.271,1.573 0.313,0.156 10 true *a 2.719,3.188 3.031,3.344 0.313,0.156 10 true *b
*a Timing Mark
*b Mark Plate


Align the mark plate (yellow) with the timing mark of the camshaft timing exhaust gear assembly as shown in the illustration and install the No. 2 chain sub-assembly to the camshaft timing exhaust gear assembly.


b.

Set the camshaft timing exhaust gear assembly to the camshaft housing sub-assembly LH.


Hide 13560A 4.SET NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A377803

While lifting up the camshaft timing exhaust gear assembly, pass the No. 3 chain tensioner assembly through the No. 2 chain sub-assembly and set it in place.

NOTICE:

Temporarily set the No. 3 chain tensioner assembly only, do not install the bolt.



Hide 13053 5.INSTALL NO. 3 CAMSHAFT SUB-ASSEMBLY

HINT:

Perform Inspection After Repair after replacing the No. 3 camshaft sub-assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Clean the camshaft housing sub-assembly LH and No. 3 camshaft sub-assembly journals and apply engine oil to them.


b.
A366132C01
2.125,0.656 2.667,0.656 true 1.021,1.844 1.219,1.844 1.219,1.844 2.021,0.719 true 0.448,1.146 0.99,1.146 true 1.01,0.25 1.552,0.25 true 0.833,0.177 1.146,0.333 0.313,0.156 10 false *1 0.26,1.063 0.573,1.219 0.313,0.156 10 false *2 0.833,1.771 1.146,1.927 0.313,0.156 10 false *3 2.74,0.573 3.052,0.729 0.313,0.156 10 false *4
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem
*4 Valve Stem Cap


Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.


c.
A377812C01
1.021,3.396 0.677,2.833 0.677,2.833 0.49,2.833 true 2.031,3.563 2.052,2.917 2.052,2.917 2.24,2.917 true 0.292,2.771 0.604,2.927 0.313,0.156 10 false *a 2.292,2.854 2.604,3.01 0.313,0.156 10 false *b
*a Pin Hole
*b Straight Pin


Align the straight pin of the No. 3 camshaft sub-assembly and the pin hole of the camshaft timing gear assembly, and install the No. 3 camshaft sub-assembly to the camshaft timing gear assembly.

NOTICE:

Be careful not to damage the contact surface of the camshaft timing gear assembly with the straight pin of the No. 3 camshaft sub-assembly.



d.

Check that there is no clearance between the camshaft timing gear assembly and No. 3 camshaft sub-assembly flange.


Hide 13054 6.INSTALL NO. 4 CAMSHAFT SUB-ASSEMBLY

HINT:

Perform Inspection After Repair after replacing the No. 4 camshaft sub-assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Clean the camshaft housing sub-assembly LH and No. 4 camshaft sub-assembly journals and apply engine oil to them.


b.
A366132C01
2.125,0.656 2.667,0.656 true 1.021,1.844 1.219,1.844 1.219,1.844 2.021,0.719 true 0.448,1.146 0.99,1.146 true 1.01,0.25 1.552,0.25 true 0.833,0.177 1.146,0.333 0.313,0.156 10 false *1 0.26,1.063 0.573,1.219 0.313,0.156 10 false *2 0.833,1.771 1.146,1.927 0.313,0.156 10 false *3 2.74,0.573 3.052,0.729 0.313,0.156 10 false *4
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem
*4 Valve Stem Cap


Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.


c.
A377813C01
1.271,3.292 1.583,2.688 1.583,2.688 1.792,2.688 true 2.01,3.51 2.323,2.906 2.323,2.906 2.531,2.906 true 1.844,2.604 2.156,2.76 0.313,0.156 10 false *a 2.583,2.833 2.896,2.99 0.313,0.156 10 false *b
*a Pin Hole
*b Straight Pin


Align the straight pin of the No. 4 camshaft sub-assembly and the pin hole of the camshaft timing exhaust gear assembly, and install the No. 4 camshaft sub-assembly to the camshaft timing exhaust gear assembly.

NOTICE:

Be careful not to damage the contact surface of the camshaft timing exhaust gear assembly with the straight pin of the No. 4 camshaft sub-assembly.



d.

Check that there is no clearance between the camshaft timing exhaust gear assembly and No. 4 camshaft sub-assembly flange.


Hide 7.SET CAMSHAFT BEARING CAP (for Bank 2)

a.

Clean the camshaft bearing caps and apply engine oil to them.


b.
A380148

Slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly as shown in the illustration.

HINT:

To ensure there is sufficient space for installing the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap, slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly.



c.
A377814C01
2.906,1.604 3.135,1.604 false 2.771,2.01 3.052,2.01 3.052,2.01 3.052,1.604 false 2.833,1.844 3.052,1.844 false 1.885,0.594 1.99,0.198 1.99,0.198 2.177,0.198 false 2.292,1.052 2.49,0.375 2.49,0.375 2.677,0.375 false 3.177,1.531 3.396,1.729 0.219,0.198 10 false *a 2.219,0.135 2.531,0.292 0.313,0.156 10 false *b 2.719,0.302 3.031,0.458 0.313,0.156 10 false *c
*a Replacement Bolt and Washer
*b No. 3 Camshaft Bearing Cap
*c No. 4 Camshaft Bearing Cap


Remove the replacement bolts and washers (No. 3 camshaft bearing cap and No. 4 camshaft bearing cap side).

NOTICE:

Do not remove any of the replacement bolts and washers other than those on the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap side.



d.

Temporarily set the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.

NOTICE:
·

Do not install the bolts of the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.

·

Do not install any camshaft bearing caps other than the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.




e.
A377815

Slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly as shown in the illustration.

NOTICE:

Securely insert the straight pins of the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly into the pin holes of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.



Hide 8.TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 2)

a.

Check that there is no clearance between the camshaft timing gear assembly and No. 3 camshaft sub-assembly flange.


b.
A352538

Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration.


c.
A377816C01
1.948,0.24 2.26,0.396 0.313,0.156 10 false *a
*a Hold
V100135

Turn


Use a wrench to hold the hexagonal portion of the No. 3 camshaft sub-assembly.


d.

Temporarily install the camshaft timing gear bolt to the camshaft timing gear assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

Installing the camshaft timing gear bolt while there is external force applied to the camshaft timing gear assembly could result in damage to the engine, so make sure that the camshaft bearing cap is not installed when temporarily installing the camshaft timing gear bolt.

·

Be careful not to damage the No. 3 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with the wrench.

·

Make sure that the flange part of the camshaft timing gear bolt is directly contacting the camshaft timing gear assembly.




Hide 9.TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 2)

a.

Check that there is no clearance between the camshaft timing exhaust gear assembly and No. 4 camshaft sub-assembly flange.


b.
A352541

Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration.


c.
A377817C01
2.417,0.531 2.729,0.688 0.313,0.156 10 false *a
*a Hold
V100135

Turn


Use a wrench to hold the hexagonal portion of the No. 4 camshaft sub-assembly.


d.

Temporarily install the camshaft timing gear bolt to the camshaft timing exhaust gear assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

Installing the camshaft timing gear bolt while there is external force applied to the camshaft timing exhaust gear assembly could result in damage to the engine, so make sure that the camshaft bearing cap is not installed when temporarily installing the camshaft timing gear bolt.

·

Be careful not to damage the No. 4 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with the wrench.

·

Make sure that the flange part of the camshaft timing gear bolt is directly contacting the camshaft timing exhaust gear assembly.




Hide 10.INSTALL CAMSHAFT BEARING CAP (for Bank 2)

a.

Clean the camshaft bearing caps and apply engine oil to them.


b.
A377818C01
3.031,1.646 3.167,1.646 3.167,1.646 3.167,2.198 true 2.938,1.854 3.167,1.854 false 2.885,2.021 3.167,2.021 false 3.104,2.208 3.365,2.406 0.26,0.198 10 false *a 1.969,2.479 2.281,2.635 0.313,0.156 10 false *b 2.646,2.469 2.958,2.625 0.313,0.156 10 false *c
*a Replacement Bolt and Washer
*b Replacement Bolt and Washer Removal
*c Part Installation
V100135

Bolt (A)
V100136

Bolt (B)


Check the marks and numbers on the camshaft bearing caps, and then remove the replacement bolts and washers in the order shown in the illustration. Immediately after removing the replacement bolts and washers in the location for a camshaft bearing cap, install the camshaft bearing cap with the bolts in the order shown in the illustration.

Torque:
Bolt (A) : 28 N*m (286 kgf*cm, 21 ft.*lbf)
Bolt (B) : 16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:
·

Be sure to follow the numerical order when performing this procedure.

·

Do not drop replacement bolts and washers into the cylinder head LH.




c.

Check the torque of each bolt again.


Hide 11.TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 2)

a.
A377819C01
2.146,0.271 2.458,0.427 0.313,0.156 10 false *a
*a Hold
V100135

Turn


Use a wrench to hold the hexagonal portion of the No. 3 camshaft sub-assembly.


b.

Tighten the camshaft timing gear bolt.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Be careful not to damage the No. 3 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with the wrench.



Hide 12.TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 2)

a.
A377820C05
2.542,0.49 2.854,0.646 0.313,0.156 10 false *a
*a Hold
V100135

Turn


Use a wrench to hold the hexagonal portion of the No. 4 camshaft sub-assembly.


b.

Tighten the camshaft timing gear bolt.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Be careful not to damage the No. 4 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with the wrench.



Hide 13560A 13.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

a.

Install the No. 3 chain tensioner assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13506 14.CONNECT CHAIN SUB-ASSEMBLY (for Bank 2)

a.
A377821C01
1.646,3.365 1.24,3.365 true 1.677,3.302 1.99,3.5 0.313,0.198 10 true *a
*a Paint Mark


Align the paint marks on the camshaft timing gear assembly and chain sub-assembly and install the chain sub-assembly to the camshaft timing gear assembly.

HINT:

If the paint marks are not aligned, align them by turning the No. 3 camshaft sub-assembly slightly.



Hide 13050 15.SET CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 1)

HINT:

Perform Inspection After Repair after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A377822C01
0.75,0.656 1.281,0.208 1.281,0.208 1.458,0.208 true 0.792,1.5 0.792,0.792 true 0.74,1.5 1.052,1.656 0.313,0.156 10 false *a 1.51,0.135 1.823,0.292 0.313,0.156 10 false *b
*a Timing Mark
*b Mark Plate


Align the mark plate (yellow) with the timing mark of the camshaft timing gear assembly as shown in the illustration and install the No. 2 chain sub-assembly to the camshaft timing gear assembly.


b.
A377823C01
1.427,0.635 1.708,0.635 1.708,0.635 2.208,1.156 true 1.177,0.563 1.417,0.781 0.24,0.219 10 true *a
*a Place on camshaft timing gear assembly


Install the chain sub-assembly to the camshaft timing gear assembly, and then set the camshaft timing gear assembly to the camshaft housing sub-assembly.

HINT:
·

Place the chain sub-assembly on the camshaft timing gear assembly but do not engage the teeth of the sprocket and the chain sub-assembly.

·

Be sure to install the camshaft timing gear assembly with the timing mark facing upward.




Hide 13070A 16.SET CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 1)

HINT:

Perform Inspection After Repair after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A377824C01
1.51,2.823 1.302,2.823 1.302,2.823 0.708,2.417 true 0.281,1.542 0.448,1.542 0.448,1.542 0.688,2.052 true 0.094,1.469 0.406,1.625 0.313,0.156 10 false *a 1.542,2.75 1.854,2.906 0.313,0.156 10 true *b
*a Timing Mark
*b Mark Plate


Align the mark plate (yellow) with the timing mark of the camshaft timing exhaust gear assembly as shown in the illustration and install the No. 2 chain sub-assembly to the camshaft timing exhaust gear assembly.


b.

Set the camshaft timing exhaust gear assembly to the camshaft housing sub-assembly.


Hide 13550 17.SET NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A377791

While lifting up the camshaft timing exhaust gear assembly, pass the No. 2 chain tensioner assembly through the No. 2 chain sub-assembly and set it in place.

NOTICE:

Temporarily set the No. 2 chain tensioner assembly only, do not install the bolt.



Hide 13511 18.INSTALL CAMSHAFT

HINT:

Perform Inspection After Repair after replacing the camshaft.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A380149C01
1.198,2.094 1.458,2.094 1.458,2.094 1.594,2 true 0.958,1.979 1.188,2.177 0.229,0.198 10 true *a
*a 5 to 10°


Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain sub-assembly can be installed easily.

HINT:

When turning the crankshaft, engine oil may spray out of the oil holes.



b.

Clean the camshaft housing sub-assembly and camshaft journals and apply engine oil to them.


c.
A366132C01
2.125,0.656 2.667,0.656 true 1.021,1.844 1.219,1.844 1.219,1.844 2.021,0.719 true 0.448,1.146 0.99,1.146 true 1.01,0.25 1.552,0.25 true 0.833,0.177 1.146,0.333 0.313,0.156 10 false *1 0.26,1.063 0.573,1.219 0.313,0.156 10 false *2 0.833,1.771 1.146,1.927 0.313,0.156 10 false *3 2.74,0.573 3.052,0.729 0.313,0.156 10 false *4
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem
*4 Valve Stem Cap


Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.


d.
A377825C01
1.042,3.396 0.76,2.75 0.76,2.75 0.573,2.75 true 2.021,3.604 2.115,2.948 2.115,2.948 2.333,2.948 true 0.396,2.677 0.708,2.833 0.313,0.156 10 false *a 2.375,2.875 2.688,3.031 0.313,0.156 10 false *b
*a Pin Hole
*b Straight Pin


Align the straight pin of the camshaft and the pin hole of the camshaft timing gear assembly, and install the camshaft to the camshaft timing gear assembly.

NOTICE:

Be careful not to damage the contact surface of the camshaft timing gear assembly with the straight pin of the camshaft.



e.

Check that there is no clearance between the camshaft timing gear assembly and camshaft flange.


Hide 13512 19.INSTALL NO. 2 CAMSHAFT

HINT:

Perform Inspection After Repair after replacing the No. 2 camshaft.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Clean the camshaft housing sub-assembly and No. 2 camshaft journals and apply engine oil to them.


b.
A366132C01
2.125,0.656 2.667,0.656 true 1.021,1.844 1.219,1.844 1.219,1.844 2.021,0.719 true 0.448,1.146 0.99,1.146 true 1.01,0.25 1.552,0.25 true 0.833,0.177 1.146,0.333 0.313,0.156 10 false *1 0.26,1.063 0.573,1.219 0.313,0.156 10 false *2 0.833,1.771 1.146,1.927 0.313,0.156 10 false *3 2.74,0.573 3.052,0.729 0.313,0.156 10 false *4
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem
*4 Valve Stem Cap


Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.


c.
A377826C01
1.365,3.333 1.885,2.573 1.885,2.573 2.115,2.573 true 2,3.531 2.375,2.948 2.375,2.948 2.604,2.948 true 2.167,2.5 2.479,2.656 0.313,0.156 10 false *a 2.656,2.875 2.969,3.031 0.313,0.156 10 false *b
*a Pin Hole
*b Straight Pin


Align the straight pin of the No. 2 camshaft and the pin hole of the camshaft timing exhaust gear assembly, and install the No. 2 camshaft to the camshaft timing exhaust gear assembly.

NOTICE:

Be careful not to damage the contact surface of the camshaft timing exhaust gear assembly with the straight pin of the No. 2 camshaft.



d.

Check that there is no clearance between the camshaft timing gear assembly and No. 2 camshaft flange.


Hide 20.SET CAMSHAFT BEARING CAP (for Bank 1)

a.

Clean the camshaft bearing caps and apply engine oil to them.


b.
A380150

Slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly as shown in the illustration.

HINT:

To ensure there is sufficient space for installing the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap, slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly.



c.
A377827C01
0.385,1.417 0.708,1.417 false 0.51,1.417 0.51,1.802 0.51,1.802 0.844,1.802 false 0.51,1.625 0.781,1.625 false 1.01,0.625 1.302,0.625 1.302,0.625 1.542,0.854 true 1.479,0.229 1.771,0.229 1.771,0.229 2.01,0.458 true 0.208,1.344 0.521,1.5 0.313,0.156 10 false *a 1.302,0.167 1.615,0.323 0.313,0.156 10 false *b 0.781,0.552 0.99,0.76 0.208,0.208 10 true *c
*a Replacement Bolt and Washer
*b No. 1 Camshaft Bearing Cap
*c No. 2 Camshaft Bearing Cap


Remove the replacement bolts and washers (No. 1 camshaft bearing cap and No. 2 camshaft bearing cap side).

NOTICE:

Do not remove any of the replacement bolts and washers other than those on the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap side.



d.

Temporarily set the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.

NOTICE:
·

Do not install the bolts of the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.

·

Do not install any camshaft bearing caps other than the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.




e.
A377828

Slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly as shown in the illustration.

NOTICE:

Securely insert the straight pins of the camshaft and No. 2 camshaft into the pin holes of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.



Hide 21.TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 1)

a.

Check that there is no clearance between the camshaft timing gear assembly and camshaft flange.


b.
A352538

Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration.


c.
A377829C01
1.073,0.115 1.385,0.271 0.313,0.156 10 false *a
*a Hold
V100135

Turn


Use a wrench to hold the hexagonal portion of the camshaft.


d.

Temporarily install the camshaft timing gear bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

Installing the camshaft timing gear bolt while there is external force applied to the camshaft timing gear assembly could result in damage to the engine, so make sure that the camshaft bearing cap is not installed when temporarily installing the camshaft timing gear bolt.

·

Be careful not to damage the camshaft, camshaft housing sub-assembly or spark plug tube with the wrench.

·

Make sure that the flange part of the camshaft timing gear bolt is directly contacting the camshaft timing gear assembly.




Hide 22.TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 1)

a.

Check that there is no clearance between the camshaft timing exhaust gear assembly and No. 2 camshaft flange.


b.
A352541

Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration.


c.
A377830C01
0.792,0.458 1.104,0.615 0.313,0.156 10 false *a
*a Hold
V100135

Turn


Use a wrench to hold the hexagonal portion of the No. 2 camshaft.


d.

Temporarily install the camshaft timing gear bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

Installing the camshaft timing gear bolt while there is external force applied to the camshaft timing exhaust gear assembly could result in damage to the engine, so make sure that the camshaft bearing cap is not installed when temporarily installing the camshaft timing gear bolt.

·

Be careful not to damage the No. 2 camshaft, camshaft housing sub-assembly or spark plug tube with the wrench.

·

Make sure that the flange part of the camshaft timing gear bolt is directly contacting the camshaft timing exhaust gear assembly.




Hide 23.INSTALL CAMSHAFT BEARING CAP (for Bank 1)

a.

Clean the camshaft bearing caps and apply engine oil to them.


b.
A377831C01
0.208,2.135 0.208,1.563 0.208,1.563 0.385,1.563 false 0.208,1.781 0.458,1.781 false 0.208,1.948 0.521,1.948 false 0.146,2.146 0.458,2.302 0.313,0.156 10 false *a 1.969,2.479 2.281,2.635 0.313,0.156 10 false *b 2.646,2.469 2.958,2.625 0.313,0.156 10 false *c
*a Replacement Bolt and Washer
*b Replacement Bolt and Washer Removal
*c Part Installation
V100135

Bolt (A)
V100136

Bolt (B)
V100137

Bolt (C)


Check the marks and numbers on the camshaft bearing caps, and then remove the replacement bolts and washers in the order shown in the illustration. Immediately after removing the replacement bolts and washers in the location for a camshaft bearing cap, install the camshaft bearing cap with the bolts in the order shown in the illustration.

Torque:
Bolt (A) : 28 N*m (286 kgf*cm, 21 ft.*lbf)
Bolt (B), (C) : 16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:
·

Be sure to follow the numerical order when performing this procedure.

·

Do not drop replacement bolts and washers into the cylinder head sub-assembly.




c.

Check the torque of each bolt again.


Hide 24.TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 1)

a.
A377832C04
1.042,0.177 1.354,0.333 0.313,0.156 10 false *a
*a Hold
V100135

Turn


Use a wrench to hold the hexagonal portion of the camshaft.


b.

Tighten the camshaft timing gear bolt.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Be careful not to damage the camshaft, camshaft housing sub-assembly or spark plug tube with the wrench.



Hide 25.TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 1)

a.
A377833C01
0.729,0.427 1.042,0.583 0.313,0.156 10 false *a
*a Hold
V100135

Turn


Use a wrench to hold the hexagonal portion of the No. 2 camshaft.


b.

Tighten the camshaft timing gear bolt.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Be careful not to damage the No. 2 camshaft, camshaft housing sub-assembly or spark plug tube with the wrench.



Hide 13550 26.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

a.

Install the No. 2 chain tensioner assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13506 27.CONNECT CHAIN SUB-ASSEMBLY (for Bank 1)

a.
A377834C01
1.802,3.417 2.219,3.417 true 1.583,3.354 1.792,3.542 0.208,0.188 10 true *a
*a Paint Mark


Align the paint marks on the camshaft timing gear assembly and chain sub-assembly and install the chain sub-assembly to the camshaft timing gear assembly.

HINT:

If the paint marks are not aligned, align them by turning the camshaft slightly.



Hide 13540 28.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A380151N01
3.052,0.844 3.25,1.083 0.198,0.24 10 true 0° 2.688,0.177 3,0.375 0.313,0.198 10 true 30°

Turn the crankshaft counterclockwise 30° past the "0" timing mark, and then turn it clockwise to align the notch with the "0" timing mark.


b.

Turn the crankshaft slightly to eliminate the slack in the chain sub-assembly.

HINT:

Make sure there is some slack in the chain sub-assembly around the area where the No. 1 chain tensioner assembly is installed.



c.
A409059C01
0.448,1.604 0.865,1.188 true 2.833,1.125 3.042,0.594 true 1.635,1.969 1.635,1.76 false 3.042,1.656 3.042,1.448 true 0.281,1.521 0.594,1.719 0.313,0.198 10 false *a 3.073,0.479 3.385,0.677 0.313,0.198 10 false *a 2.99,1.677 3.302,1.875 0.313,0.198 10 false *b 1.573,1.99 1.885,2.167 0.313,0.177 10 false *b
*a Stopper Plate
*b Plunger


Turn the stopper plate clockwise to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.


d.

Turn the stopper plate counterclockwise to set the lock, and insert a 1.0 mm (0.0394 in.) diameter pin into the hole of the stopper plate.


e.

Install the No. 1 chain tensioner assembly to the cylinder head sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.

Remove the 1.0 mm (0.0394 in.) diameter pin from the No. 1 chain tensioner assembly.


Hide 29.INSPECT VALVE TIMING

a.

Check the camshaft timing marks.

NOTICE:
·

Check each timing mark from a viewpoint directly in line with the center of the camshaft and the timing mark on each camshaft timing gear assembly and each camshaft timing exhaust gear assembly.

·

If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.




b.

Check that each camshaft timing mark is positioned as shown in the illustration.

A377835C01
1.135,0.719 0.729,0.365 0.729,0.365 1.135,0.5 true 5.969,2.115 6.406,1.875 6.406,1.875 5.927,1.906 true 4.385,0.875 4.813,0.323 4.813,0.323 4.375,0.458 true 2.771,2.396 2.302,1.76 2.302,1.76 2.75,1.885 true 5.906,2.094 6.375,1.885 true 4.323,0.875 4.792,0.333 true 0.521,0.281 0.74,0.469 0.219,0.188 10 true *a 0.781,3.49 1.094,3.646 0.313,0.156 10 false *b 1.458,3.094 1.771,3.25 0.313,0.156 10 false *b 4.302,3.229 4.615,3.385 0.313,0.156 10 false *b 5.031,3.573 5.344,3.729 0.313,0.156 10 false *b 6.479,1.813 6.698,2 0.219,0.188 10 true *a 4.844,0.229 5.063,0.417 0.219,0.188 10 true *a 2.073,1.667 2.292,1.854 0.219,0.188 10 true *a
*a Timing Mark *b Viewpoint


HINT:
A377836N01
1.344,0.021 1.51,0.177 0.167,0.156 10 true A 1.656,0.021 1.823,0.177 0.167,0.156 10 true B 1.948,0.021 2.115,0.177 0.167,0.156 10 true C 2.208,0.021 2.375,0.177 0.167,0.156 10 true D

For the camshaft or No. 3 camshaft sub-assembly:

Be sure to check mark (A) at the point where marks (B), (C) and (D) are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.



c.

If the valve timing is misaligned, reinstall the chain sub-assembly.


d.

Turn the crankshaft 2 revolutions, set the No. 1 cylinder to TDC/compression and check the timing marks again.


Hide 11324 30.INSTALL TIMING CHAIN COVER PLATE

Hide 11193 31.INSTALL SPARK PLUG TUBE GASKET

Hide 11202 32.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11201 33.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 15370 34.INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)

Hide 15370 35.INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)

Hide 15370 36.INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)

Hide 15370 37.INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)

Hide 16522 38.INSTALL WATER FILLER BRACKET

Hide 39.INSTALL WIRE HARNESS CLAMP BRACKET

Hide 11452 40.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 29300 41.INSTALL VACUUM PUMP ASSEMBLY

Hide 17176 43.INSTALL AIR SURGE TANK TO INTAKE MANIFOLD GASKET

Hide 17190 44.INSTALL INTAKE AIR SURGE TANK ASSEMBLY

Hide 25860 45.CONNECT PURGE VALVE (PURGE VSV)

Hide 22030 47.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 49.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND