Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › ENGINE UNIT › 2017.09–2017.12
RM33A0E _51 Engine / Hybrid System _065333 2GR-FKS ENGINE MECHANICAL _0327371 ENGINE UNIT A

2GR-FKS ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 16322 1.INSTALL WATER INLET PIPE

a.
A408666

Install the water inlet pipe with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11102 3.INSTALL CYLINDER HEAD LH

a.

Place the cylinder head LH onto the cylinder block sub-assembly.

NOTICE:
·

Do not allow oil to adhere to the bottom of the cylinder head LH.

·

Gently lower the cylinder head LH in order not to damage the No. 2 cylinder head gasket with the bottom of the cylinder head LH.



HINT:

The cylinder head set bolts are tightened in 3 progressive steps.



b.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.


c.

Step 1:

i.
A366099N02
0.719,0.083 0.875,0.281 0.156,0.198 10 true 8 1.417,0.083 1.573,0.281 0.156,0.198 10 true 1 2.125,0.083 2.281,0.281 0.156,0.198 10 true 3 2.844,0.073 3,0.271 0.156,0.198 10 true 5 0.698,1.74 0.854,1.938 0.156,0.198 10 true 6 1.417,1.729 1.573,1.927 0.156,0.198 10 true 4 2.146,1.729 2.302,1.927 0.156,0.198 10 true 2 2.865,1.75 3.021,1.948 0.156,0.198 10 true 7

Using a 10 mm bi-hexagon socket wrench, install and uniformly tighten the 8 cylinder head set bolts with 8 cylinder head set plate washers in several steps in the order shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)



d.

Step 2:

i.
A366131C01
1.292,1.531 1.708,1.115 false 1.344,0.396 1.656,0.552 0.313,0.156 10 false *a 1.156,1.51 1.469,1.667 0.313,0.156 10 false *b 2.698,0.354 3.01,0.51 0.313,0.156 10 false *a
*a Turn 90°
*b Paint Mark
V100135

Front of Engine


Mark each cylinder head set bolt head with paint as shown in the illustration.


ii.

Tighten the cylinder head set bolts 90° in the order shown in step 1.



e.

Step 3:

i.

Tighten the cylinder head set bolts an additional 90° in the order shown in step 1.


ii.

Check that the paint marks are now facing rearward.



f.
A366098N02
0.031,1.313 0.188,1.51 0.156,0.198 10 false 2 0.042,0.635 0.198,0.833 0.156,0.198 10 false 1

Tighten the 2 bolts in the order shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

HINT:

Perform Inspection After Repair after replacing the cylinder head LH.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 11101 5.INSTALL CYLINDER HEAD SUB-ASSEMBLY

a.

Place the cylinder head sub-assembly onto the cylinder block sub-assembly.

NOTICE:
·

Do not allow oil to adhere to the bottom of the cylinder head sub-assembly.

·

Gently lower the cylinder head sub-assembly in order not to damage the cylinder head gasket with the bottom of the cylinder head sub-assembly.



HINT:

The cylinder head set bolts are tightened in 3 progressive steps.



b.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.


c.

Step 1:

i.
A408667N02
1.167,0.208 1.323,0.406 0.156,0.198 10 true 1 1.885,1.844 2.042,2.042 0.156,0.198 10 true 2 1.885,0.219 2.042,0.417 0.156,0.198 10 true 3 1.188,1.844 1.344,2.042 0.156,0.198 10 true 4 2.573,0.24 2.729,0.438 0.156,0.198 10 true 5 0.49,1.844 0.646,2.042 0.156,0.198 10 true 6 2.594,1.854 2.75,2.052 0.156,0.198 10 true 7 0.469,0.208 0.625,0.406 0.156,0.198 10 true 8

Using a 10 mm bi-hexagon socket wrench, install and uniformly tighten the 8 cylinder head set bolts with 8 cylinder head set plate washers in several steps in the order shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)



d.

Step 2:

i.
A366131C01
1.292,1.531 1.708,1.115 false 1.344,0.396 1.656,0.552 0.313,0.156 10 false *a 1.156,1.51 1.469,1.667 0.313,0.156 10 false *b 2.698,0.354 3.01,0.51 0.313,0.156 10 false *a
*a Turn 90°
*b Paint Mark
V100135

Front of Engine


Mark each cylinder head set bolt head with paint as shown in the illustration.


ii.

Tighten the cylinder head set bolts 90° in the order shown in step 1.



e.

Step 3:

i.

Tighten the cylinder head set bolts an additional 90° in the order shown in step 1.


ii.

Check that the paint marks are now facing rearward.

HINT:

Perform Inspection After Repair after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Hide 11381A 6.INSTALL REAR ENGINE OIL SEAL

a.

Place the rear engine oil seal retainer on wooden blocks.


b.

Apply MP grease to the lip of a new rear engine oil seal.


c.
A366129C01
1.042,1.469 0.635,0.781 0.635,0.781 1.156,1 true 2.052,1.719 2.229,1.719 true 0.656,0.781 2.708,1.063 true 2.25,1.365 2.563,1.521 0.313,0.156 10 false *a 0.333,0.698 0.792,0.896 0.458,0.198 10 false SST 1.875,1.635 2.188,1.792 0.313,0.156 10 false *1
*1 Rear Engine Oil Seal Retainer
*a Oil Seal Protrusion Height


Using SST and a hammer, tap in the rear engine oil seal.

SST
09223-15030  
09950-70010  (09951-07100)

Oil Seal Protrusion Height:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap in the rear engine oil seal at an angle.




Hide 11381 7.INSTALL REAR ENGINE OIL SEAL RETAINER

a.
A366130C01
1.135,0.583 0.771,0.271 true 0.604,0.125 0.917,0.281 0.313,0.156 10 false *a
*a Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal Packing Diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the rear engine oil seal retainer within 3 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




b.
A366069N02
0.448,0.875 0.99,0.875 true 2.656,0.885 2.813,1.083 0.156,0.198 10 true A 0.406,0.292 0.563,0.49 0.156,0.198 10 true A 0.313,0.792 0.469,0.99 0.156,0.198 10 false B

Install the rear engine oil seal retainer to the cylinder block sub-assembly with the 6 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:
·

Be sure to apply adhesive to the bolts (A) before installing them.

·

Wipe off any seal packing that seeped out from the crankshaft position sensor insert part (B).




Hide 82219A 8.INSTALL SENSOR WIRE

a.
A408035

Install the sensor wire to the cylinder head LH and cylinder block sub-assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13716 9.INSTALL VALVE STEM CAP

a.
A408034

Install the 24 valve stem caps to the cylinder head sub-assembly and cylinder head LH.

NOTICE:
·

Install each part to its original position.

·

Do not drop the valve stem caps into the cylinder head sub-assembly.




Hide 13750 10.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

Inspect the valve lash adjuster assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION


b.
A408037

Install the 24 valve lash adjuster assemblies to the cylinder head sub-assembly and cylinder head LH.

NOTICE:

Install each part to its original position.



Hide 13801 11.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Apply engine oil to the valve lash adjuster assembly tip and valve stem cap end.


b.
A366132C01
2.125,0.656 2.667,0.656 true 1.021,1.844 1.219,1.844 1.219,1.844 2.021,0.719 true 0.448,1.146 0.99,1.146 true 1.01,0.25 1.552,0.25 true 0.833,0.177 1.146,0.333 0.313,0.156 10 false *1 0.26,1.063 0.573,1.219 0.313,0.156 10 false *2 0.833,1.771 1.146,1.927 0.313,0.156 10 false *3 2.74,0.573 3.052,0.729 0.313,0.156 10 false *4
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem
*4 Valve Stem Cap


Install the 24 No. 1 valve rocker arm sub-assemblies as shown in the illustration.

NOTICE:

Install each part to its original position.



Hide 11114A 12.INSTALL STRAIGHT PIN (for Bank 2)

HINT:

It is not necessary to remove the straight pin unless it is being replaced.


a.
A374013C01
2.448,2.313 2.76,2.469 0.313,0.156 10 false *a
*a Protrusion Height


Using a plastic hammer, tap in a new straight pin to the camshaft housing sub-assembly LH.

Standard Protrusion Height:

7.7 to 8.3 mm (0.303 to 0.327 in.)



Hide 11151A 13.INSTALL CAMSHAFT BEARING CAP SETTING RING PIN (for Bank 2)

HINT:

It is not necessary to remove the camshaft bearing cap setting ring pins unless they are being replaced.


a.
A374014C01
2.677,2.417 2.99,2.573 0.313,0.156 10 false *a
*a Protrusion Height


Using a plastic hammer, tap 10 new camshaft bearing cap setting ring pins into the camshaft housing sub-assembly LH.

Standard Protrusion Height:

2.7 to 3.3 mm (0.106 to 0.130 in.)



Hide 13053 14.INSTALL NO. 3 CAMSHAFT SUB-ASSEMBLY

a.

Apply a light coat of engine oil to the No. 3 camshaft sub-assembly journals and camshaft housing sub-assembly LH.


b.

Install the No. 3 camshaft sub-assembly to the camshaft housing sub-assembly LH.

HINT:

Perform Inspection After Repair after replacing the No. 3 camshaft sub-assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 13054 15.INSTALL NO. 4 CAMSHAFT SUB-ASSEMBLY

a.

Apply a light coat of engine oil to the No. 4 camshaft sub-assembly journals and camshaft housing sub-assembly LH.


b.

Install the No. 4 camshaft sub-assembly to the camshaft housing sub-assembly LH.

HINT:

Perform Inspection After Repair after replacing the No. 4 camshaft sub-assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 16.INSTALL CAMSHAFT BEARING CAP (for Bank 2)

a.
A366088

Install the 2 oil control valve filters to the 2 camshaft bearing caps.


b.

Apply engine oil to the 5 camshaft bearing caps.


c.
A371846

Install the 5 camshaft bearing caps to the camshaft housing sub-assembly LH.


d.
A366139N01
0.771,0.031 0.927,0.229 0.156,0.198 10 false 1 1.469,0.125 1.625,0.323 0.156,0.198 10 false 2 2.125,0.135 2.281,0.333 0.156,0.198 10 false 3 2.802,0.167 2.958,0.365 0.156,0.198 10 false 4 0.75,1.563 0.906,1.76 0.156,0.198 10 true 5 1.458,1.615 1.615,1.813 0.156,0.198 10 true 6 2.125,1.615 2.281,1.813 0.156,0.198 10 true 7 2.771,1.604 2.927,1.802 0.156,0.198 10 true 8

Temporarily install and tighten the 8 bolts in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13560A 17.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A409052C01
0.375,1.104 0.521,1.104 0.521,1.104 0.729,0.771 true 0.469,1.313 0.615,1.313 0.615,1.313 0.906,0.844 true 0.177,1 0.354,1.198 0.177,0.198 10 false *a 0.292,1.219 0.469,1.417 0.177,0.198 10 false *b
*a Pin
*b Plunger
V100136

Push


Install the No. 3 chain tensioner assembly to the camshaft housing sub-assembly LH with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

While pushing down the No. 3 chain tensioner assembly, insert a 1.0 mm (0.0394 in.) diameter pin into the hole to secure it.


Hide 13050 18.SET CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)

a.
A366146C01
2.76,0.875 1.719,1.219 1.719,1.219 2.833,0.917 true 0.792,0.594 1.698,1.219 1.698,1.219 0.875,0.583 true 0.802,0.969 1.667,1.604 1.667,1.604 3,0.917 true 1.625,1.271 1.938,1.427 0.313,0.156 10 false *a 1.604,1.646 1.917,1.802 0.313,0.156 10 false *b
*a Timing Mark
*b Mark Plate


Align the mark plates (yellow) with the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly as shown in the illustration.


b.

Align the straight pins of the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly with the pin holes of the camshaft timing gear assembly and camshaft timing exhaust gear assembly. Temporarily install the camshaft timing gear assembly and camshaft timing exhaust gear assembly with the No. 2 chain sub-assembly installed.

NOTICE:

Be careful not to damage the contact surface of the camshaft timing gear assembly and camshaft timing exhaust gear assembly with the straight pins of the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly.


HINT:

Perform Inspection After Repair after replacing the camshaft timing gear assembly or camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 19.TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 2)

Hide 20.TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 2)

Hide 11104A 21.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

a.
A366132C01
2.125,0.656 2.667,0.656 true 1.021,1.844 1.219,1.844 1.219,1.844 2.021,0.719 true 0.448,1.146 0.99,1.146 true 1.01,0.25 1.552,0.25 true 0.833,0.177 1.146,0.333 0.313,0.156 10 false *1 0.26,1.063 0.573,1.219 0.313,0.156 10 false *2 0.833,1.771 1.146,1.927 0.313,0.156 10 false *3 2.74,0.573 3.052,0.729 0.313,0.156 10 false *4
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem
*4 Valve Stem Cap


Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


b.
A381377C01
0.698,1.854 0.396,1.125 0.396,1.125 0.667,0.51 true 2.406,1.083 2.573,1.083 2.573,1.083 2.979,0.667 true 0.135,1.01 0.354,1.219 0.219,0.208 10 true *a 2.229,0.99 2.448,1.198 0.219,0.208 10 false *b 2.625,2.135 2.844,2.344 0.219,0.208 10 false *c 0.604,2.906 0.823,3.115 0.219,0.208 10 false *d
*a Continuous Line Area
*b Dashed Line Area
*c 3.0 to 4.0 mm
*d Separated by 4.0 to 6.0 mm (0.157 to 0.236 in.)


Apply seal packing as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal Packing Application Specification:
Area Seal Packing Diameter
Continuous Line Area 3.0 to 4.0 mm (0.118 to 0.157 in.)
Dashed Line Area 4.0 to 4.5 mm (0.157 to 0.177 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing sub-assembly LH within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.




c.

Install the camshaft housing sub-assembly LH and tighten the 15 bolts in the order shown in the illustration.

A381378C01
1.26,1.854 1.958,2.156 1.958,2.156 2.615,1.865 false 1.885,2.208 2.198,2.406 0.313,0.198 10 false *a 0.563,0.49 0.875,0.688 0.313,0.198 10 false *b 2.146,0.458 2.458,0.656 0.313,0.198 10 false *c 5.26,1.5 5.417,1.698 0.156,0.198 10 true 1 5.833,1.5 5.99,1.698 0.156,0.198 10 true 4 4,0.542 4.156,0.74 0.156,0.198 10 false 9 4.969,0.417 5.115,0.594 0.146,0.177 10 true 3 5.49,0.417 5.635,0.594 0.146,0.177 10 true 6 6.302,0.448 6.5,0.625 0.198,0.177 10 false 12 6.615,1.51 6.813,1.688 0.198,0.177 10 false 13 6.333,0.938 6.531,1.115 0.198,0.177 10 true 10 6.479,2.198 6.677,2.375 0.198,0.177 10 false 14 6.125,2.083 6.323,2.26 0.198,0.177 10 false 11 5.51,2.094 5.708,2.271 0.198,0.177 10 true 5 4.958,2.094 5.156,2.271 0.198,0.177 10 true 2 4.542,2.281 4.74,2.458 0.198,0.177 10 false 15 4,2 4.198,2.177 0.198,0.177 10 false 8 3.854,1.156 4.01,1.333 0.156,0.177 10 true 7
*a Straight Pin *b Intake Side
*c Exhaust Side - -
V100135

Bolt (A)
V100136

Bolt (B)


Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:
·

When installing the camshaft housing sub-assembly LH, correctly position the camshafts as shown in the illustration. Failure to do so may result in damage due to contact between the pistons and valves. If a camshaft is rotated, valve contact with a piston at TDC may occur.

·

Make sure that the No. 1 valve rocker arm sub-assemblies are correctly installed.

·

If it is necessary to loosen any of the bolts during installation, remove the camshaft housing sub-assembly LH, clean the installation surfaces, and reapply seal packing.

·

If it is necessary to remove the camshaft housing sub-assembly LH during installation, make sure that the previously applied seal packing does not enter any oil passages.



Bolt Length:
Item Length
Bolt (A) 68 mm (2.68 in.)
Bolt (B) 48 mm (1.89 in.)



d.
A381379N01
0.25,0.063 0.406,0.26 0.156,0.198 10 true 1 1.365,0.031 1.521,0.229 0.156,0.198 10 true 2 2.021,0.021 2.177,0.219 0.156,0.198 10 true 3 3.01,0.125 3.167,0.323 0.156,0.198 10 true 4 0.271,1.385 0.427,1.583 0.156,0.198 10 true 5 1.365,1.531 1.521,1.729 0.156,0.198 10 true 6 2.042,1.552 2.198,1.75 0.156,0.198 10 true 7 2.792,1.563 2.948,1.76 0.156,0.198 10 true 8

Tighten the 8 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


e.

Remove any protruding seal packing black.

NOTICE:

Be careful not to drop seal packing black into the cylinder head LH.



Hide 22.TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 2)

a.
A381380C01
1.656,0.25 1.969,0.448 0.313,0.198 10 false *a
*a Hold
V100135

Turn


Using a wrench to hold the hexagonal portion of the No. 3 camshaft sub-assembly, tighten the camshaft timing gear bolt of the camshaft timing gear assembly.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Be careful not to damage the No. 3 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with the wrench.



Hide 23.TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 2)

a.
A381381C01
1.896,0.542 2.208,0.74 0.313,0.198 10 false *a
*a Hold
V100135

Turn


Using a wrench to hold the hexagonal portion of the No. 4 camshaft sub-assembly, tighten the camshaft timing gear bolt of the camshaft timing exhaust gear assembly.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Be careful not to damage the No. 4 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with the wrench.



b.

Remove the pin from the No. 3 chain tensioner assembly.


Hide 11114A 24.INSTALL STRAIGHT PIN (for Bank 1)

HINT:

It is not necessary to remove the straight pin unless it is being replaced.


a.
A371801C01
2.344,2.292 2.656,2.448 0.313,0.156 10 false *a
*a Protrusion Height


Using a plastic hammer, tap in a new straight pin to the camshaft housing sub-assembly.

Standard Protrusion Height:

7.7 to 8.3 mm (0.303 to 0.327 in.)



Hide 11151A 25.INSTALL CAMSHAFT BEARING CAP SETTING RING PIN (for Bank 1)

HINT:

It is not necessary to remove the camshaft bearing cap setting ring pins unless they are being replaced.


a.
A371802C01
2.625,2.385 2.938,2.542 0.313,0.156 10 false *a
*a Protrusion Height


Using a plastic hammer, tap 10 new camshaft bearing cap setting ring pins into the camshaft housing sub-assembly.

Standard Protrusion Height:

2.7 to 3.3 mm (0.106 to 0.130 in.)



Hide 13511 26.INSTALL CAMSHAFT

a.

Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.


b.

Install the camshaft to the camshaft housing sub-assembly.

HINT:

Perform Inspection After Repair after replacing the camshaft.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 13512 27.INSTALL NO. 2 CAMSHAFT

a.

Apply a light coat of engine oil to the No. 2 camshaft journals and camshaft housing sub-assembly.


b.

Install the No. 2 camshaft to the camshaft housing sub-assembly.

HINT:

Perform Inspection After Repair after replacing the No. 2 camshaft.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 28.INSTALL CAMSHAFT BEARING CAP (for Bank 1)

a.
A366084

Install the 2 oil control valve filters to the 2 camshaft bearing caps.


b.

Apply engine oil to the 5 camshaft bearing caps.


c.
A371842

Install the 5 camshaft bearing caps to the camshaft housing sub-assembly.


d.
A371843

Install the fuel pump lifter housing to the camshaft housing sub-assembly.


e.
A371844C01
2.698,0.052 2.854,0.25 0.156,0.198 10 false 1 2.219,0.167 2.375,0.365 0.156,0.198 10 false 2 1.542,0.177 1.698,0.375 0.156,0.198 10 false 3 0.885,0.177 1.042,0.375 0.156,0.198 10 false 4 2.729,1.604 2.885,1.802 0.156,0.198 10 true 5 2.219,1.688 2.375,1.885 0.156,0.198 10 true 6 1.552,1.698 1.708,1.896 0.156,0.198 10 true 7 0.875,1.677 1.031,1.875 0.156,0.198 10 true 8 0.51,1.688 0.667,1.885 0.156,0.198 10 true 9
V100135

Bolt (A)
V100136

Bolt (B)


Temporarily install and tighten the 9 bolts in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Bolt Length:
Item Length
Bolt (A) 40 mm (1.57 in.)
Bolt (B) 58 mm (2.28 in.)



Hide 13550 29.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A409058C01
2.594,3.188 2.438,3.188 2.438,3.188 2.281,2.885 true 2.344,3.313 2.229,3.313 2.229,3.313 1.938,2.906 true 2.656,3.073 2.969,3.271 0.313,0.198 10 false *a 2.396,3.208 2.708,3.406 0.313,0.198 10 false *b
*a Pin
*b Plunger
V100136

Push


Install the No. 2 chain tensioner assembly to the camshaft housing sub-assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

While pushing up the No. 2 chain tensioner assembly, insert a 1.0 mm (0.0394 in.) diameter pin into the hole to secure it.


Hide 13050 30.SET CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)

a.
A366143C01
0.76,0.76 1.719,1.115 1.719,1.115 2.646,0.479 true 0.625,0.76 1.76,1.521 1.76,1.521 2.656,0.875 true 1.635,1.135 1.948,1.292 0.313,0.156 10 false *a 1.698,1.573 2.01,1.729 0.313,0.156 10 false *b
*a Timing Mark
*b Mark Plate


Align the mark plates (yellow) with the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly as shown in the illustration.


b.

Align the straight pins of the camshaft and No. 2 camshaft with the pin holes of the camshaft timing gear assembly and camshaft timing exhaust gear assembly. Temporarily install the camshaft timing gear assembly and camshaft timing exhaust gear assembly with the No. 2 chain sub-assembly installed.

NOTICE:

Be careful not to damage the contact surface of the camshaft timing gear assembly and camshaft timing exhaust gear assembly with the straight pins of the camshaft and No. 2 camshaft.


HINT:

Perform Inspection After Repair after replacing the camshaft timing gear assembly or camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 31.TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 1)

Hide 32.TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 1)

Hide 33.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A366132C01
2.125,0.656 2.667,0.656 true 1.021,1.844 1.219,1.844 1.219,1.844 2.021,0.719 true 0.448,1.146 0.99,1.146 true 1.01,0.25 1.552,0.25 true 0.833,0.177 1.146,0.333 0.313,0.156 10 false *1 0.26,1.063 0.573,1.219 0.313,0.156 10 false *2 0.833,1.771 1.146,1.927 0.313,0.156 10 false *3 2.74,0.573 3.052,0.729 0.313,0.156 10 false *4
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem
*4 Valve Stem Cap


Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


b.
A381383C01
1.313,0.677 1.563,0.26 1.563,0.26 1.729,0.26 true 1.792,0.177 2.104,0.375 0.313,0.198 10 false *a 0.802,2.427 1.115,2.625 0.313,0.198 10 false *b 2.76,2.552 3.073,2.75 0.313,0.198 10 false *c
*a Seal Packing
*b 3.0 to 4.0 mm
*c Separated by 4.0 to 6.0 mm (0.157 to 0.236 in.)


Apply seal packing as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal Packing Diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.




c.

Install the camshaft housing sub-assembly and tighten the 15 bolts in the order shown in the illustration.

A381384C01
4.198,1.865 4.594,1.865 false 5.646,1.896 6.042,1.896 true 3.969,1.771 4.281,1.969 0.313,0.198 10 false *a 5.458,1.813 5.771,2.01 0.313,0.198 10 false *a 5.188,0.458 5.5,0.656 0.313,0.198 10 false *b 3.865,0.448 4.177,0.646 0.313,0.198 10 false *c 6.292,1.729 6.604,1.927 0.313,0.198 10 false *d 2.063,0.99 2.219,1.188 0.156,0.198 10 true 1 1.625,0.969 1.781,1.167 0.156,0.198 10 true 4 1.042,1 1.198,1.198 0.156,0.198 10 true 7 0.75,1.125 0.948,1.323 0.198,0.198 10 true 13 0.667,1.781 0.865,1.979 0.198,0.198 10 true 15 0.906,2.177 1.104,2.375 0.198,0.198 10 false 14 1.385,2.188 1.583,2.385 0.198,0.198 10 false 8 1.917,2.198 2.115,2.396 0.198,0.198 10 false 5 2.438,2.208 2.635,2.406 0.198,0.198 10 false 2 3.146,2.177 3.344,2.375 0.198,0.198 10 false 11 3.281,1.313 3.479,1.51 0.198,0.198 10 true 10 3.188,0.646 3.385,0.844 0.198,0.198 10 true 12 2.385,0.51 2.542,0.708 0.156,0.198 10 true 3 1.906,0.49 2.063,0.688 0.156,0.198 10 true 6 1.177,0.5 1.333,0.698 0.156,0.198 10 true 9
*a Straight Pin *b Intake Side
*c Exhaust Side *d 45°
V100135

Bolt (A)
V100136

Bolt (B)


Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:
·

When installing the camshaft housing sub-assembly, correctly position the camshafts as shown in the illustration. Failure to do so may result in damage due to contact between the pistons and valves. If a camshaft is rotated, valve contact with a piston at TDC may occur.

·

Make sure that the No. 1 valve rocker arm sub-assemblies are correctly installed.

·

If it is necessary to loosen any of the bolts during installation, remove the camshaft housing sub-assembly, clean the installation surfaces, and reapply seal packing.

·

If it is necessary to remove the camshaft housing sub-assembly during installation, make sure that the previously applied seal packing does not enter any oil passages.



Bolt Length:
Item Length
Bolt (A) 68 mm (2.68 in.)
Bolt (B) 48 mm (1.89 in.)



d.
A381385N01
2.958,0.188 3.115,0.385 0.156,0.198 10 true 1 1.979,0.271 2.135,0.469 0.156,0.198 10 true 2 1.344,0.271 1.5,0.469 0.156,0.198 10 true 3 0.688,0.292 0.844,0.49 0.156,0.198 10 true 4 3.063,1.531 3.219,1.729 0.156,0.198 10 true 5 2.229,1.771 2.385,1.969 0.156,0.198 10 true 6 1.615,1.781 1.771,1.979 0.156,0.198 10 true 7 0.948,1.771 1.104,1.969 0.156,0.198 10 true 8 0.427,1.771 0.583,1.969 0.156,0.198 10 true 9

Tighten the 9 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


e.

Remove any protruding seal packing black.

NOTICE:

Be careful not to drop seal packing black into the cylinder head sub-assembly.



Hide 34.TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 1)

a.
A381386C01
1.156,0.063 1.469,0.26 0.313,0.198 10 false *a
*a Hold
V100135

Turn


Using a wrench to hold the hexagonal portion of camshaft, tighten the camshaft timing gear bolt of the camshaft timing gear assembly.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Be careful not to damage the camshaft, camshaft housing sub-assembly or spark plug tube with the wrench.



Hide 35.TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 1)

a.
A381387C01
0.885,0.427 1.198,0.625 0.313,0.198 10 false *a
*a Hold
V100135

Turn


Using a wrench to hold the hexagonal portion of No. 2 camshaft, tighten the camshaft timing gear bolt of the camshaft timing exhaust gear assembly.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Be careful not to damage the No. 2 camshaft, camshaft housing sub-assembly or spark plug tube with the wrench.



b.

Remove the pin from the No. 2 chain tensioner assembly.


Hide 13521A 36.INSTALL CRANKSHAFT TIMING GEAR KEY

a.
A366082

Install the 2 crankshaft timing gear keys to the crankshaft.


Hide 13521 37.INSTALL CRANKSHAFT TIMING SPROCKET

a.
A366053

Install the crankshaft timing sprocket to the crankshaft.


Hide 13562 38.INSTALL NO. 2 CHAIN VIBRATION DAMPER

a.
A366153

Install the 2 No. 2 chain vibration dampers to the cylinder head LH and cylinder head sub-assembly.


Hide 13561 39.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.
A366081

Install the No. 1 chain vibration damper to the cylinder head LH and cylinder block sub-assembly with the 2 bolts.

Torque:
22.5 N*m (229 kgf*cm, 17 ft.*lbf)


Hide 13530 40.INSTALL IDLE SPROCKET ASSEMBLY

a.
A366148C01
0.719,1.104 1.25,0.333 true 1.271,0.177 1.583,0.333 0.313,0.156 10 false *a
*a Knock Pin
V100135

Light coat of engine oil


Apply a light coat of engine oil to the rotating surface of the No. 1 idle gear shaft.


b.

Temporarily install the No. 1 idle gear shaft and idle sprocket assembly with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear shaft with the pin hole of the cylinder block sub-assembly.

NOTICE:

Make sure to install the No. 1 idle gear shaft installation in the correct direction.


HINT:

Check that there is no foreign matter on the No. 1 idle gear shaft or No. 2 idle gear shaft.



c.

Using a 10 mm hexagon socket wrench, tighten the No. 2 idle gear shaft.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)

HINT:

After installing the idle sprocket assembly, check that the idle sprocket assembly turns smoothly.



Hide 13506 41.INSTALL CHAIN SUB-ASSEMBLY

a.
A366149C01
0.594,1.229 1.698,2.188 1.698,2.188 2.552,1.188 true 0.469,2.115 0.469,1.208 true 1.708,2.167 2.458,1.188 true 3.156,2.083 2.635,1.115 true 0.385,2.146 0.698,2.302 0.313,0.156 10 false *a 1.625,2.208 1.938,2.365 0.313,0.156 10 false *b 3.115,2.094 3.427,2.25 0.313,0.156 10 false *a
*a Mark Plate
*b Timing Mark


Align the mark plates and timing marks as shown in the illustration and install the chain sub-assembly.

HINT:

The camshaft mark plates are yellow.



b.
A366150

Temporarily place the chain sub-assembly on the crankshaft as shown in the illustration.


c.
A366151C02
0.177,2.479 3.24,4.51 3.063,2.031 1.5,3.604 0.635,3.531 0.635,3.531 1.552,3.417 true 2.104,3.865 1.531,4.115 1.531,4.115 1.49,3.698 true 2.292,3.771 2.688,3.76 2.688,3.76 2.396,3.573 true 2.74,3.688 3.052,3.844 0.313,0.156 10 false *a 0.24,2.531 0.552,2.688 0.313,0.156 10 false *b 0.448,3.448 0.76,3.604 0.313,0.156 10 false *c 1.448,4.146 1.76,4.302 0.313,0.156 10 false *d
*a Chain Plate
*b When the idle sprocket assembly is reused
*c Mark
*d Align
V100135

Turn


Turn the camshaft timing gear assembly on bank 1 counterclockwise to tighten the chain sub-assembly between the banks.

NOTICE:

When reusing the idle sprocket assembly, align the chain plate with the mark where the mark plate had been in order to tighten the chain sub-assembly between the banks.



d.
A366152C01
2.917,1.75 3.063,1.073 true 2.646,1.823 2.385,2.021 2.385,2.021 2.854,1.802 true 3.01,0.875 3.323,1.031 0.313,0.156 10 true *a 2.219,1.979 2.531,2.135 0.313,0.156 10 false *b
*a Mark Plate
*b Timing Mark


Align the mark plate and timing marks as shown in the illustration and install the chain sub-assembly around the crankshaft timing sprocket.

HINT:

The crankshaft mark plate is pink.



e.

Temporarily tighten the crankshaft pulley set bolt to the crankshaft.


f.
A372412C01
0.604,0.365 1.198,0.167 true 0.458,1.396 0.896,0.854 true 1.229,0.083 1.542,0.24 0.313,0.156 10 true *a 0.344,1.427 0.656,1.583 0.313,0.156 10 false *b
*a Center Line
*b Key Groove


Turn the crankshaft clockwise to set it to the center line of the block bore (for Bank 1) (TDC /compression).


Hide 13559 42.INSTALL CHAIN TENSIONER SLIPPER

a.
A373576

Install the chain tensioner slipper to the cylinder block sub-assembly.


Hide 13540 43.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A366154C01
0.438,1.625 0.854,1.208 true 2.802,1.083 3.115,0.573 true 3.052,1.792 3.052,1.438 true 1.646,1.938 1.646,1.781 true 0.271,1.604 0.583,1.76 0.313,0.156 10 false *a 2.979,1.833 3.292,1.99 0.313,0.156 10 false *b 3.083,0.396 3.396,0.552 0.313,0.156 10 false *a 1.573,1.99 1.885,2.146 0.313,0.156 10 false *b
*a Stopper Plate
*b Plunger


Turn the stopper plate clockwise to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.


b.

Turn the stopper plate counterclockwise to set the lock, and insert a 1.0 mm (0.0394 in.) diameter pin into the hole of the stopper plate.


c.
A366155

Install the No. 1 chain tensioner assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Remove the 1.0 mm (0.0394 in.) diameter pin from the No. 1 chain tensioner assembly.


Hide 44.INSPECT VALVE TIMING

a.

Check the camshaft timing marks.

NOTICE:
·

Check each timing mark from a viewpoint directly in line with the center of the camshaft and the timing mark on each camshaft timing gear assembly and each camshaft timing exhaust gear assembly.

·

If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.




b.

Check that each camshaft timing mark is positioned as shown in the illustration.

A366156C01
1.167,0.74 2.333,0.5 2.333,0.5 1.156,0.5 true 2.813,2.438 3.969,1.906 3.969,1.906 2.792,1.906 true 4.396,1.01 5.552,0.479 5.552,0.479 4.375,0.479 true 4.333,0.917 5.521,0.49 true 5.948,2.073 4.927,1.906 4.927,1.906 5.917,1.906 true 5.906,2.115 4.948,1.917 true 2.396,0.427 2.708,0.583 0.313,0.156 10 false *a 0.75,3.552 1.063,3.708 0.313,0.156 10 false *b 1.438,3.115 1.75,3.271 0.313,0.156 10 false *b 4.354,3.271 4.667,3.427 0.313,0.156 10 false *b 5.063,3.573 5.375,3.729 0.313,0.156 10 false *b 4.021,1.813 4.333,1.969 0.313,0.156 10 false *a 5.604,0.396 5.917,0.552 0.313,0.156 10 false *a 4.76,1.813 5.073,1.969 0.313,0.156 10 false *a
*a Timing Mark *b Viewpoint


HINT:
A377836N01
1.344,0.021 1.51,0.177 0.167,0.156 10 true A 1.656,0.021 1.823,0.177 0.167,0.156 10 true B 1.948,0.021 2.115,0.177 0.167,0.156 10 true C 2.208,0.021 2.375,0.177 0.167,0.156 10 true D

For the camshaft or No. 3 camshaft sub-assembly:

Be sure to check the mark (A) at the point where the marks (B), (C) and (D) are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.



c.

If the valve timing is misaligned, reinstall the chain sub-assembly.


d.

Remove the crankshaft pulley set bolt from the crankshaft.


Hide 16100 45.INSTALL ENGINE WATER PUMP ASSEMBLY

a.
A366158

Install a new water pump gasket and the engine water pump assembly with the 7 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 11310 46.INSTALL TIMING CHAIN COVER ASSEMBLY

Hide 11324 48.INSTALL TIMING CHAIN COVER PLATE

a.
A373575

Install a new timing chain cover gasket and the timing chain cover plate to the timing chain cover assembly with the 4 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 12121 49.INSTALL NO. 1 OIL PAN BAFFLE PLATE

a.
A366068N01
2.677,1.865 3.021,2.083 0.344,0.219 10 true A, 7 0.646,0.177 0.99,0.396 0.344,0.219 10 true A, 5 2.094,1.875 2.25,2.073 0.156,0.198 10 true 3 1.469,1.875 1.625,2.073 0.156,0.198 10 true 8 0.75,1.875 0.906,2.073 0.156,0.198 10 true 4 2.802,0.208 2.958,0.406 0.156,0.198 10 true 6 2.083,0.208 2.24,0.406 0.156,0.198 10 true 2 1.438,0.188 1.594,0.385 0.156,0.198 10 true 1

Install the No. 1 oil pan baffle plate to the crankshaft bearing cap set bolt.


b.

Temporarily tighten the 2 bolts (A).


c.

Fully tighten the 8 bolts order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15679 50.INSTALL OIL FILTER BRACKET CLIP

a.
A371785

Install the oil filter bracket clip to the oil pan sub-assembly.


Hide 12101 51.INSTALL OIL PAN SUB-ASSEMBLY

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using an E8 and E6 "TORX" socket wrench, install the 4 stud bolts to the oil pan sub-assembly and cylinder block sub-assembly.

A373520C01
0.479,0.104 0.792,0.26 0.313,0.156 10 false *a 0.51,2.125 0.823,2.281 0.313,0.156 10 false *b 5.073,0.708 5.385,0.865 0.313,0.156 10 false *c 5.104,1.219 5.417,1.375 0.313,0.156 10 false *d 6.073,0.927 6.385,1.083 0.313,0.156 10 false *e 5.125,2.969 5.438,3.125 0.313,0.156 10 false *f 5.125,3.406 5.438,3.563 0.313,0.156 10 false *g 6.052,3.177 6.365,3.333 0.313,0.156 10 false *h 4.635,0.104 4.792,0.302 0.156,0.198 10 false A 4.635,2.396 4.792,2.594 0.156,0.198 10 false B 1.854,3.031 2.01,3.229 0.156,0.198 10 false B 1.625,2.865 1.781,3.063 0.156,0.198 10 false B 2.385,0.135 2.542,0.333 0.156,0.198 10 true A 3.125,1.771 3.281,1.969 0.156,0.198 10 true A
*a Cylinder Block Sub-assembly Side *b Oil Pan Sub-assembly Side
*c 20 mm (0.787 in.) *d 13 mm (0.512 in.)
*e 35 mm (1.38 in.) *f 16 mm (0.630 in.)
*g 9 mm (0.354 in.) *h 27 mm (1.06 in.)


Torque:
Stud bolt (A) : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Stud bolt (B) : 4.0 N*m (41 kgf*cm, 35 in.*lbf)



Hide 89491 52.INSTALL ENGINE OIL LEVEL SENSOR

Hide 15104 53.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new oil strainer gasket.


b.
A409029C01
1.885,0.458 2.104,0.188 2.104,0.188 2.5,0.188 true 1.833,0.448 1.531,0.188 1.531,0.188 1.125,0.188 false 2.563,0.125 2.875,0.281 0.313,0.156 10 false *a 0.906,0.125 1.219,0.281 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusion of the oil strainer gasket with the cutout of the oil strainer sub-assembly, and install the oil strainer gasket to the oil strainer sub-assembly.


c.
A366066

Install the oil strainer sub-assembly to the timing chain cover assembly with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12102A 54.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A366162C01
1.302,2.656 1.615,2.813 0.313,0.156 10 false *a 2.615,2.844 2.927,3 0.313,0.156 10 false *b 1.313,3.021 1.625,3.177 0.313,0.156 10 false *a
*a 9 mm (0.354 in.)
*b 19 mm (0.748 in.)


Using an E6 "TORX" socket wrench, install the 2 stud bolts to the oil pan sub-assembly as shown in the illustration.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
A366163C01
1.104,0.563 1.656,0.563 true 0.917,0.469 1.229,0.625 0.313,0.156 10 false *a
*a Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal Packing Diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the No. 2 oil pan sub-assembly within 3 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




c.
A366064C01
2.208,0.438 2.583,0.635 0.375,0.198 10 true *a, 1 0,1.594 0.375,1.792 0.375,0.198 10 false *a, 2 1.885,1.979 2.042,2.177 0.156,0.198 10 true 3 0.813,0.458 0.969,0.656 0.156,0.198 10 true 4 2.24,1.344 2.396,1.542 0.156,0.198 10 true 5 0.99,0 1.146,0.198 0.156,0.198 10 true 6 0.594,1.979 0.75,2.177 0.156,0.198 10 false 7 0.292,0.729 0.448,0.927 0.156,0.198 10 false 8 2.25,0.75 2.406,0.948 0.156,0.198 10 true 9 0.083,1.135 0.396,1.333 0.313,0.198 10 false 10 2.042,0 2.354,0.198 0.313,0.198 10 true 11 0.698,0.229 1.01,0.427 0.313,0.198 10 true 12 1.229,1.99 1.479,2.177 0.25,0.188 10 true 13 0.427,0.521 0.74,0.719 0.313,0.198 10 true 14 2.24,1.073 2.552,1.271 0.313,0.198 10 true 15 0.344,1.823 0.656,2.021 0.313,0.198 10 false 16 2.073,1.76 2.385,1.958 0.313,0.198 10 true 17
*a Nut


Install the No. 2 oil pan sub-assembly with the 15 bolts and 2 nuts as shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 83530 55.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 15620 56.INSTALL OIL FILTER CAP ASSEMBLY

Hide 12101A 57.INSTALL OIL PAN DRAIN PLUG

a.
A366044

Install a new oil pan drain plug gasket and the oil pan drain plug to the No. 2 oil pan sub-assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 11193 58.INSTALL SPARK PLUG TUBE GASKET

a.
A373587

Install 6 new spark plug tube gaskets to the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.


Hide 11202 59.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A408027

Install 3 new No. 2 cylinder head cover gaskets to the cylinder head cover sub-assembly LH.

NOTICE:

Make sure that there is no oil or foreign matter inside the groove of the camshaft housing sub-assembly LH or on the contact surfaces of the cylinder head cover sub-assembly LH and timing chain cover assembly. Clean if necessary.



b.
A366060

Install a new camshaft bearing cap oil hole gasket LH to the camshaft bearing cap.


c.

Apply seal packing as shown in the illustration.

A366168C01
0.781,1.448 0.385,1.854 0.385,1.854 0.833,2.292 true 1.115,2.375 1.365,1.823 1.365,1.823 1.094,1.302 true 4.448,1.625 4.448,1.375 false 5.135,1.625 5.135,1.375 false 4.615,2.167 4.427,2.167 4.427,2.167 3.979,2.375 true 4.25,2.958 5.115,3.542 5.115,3.542 6.052,2.938 true 6.313,2.365 5.896,2.156 5.896,2.156 5.708,2.156 true 5.5,1.083 5.813,1.24 0.313,0.156 10 false *d 1.396,1.229 1.552,1.427 0.156,0.198 10 true A 0.219,1.771 0.531,1.927 0.313,0.156 10 false *b 4.729,0.094 4.885,0.292 0.156,0.198 10 false A 5.083,1.958 5.24,2.156 0.156,0.198 10 false B 0.969,1.552 1.125,1.75 0.156,0.198 10 true B 1.427,1.74 1.74,1.948 0.313,0.208 10 true *a 1.396,2.323 1.552,2.521 0.156,0.198 10 true A 1.052,1.927 1.208,2.125 0.156,0.198 10 true B 4.708,1.719 5.021,1.875 0.313,0.156 10 false *a 4.375,1.667 4.771,1.896 0.396,0.229 10 false *1 5.063,1.656 5.458,1.885 0.396,0.229 10 false *2 4.052,1.896 4.396,2.063 0.344,0.167 10 false *e 3.49,2.042 3.833,2.208 0.344,0.167 10 false *b 4.688,2.083 5,2.24 0.313,0.156 10 false *c 5.063,3.563 5.375,3.719 0.313,0.156 10 false *c 5.542,2.063 5.854,2.219 0.313,0.156 10 false *c 6.667,2.042 7.01,2.208 0.344,0.167 10 false *b 6.146,1.854 6.49,2.021 0.344,0.167 10 false *e
*1 Timing Chain Cover Assembly *2 Camshaft Housing Sub-assembly LH
*a Seal Packing (Diameter 2.0 to 3.0 mm (0.0787 to 0.118 in.)) *b Seal Packing (Diameter 5.0 to 7.0 mm (0.197 to 0.276 in.))
*c Mark *d 5.0 to 10 mm (0.197 to 0.394 in.)
*e Thickness: 1.0 to 3.0 mm (0.0394 to 0.118 in.) - -
V100135

Seal Packing - -


Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal Packing Application Specification:
Area Seal Packing Diameter
(A) Thickness: 5 to 10 mm (0.197 to 0.394 in.)
Width: 2 to 3 mm (0.0787 to 0.118 in.)
(B) Thickness: 1 to 3 mm (0.0394 to 0.118 in.)
Width: 5 to 7 mm (0.197 to 0.276 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the cylinder head cover sub-assembly LH within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




d.

Apply a light coat of engine oil to the 2 new O-rings of the 2 VVT sensors (for Exhaust Side of Bank 2 and for Intake Side of Bank 2).

NOTICE:

If reusing the 2 VVT sensors (for Exhaust Side of Bank 2 and for Intake Side of Bank 2), be sure to inspect them before installation.



e.

Clean the 2 bolts and 2 bolt holes of the VVT sensors (for Exhaust Side of Bank 2 and for Intake Side of Bank 2).


f.
A192239C77
1.573,0.76 1.677,0.76 1.677,0.76 1.823,1.24 false 1.375,0.677 1.573,0.833 0.198,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of the 2 bolts of the VVT sensors (for Exhaust Side of Bank 2 and for Intake Side of Bank 2).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



g.
A408678C01
1.156,0.75 1.833,0.938 1.833,0.938 1.771,1.344 true 1.885,0.854 2.125,1.021 0.24,0.167 10 true *a 0.865,1.281 1.271,1.458 0.406,0.177 10 true 1, 17 0.594,0.865 1,1.042 0.406,0.177 10 true 2, 18 1.99,1.958 2.167,2.135 0.177,0.177 10 true 3 1.396,0.042 1.573,0.219 0.177,0.177 10 true 4 2.135,0.031 2.313,0.208 0.177,0.177 10 true 5 1.333,1.969 1.51,2.146 0.177,0.177 10 true 6 2.729,1.917 2.906,2.094 0.177,0.177 10 true 7 0.646,0.031 0.823,0.208 0.177,0.177 10 true 8 3.031,0.042 3.208,0.219 0.177,0.177 10 true 9 0.688,2 0.896,2.177 0.208,0.177 10 true 10 3.115,1.938 3.323,2.104 0.208,0.167 10 true 11 0.198,0.052 0.406,0.219 0.208,0.167 10 true 12 3.188,0.208 3.396,0.375 0.208,0.167 10 true 13 0.198,1.927 0.406,2.094 0.208,0.167 10 true 14 3.188,1.344 3.396,1.51 0.208,0.167 10 true 15 0.042,1.385 0.25,1.552 0.208,0.167 10 true 16
*a Bolt with VVT Sensor


Install the cylinder head cover sub-assembly LH with the 16 bolts and 2 VVT sensors (for Exhaust Side of Bank 2 and for Intake Side of Bank 2) in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If a VVT sensor (for Exhaust Side of Bank 2 or for Intake Side of Bank 2) has been struck or dropped, replace it.

·

Make sure that the 2 O-rings are not cracked or moved out of place when installing the 2 VVT sensors (for Exhaust Side of Bank 2 and for Intake Side of Bank 2).



HINT:

After tightening all bolts, check the tightening torque of the bolts (1) and (18). Retighten them if necessary.



h.
A408104

Install the No. 1 V-bank cover bracket to the cylinder head cover sub-assembly LH.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11201 60.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A366062

Install 3 new cylinder head cover gaskets to the cylinder head cover sub-assembly.

NOTICE:

Make sure that there is no oil or foreign matter inside the groove of the camshaft housing sub-assembly or on the contact surfaces of the cylinder head cover sub-assembly and timing chain cover assembly. Clean if necessary.



b.
A366058

Install a new camshaft bearing cap oil hole gasket to the camshaft bearing cap.


c.

Apply seal packing as shown in the illustration.

A366166C01
0.823,1.594 1.094,1.26 1.094,1.26 0.927,0.896 true 2.813,1.833 2.552,1.281 2.552,1.281 2.833,0.74 true 3.083,1.719 3.438,1.302 3.438,1.302 3.146,0.896 true 2.917,3.969 2,4.563 2,4.563 1.021,3.99 true 5.177,2.104 5.177,1.813 false 5.865,2.115 5.865,1.823 false 6.208,3.375 5.76,3.375 false 4.688,3.354 4.24,3.354 false 3.135,3.365 2.625,3.021 2.625,3.021 2.438,3.021 true 1.594,3.031 1.344,3.031 1.344,3.031 0.802,3.375 true 2.333,1.167 2.521,1.427 0.188,0.26 10 true *a 5.448,2.167 5.646,2.396 0.198,0.229 10 false *a 1.125,1.188 1.438,1.344 0.313,0.156 10 true *b 4.698,1.521 5.031,1.792 0.333,0.271 10 false *d 4.865,2.677 5.021,2.875 0.156,0.198 10 false D 2.823,0.958 2.979,1.156 0.156,0.198 10 true A 5.5,0.531 5.656,0.729 0.156,0.198 10 false B 2.396,0.635 2.552,0.833 0.156,0.198 10 true B 3.49,1.24 3.688,1.469 0.198,0.229 10 false *b 5.104,2.146 5.292,2.406 0.188,0.26 10 false *2 1.219,0.802 1.375,1 0.156,0.198 10 true C 1.083,1.563 1.24,1.76 0.156,0.198 10 true D 2.802,1.469 2.958,1.667 0.156,0.198 10 true A 2.375,1.781 2.531,1.979 0.156,0.198 10 true B 5.802,2.146 5.99,2.406 0.188,0.26 10 false *1 1.917,4.594 2.135,4.813 0.219,0.219 10 false *c 6.385,2.677 6.542,2.875 0.156,0.198 10 false C 5.594,3.292 5.813,3.51 0.219,0.219 10 false *c 4.083,3.271 4.302,3.49 0.219,0.219 10 false *c 6.719,4.083 6.917,4.313 0.198,0.229 10 false *e 6.344,4.427 6.542,4.656 0.198,0.229 10 false *b 5.188,4.083 5.385,4.313 0.198,0.229 10 false *e 4.813,4.427 5.01,4.656 0.198,0.229 10 false *b 2.26,2.938 2.479,3.156 0.219,0.219 10 false *c 1.656,2.958 1.875,3.177 0.219,0.219 10 false *c 1.969,2.948 2.125,3.146 0.156,0.198 10 false A 0.854,2.906 1.052,3.135 0.198,0.229 10 false *e 0.302,3.094 0.5,3.323 0.198,0.229 10 false *b 3.458,3.063 3.656,3.292 0.198,0.229 10 false *b 2.958,2.865 3.156,3.094 0.198,0.229 10 false *e
*1 Timing Chain Cover Assembly *2 Camshaft Housing Sub-assembly
*a Seal Packing (Diameter 2.0 to 3.0 mm (0.0787 to 0.118 in.)) *b Seal Packing (Diameter 5.0 to 7.0 mm (0.197 to 0.276 in.))
*c Mark *d 5.0 to 10 mm (0.197 to 0.394 in.)
*e Thickness: 1.0 to 3.0 mm (0.0394 to 0.118 in.) - -
V100135

Seal Packing - -


Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




d.

Apply a light coat of engine oil to the 2 new O-rings of the 2 VVT sensors (for Exhaust Side of Bank 1 and for Intake Side of Bank 1).

NOTICE:

If reusing the 2 VVT sensors (for Exhaust Side of Bank 1 and for Intake Side of Bank 1), be sure to inspect them before installation.



e.

Clean the 2 bolts and 2 bolt holes of the VVT sensors (for Exhaust Side of Bank 1 and for Intake Side of Bank 1).


f.
A192239C77
1.573,0.76 1.677,0.76 1.677,0.76 1.823,1.24 false 1.375,0.677 1.573,0.833 0.198,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of the 2 bolts of the VVT sensors (for Exhaust Side of Bank 1 and for Intake Side of Bank 1).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



g.
A373589C03
1.302,1.385 1.01,1.094 1.01,1.094 1.302,0.802 true 0.74,1 0.979,1.25 0.24,0.25 10 true *a 1.688,0.802 2.125,1.052 0.438,0.25 10 true 1, 16 1.667,1.125 2.104,1.375 0.438,0.25 10 true 2, 17 0.156,0.052 0.469,0.25 0.313,0.198 10 false 13 0,0.542 0.313,0.74 0.313,0.198 10 true 15 3,1.979 3.313,2.177 0.313,0.198 10 false 10 0,1.896 0.313,2.094 0.313,0.198 10 false 11 3.198,1.427 3.427,1.635 0.229,0.208 10 false 14 0.958,1.979 1.115,2.177 0.156,0.198 10 false 7 1.823,1.979 1.979,2.177 0.156,0.198 10 true 3 2.583,1.979 2.74,2.177 0.156,0.198 10 true 6 3.198,0.031 3.427,0.24 0.229,0.208 10 false 12 2.813,0 2.969,0.198 0.156,0.198 10 true 8 2.167,0 2.323,0.198 0.156,0.198 10 true 4 1.198,0.052 1.354,0.25 0.156,0.198 10 true 5 0.51,0 0.667,0.198 0.156,0.198 10 true 9
*a Bolt with VVT Sensor


Install the cylinder head cover sub-assembly with the 15 bolts and 2 VVT sensors (for Exhaust Side of Bank 1 and for Intake Side of Bank 1) in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If a VVT sensor (for Exhaust Side of Bank 1 or for Intake Side of Bank 1) has been struck or dropped, replace it.

·

Make sure that the 2 O-rings are not cracked or moved out of place when installing the 2 VVT sensors (for Exhaust Side of Bank 1 and for Intake Side of Bank 1).



HINT:

After tightening all bolts, check the tightening torque of the bolts (1) and (17). Retighten them if necessary.



h.
A366056

Install the No. 1 engine cover sub-assembly to the cylinder head cover sub-assembly with the 2 clips.


Hide 16331 61.INSTALL WATER OUTLET

a.
A408665

Install 2 new No. 2 water inlet housing gaskets to the water outlet.


b.
A408664C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Install the water outlet to the cylinder head sub-assembly and cylinder head LH with the 4 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 89422 62.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

Hide 19312 64.INSTALL CRANKSHAFT POSITION SENSOR PROTECTOR

Hide 15370 65.INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)

Hide 15370 66.INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)

Hide 15370 67.INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)

Hide 15370 68.INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)

Hide 16031 69.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 16261 70.INSTALL WATER BY-PASS HOSE

a.
A415432

Install the water by-pass hose to the water inlet pipe and water inlet with thermostat sub-assembly and slide the 2 clips to secure it.


Hide 12315 71.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A408674C01
1.688,2.469 2,2.625 0.313,0.156 10 false *a 1.698,2.99 2.01,3.146 0.313,0.156 10 false *b 2.125,2.74 2.438,2.896 0.313,0.156 10 false *c
*a 14 mm (0.551 in.)
*b 13 mm (0.512 in.)
*c 29 mm (1.14 in.)


Using an E8 "TORX" socket wrench, install the 2 stud bolts to the front No. 1 engine mounting bracket LH.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
A408033N01
2.156,0.469 2.51,0.677 0.354,0.208 10 true C (1) 2.938,1.708 3.292,1.917 0.354,0.208 10 true C (2) 0.333,1.667 0.688,1.875 0.354,0.208 10 true C (7) 2.281,1.781 2.635,1.99 0.354,0.208 10 true A (6) 1.927,1.698 2.281,1.906 0.354,0.208 10 true A (5) 1.583,1.969 1.938,2.177 0.354,0.208 10 true A (4) 0.854,1.958 1.208,2.167 0.354,0.208 10 true B (3)

Install the front No. 1 engine mounting bracket LH to the timing chain cover assembly with the 7 bolts in the order shown in the illustration.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)

NOTICE:

Make sure that there is no oil on the threads of the bolts.


Bolt Length:
Item Length
Bolt (A) 115 mm (4.53 in.)
Bolt (B) 85 mm (3.35 in.)
Bolt (C) 40 mm (1.57 in.)



Hide 11415 73.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.
A366171C01
1.365,0.344 1.938,0.75 false 1.188,0.219 1.5,0.375 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to the cylinder block water drain cock sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Install the cylinder block water drain cock sub-assembly within 3 minutes of applying adhesive.



b.
A366174C01
3.073,0.75 3.385,0.906 0.313,0.156 10 false *a 3.073,0.969 3.385,1.125 0.313,0.156 10 false *b
*a 20°
*b 12°


Install the cylinder block water drain cock sub-assembly to the cylinder block sub-assembly as shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

Do not rotate the cylinder block water drain cock sub-assembly more than 1 revolution (360°) after tightening it to the specified torque.

·

Do not loosen the cylinder block water drain cock sub-assembly after setting it to the correct position.




c.

Install the cylinder block water drain cock plug to the cylinder block water drain cock sub-assembly.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 11415 74.INSTALL TAPER SCREW PLUG

a.
A366175C01
1.448,0.406 1.938,0.76 true 1.302,0.292 1.615,0.448 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to the taper screw plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Install the taper screw plug within 3 minutes of applying adhesive.



b.
A366047

Install the taper screw plug to the cylinder block sub-assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 12204 75.INSTALL PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 19100P 76.INSTALL SPARK PLUG

Hide 12108 77.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.
A366042

Install a new oil filler cap gasket to the oil filler cap sub-assembly.


b.
A408029

Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly LH.