Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › 2018.04–2021.02
RM33A0E _58 Vehicle Interior _065387 HEATING / AIR CONDITIONING _0319106 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  INSTALLATION  


PROCEDURE

Hide 1.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

w/ Claw:

i.

Engage the 2 claws.



b.

Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.


Hide 2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioner unit assembly when installing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.

·

When installing the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

Connect each connector.

E382593C01
0.167,0.167 0.417,0.417 0.25,0.25 12 true *A 2.417,0.167 2.667,0.417 0.25,0.25 12 true *B
*A for LHD *B for RHD
V113147

Install in this Direction - -



b.

Engage each clamp.


c.

Temporarily install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.


d.

Install the 4 bolts (A).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


e.

Connect the brake pedal assembly with the bolt (B).

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


f.

Temporarily install the nut.


g.

Install the 3 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


h.

Install the 2 hole plugs.


i.
E370262C01
0.302,0.729 0.427,0.521 false 0.219,0.729 0.531,0.885 0.313,0.156 10 false *a
*a Lip


Install a new cooler unit drain hose grommet.

NOTICE:
·

If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress.

·

Make sure that the entire lip of the cooler unit drain hose grommet is securely engaged to the vehicle body.




j.

Connect the drain cooler hose.


k.
E365335

Install the front floor mat to its original position as shown in the illustration.


l.
E377319C01
1.042,0.594 1.333,0.323 true 0.719,2.365 1.24,2.552 true 0.469,2.24 0.719,2.458 0.25,0.219 12 true *A 1.365,0.219 1.677,0.375 0.313,0.156 10 false *a
*A w/ Smart Entry and Start System
*a Lock Lever
V100135

Move in this Direction


Engage each clamp.


m.

Temporarily connect the connector and then move the lock lever in the direction indicated by the arrow to securely connect the connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



n.

Check that there is no looseness in the installed parts of the airbag sensor assembly.


o.

w/ Smart Entry and Start System:

i.

Connect the connector.



p.

for LHD:

i.

Engage each clamp.


ii.

Connect the connector holder with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


iii.

Connect the 3 earth wires with the 3 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


iv.

Connect the connector.



q.

for RHD:

i.

Engage the clamp.


ii.

Connect the connector holder with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


iii.

Engage each clamp.


iv.

Connect the 3 earth wires with the 3 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


v.

Connect each connector.



Hide 87201B 3.INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY

a.

Engage the 4 claws to install the No. 2 air duct sub-assembly.


Hide 4.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD)

Hide 82877 5.INSTALL ECU INTEGRATION BOX RH (for RHD)

Hide 55308B 6.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.

Install the No. 3 instrument panel to cowl brace sub-assembly with the bolt and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage each clamp.


Hide 55307C 7.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 2 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



c.

Engage each clamp.


d.

for LHD:

i.

Connect the relay block assembly with the bolt (B).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


ii.

Connect the earth wire with the bolt (A).

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)



e.

for RHD:

i.

Connect the earth wire with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)



Hide 55306A 8.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for LHD)

a.

Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



c.

Engage each clamp.


d.

Connect the earth wire with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


e.

w/ PTC Heater:

i.

Connect the earth wire with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)



Hide 55306A 9.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for RHD)

a.

Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



c.

Engage each clamp.


d.

Connect the relay block assembly with the bolt (B).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the earth wire with the bolt (A).

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 10.INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

for LHD:

i.

Tighten the 3 bolts, 2 screws and nut to install the air conditioner unit assembly.

E377335C01
0.667,0.302 0.823,0.5 0.156,0.198 10 true 1 3.01,0.333 3.167,0.531 0.156,0.198 10 true 3 6.333,0.333 6.49,0.531 0.156,0.198 10 true 2 5.344,4.833 5.5,5.031 0.156,0.198 10 true 6 3.01,4.667 3.167,4.865 0.156,0.198 10 true 5 0.667,5.219 0.823,5.417 0.156,0.198 10 true 4
V100135

Bolt
V100136

Screw
V100137

Nut - -


Torque:
Bolt : 9.8 N*m (100 kgf*cm, 87 in.*lbf)
Nut : 9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Tighten the bolts, screws and nut in the order shown in the illustration.




b.

for RHD:

i.

Tighten the 3 bolts, 2 screws and nut to install the air conditioner unit assembly.

E377353C01
3.01,0.333 3.167,0.531 0.156,0.198 10 true 1 0.594,0.385 0.75,0.583 0.156,0.198 10 true 2 5.417,0.385 5.573,0.583 0.156,0.198 10 true 3 4.01,5.135 4.167,5.333 0.156,0.198 10 true 4 5.333,5.135 5.49,5.333 0.156,0.198 10 true 5 1.667,5.167 1.823,5.365 0.156,0.198 10 true 6
V100135

Bolt
V100136

Screw
V100137

Nut - -


Torque:
Bolt : 9.8 N*m (100 kgf*cm, 87 in.*lbf)
Nut : 9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Tighten the bolts, screws and nut in the order shown in the illustration.




Hide 55215D 11.INSTALL NO. 3 DASH PANEL INSULATOR PAD

a.
E377308

Install the No. 3 dash panel insulator pad with 2 new clips as shown in the illustration.


Hide 58861B 12.INSTALL NO. 1 CONSOLE BOX DUCT

a.
E380282C01
0,0 0,0 false
V113147

Install in this Direction


Install the No. 1 console box duct as shown in the illustration.


Hide 58544B 13.INSTALL FLOOR CARPET BRACKET LH

a.
E377307C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw as shown in the illustration.


b.

Install the floor carpet bracket LH with the clip.


Hide 58543B 14.INSTALL FLOOR CARPET BRACKET RH

a.
E377306C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw as shown in the illustration.


b.

Install the floor carpet bracket RH with the clip.


Hide 87212G 15.INSTALL REAR NO. 3 AIR DUCT

a.

Engage the 2 claws to install the rear No. 3 air duct.


Hide 87212H 16.INSTALL REAR NO. 4 AIR DUCT

a.
E372140C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws to install the rear No. 4 air duct as shown in the illustration.


b.
E377301

Install the front floor carpet assembly to its original position as shown in the illustration.


c.

Engage the 2 guides.


d.

Install the 2 front floor carpet clips.


Hide 87212 17.INSTALL REAR NO. 1 AIR DUCT

a.

Engage the 2 claws to install the rear No. 1 air duct.


Hide 87212F 18.INSTALL REAR NO. 2 AIR DUCT

a.
E372142C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws to install the rear No. 2 air duct as shown in the illustration.


b.
E377303

Install the front floor carpet assembly to its original position as shown in the illustration.


c.

Engage the 2 guides.


d.

Install the front floor carpet clip.


e.

for LHD:

i.

Install the front floor carpet clip.



Hide 58569D 19.INSTALL FRONT FLOOR CAUTION PLATE COVER

a.
E372132C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guide and claw to install the front floor caution plate cover as indicated by the arrows, in the order shown in the illustration.


Hide 88625Q 22.INSTALL COOLER (ROOM TEMP. SENSOR) THERMISTOR (for Automatic Air Conditioning System)

a.

Connect the aspirator and connector to install the cooler (room temp. sensor) thermistor.


Hide 86740 23.INSTALL TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)

Hide 89111 24.INSTALL CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) (w/o Smart Entry and Start System)

Hide 82877 25.INSTALL ECU INTEGRATION BOX RH (for LHD)

Hide 26.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD)

Hide 8598A 27.INSTALL DOOR CONTROL BATTERY (w/ Door Control Battery)

Hide 89343C 28.INSTALL NO. 1 CLEARANCE WARNING BUZZER (for LHD)

Hide 29.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 45250 30.INSTALL STEERING COLUMN ASSEMBLY

Hide 33.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 88710E 34.CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the air conditioning tube and accessory assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the air conditioning tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the air conditioning tube and accessory assembly.


Hide 88707 35.CONNECT SUCTION PIPE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction pipe sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the suction pipe sub-assembly.


e.
E365731

Rotate the hook connector as shown in the illustration.


f.

Insert the tube joint into the fitting hole securely and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87245 36.CONNECT INLET HEATER WATER HOSE

a.

for A25A-FKS:

i.
E365737C01
1.75,2.813 2.167,2.396 false 0.073,2.229 0.323,2.479 0.25,0.25 10 false *a 2.156,2.271 2.469,2.427 0.313,0.156 10 false *b 1.635,4.49 1.948,4.646 0.313,0.156 10 false *c 1.188,1.281 1.354,1.448 0.167,0.167 10 true A
*a View A
*b Marking (White)
*c Clip Installation Angle (270°)


Connect the inlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the inlet heater water hose.




b.

except A25A-FKS:

i.
E371541C01
1.76,2.844 2.177,2.427 false 0.104,2.333 0.417,2.49 0.313,0.156 10 false *a 2.198,2.281 2.51,2.521 0.313,0.24 10 false *b 1.615,4.51 1.927,4.667 0.313,0.156 10 false *c 1.25,1.333 1.417,1.5 0.167,0.167 10 true A
*a View A
*b for 2AR-FE:
Marking (Red)
for 2GR-FKS:
Marking (Purple)
for 6AR-FSE:
Marking (Yellow)
*c Clip Installation Angle (270°)


Connect the inlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the inlet heater water hose.




Hide 87246 37.CONNECT OUTLET HEATER WATER HOSE

a.
E365735C01
1.74,2.813 2.156,2.396 false 0.073,2.063 0.323,2.313 0.25,0.25 10 false *a 2.167,2.281 2.479,2.438 0.313,0.156 10 false *b 1.604,2.167 1.917,2.323 0.313,0.156 10 false *c 1.104,0.958 1.271,1.125 0.167,0.167 10 true A
*a View A
*b for 2AR-FE:
Marking (Red)
for A25A-FKS:
Marking (Red)
for 2GR-FKS:
Marking (Purple)
for 6AR-FSE:
Marking (Yellow)
*c Clip Installation Angle (270°)


Connect the outlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the outlet heater water hose.



Hide 39.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 42.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT