Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  Image from Camera for Panoramic View Monitor is Abnormal  


DESCRIPTION

The display signal from each camera is transmitted to the radio and display receiver assembly via the television camera controller.

WIRING DIAGRAM

E372773E02
0.896,0.583 1.813,0.781 0.917,0.198 10 false NS+ 0.958,0.958 1.875,1.156 0.917,0.198 10 false NS- 0.865,1.406 1.781,1.604 0.917,0.198 10 false NSG 2.385,1.156 2.781,1.354 0.396,0.198 10 false * 1.375,0.396 1.771,0.594 0.396,0.198 10 false 28 1.302,0.594 1.698,0.792 0.396,0.198 10 false R123 1.385,0.792 1.781,0.979 0.396,0.188 10 false 26 1.375,1.198 1.771,1.396 0.396,0.198 10 false 27 3.01,0.5 3.406,0.698 0.396,0.198 10 false 28 3,0.885 3.396,1.083 0.396,0.198 10 false 29 3.271,0.594 3.667,0.792 0.396,0.198 10 false V+ 3.271,1.01 3.667,1.208 0.396,0.198 10 false V- 2.635,1.927 3.552,2.125 0.917,0.198 10 false K2 2.625,2.083 5.448,2.302 2.823,0.219 10 false Radio and Display Receiver Assembly 0.813,3.208 1.729,3.406 0.917,0.198 10 false BCB+ 0.813,4.01 1.729,4.208 0.917,0.198 10 false BCV+ 0.792,4.417 1.708,4.615 0.917,0.198 10 false BGND 0.781,4.823 1.698,5.021 0.917,0.198 10 false SGND 1.375,3.021 1.771,3.219 0.396,0.198 10 false 15 1.365,3.417 1.76,3.615 0.396,0.198 10 false 14 1.375,3.823 1.771,4.021 0.396,0.198 10 false 13 1.375,4.208 1.771,4.406 0.396,0.198 10 false 27 1.365,4.604 1.76,4.802 0.396,0.198 10 false 25 2.781,4.844 3.49,5.073 0.708,0.229 10 false B7 3.063,3.115 3.458,3.313 0.396,0.198 10 false 6 3.063,3.51 3.458,3.708 0.396,0.198 10 false 2 3.083,3.906 3.479,4.104 0.396,0.198 10 false 3 3.073,4.302 3.469,4.5 0.396,0.198 10 false 5 2.781,5.01 5.688,5.219 2.906,0.208 10 false Front Television Camera Assembly 5.26,5.594 6.708,5.854 1.448,0.26 10 false from ACC Relay 5.167,6.844 6.083,7.042 0.917,0.198 10 false ECU-ACC 3.927,6.688 4.844,6.885 0.917,0.198 10 false CB+ 4.302,6.573 4.698,6.771 0.396,0.198 10 false 6 2.729,7.531 3.646,7.729 0.917,0.198 10 false m4 2.719,7.688 4.917,8 2.198,0.313 10 false Rear Television Camera Assembly 3.073,6.188 3.469,6.385 0.396,0.198 10 false 3 3.073,6.583 3.469,6.781 0.396,0.198 10 false 2 3.083,6.99 3.479,7.188 0.396,0.198 10 false 5 1.396,6.094 1.792,6.292 0.396,0.198 10 false 1 1.406,6.49 1.802,6.688 0.396,0.198 10 false 2 1.406,6.885 1.802,7.083 0.396,0.198 10 false 9 0.927,6.271 1.844,6.469 0.917,0.198 10 false CV+ 0.927,6.677 1.844,6.875 0.917,0.198 10 false CV- 0.781,7.094 1.698,7.292 0.917,0.198 10 false CGND 0.094,8.021 2.104,8.479 2.01,0.458 10 false Television Camera Controller 5.604,7.844 6.521,8.042 0.917,0.198 10 false *: Shielded 0.854,3.604 1.771,3.802 0.917,0.198 10 false BCV- 1.313,3.229 1.708,3.427 0.396,0.198 10 false R124 2.375,4.583 2.771,4.781 0.396,0.198 10 false * 3.26,3.219 4.177,3.417 0.917,0.198 10 false BCB+ 3.26,3.615 4.177,3.813 0.917,0.198 10 false BCV- 3.26,4.021 4.177,4.219 0.917,0.198 10 false BCV+ 3.26,4.406 4.177,4.604 0.917,0.198 10 false BGND 3.26,6.281 4.177,6.479 0.917,0.198 10 false CV+ 3.26,6.677 4.177,6.875 0.917,0.198 10 false CV- 3.26,7.125 4.177,7.323 0.917,0.198 10 false CGND 1.302,6.302 1.698,6.5 0.396,0.198 10 false R124 2.375,6.854 2.771,7.052 0.396,0.198 10 false * 1.302,0.99 1.698,1.188 0.396,0.198 10 false R123 1.313,1.406 1.708,1.604 0.396,0.198 10 false R123 1.302,3.625 1.698,3.823 0.396,0.198 10 false R124 1.302,4.021 1.698,4.219 0.396,0.198 10 false R124 1.302,4.823 1.698,5.021 0.396,0.198 10 false R124 1.302,4.417 1.698,4.615 0.396,0.198 10 false R124 1.302,6.698 1.698,6.896 0.396,0.198 10 false R124 1.313,7.104 1.708,7.302 0.396,0.198 10 false R124

E372774E06
0.823,0.625 1.625,0.813 0.802,0.188 10 false RCB+ 0.865,1 1.781,1.198 0.917,0.198 10 false RCV- 0.833,1.406 1.75,1.604 0.917,0.198 10 false RCV+ 0.813,1.823 1.729,2.021 0.917,0.198 10 false RGND 0.813,2.219 1.729,2.417 0.917,0.198 10 false SGND 0.865,3.76 1.781,3.958 0.917,0.198 10 false LCB+ 0.896,4.146 1.813,4.344 0.917,0.198 10 false LCV- 0.844,4.552 1.76,4.75 0.917,0.198 10 false LCV+ 0.833,4.958 1.75,5.156 0.917,0.198 10 false LGND 0.813,5.365 1.729,5.563 0.917,0.198 10 false SGND 0.104,5.99 1.99,6.385 1.885,0.396 10 false Television Camera Controller 3.01,5.708 3.927,5.906 0.917,0.198 10 false O22 3.01,5.875 4.885,6.417 1.875,0.542 10 false Outer Rear View Mirror Assembly with Cover LH 5.583,5.292 7.042,5.781 1.458,0.49 10 false Side Television Camera Assembly LH 5.604,2.146 7.063,2.521 1.458,0.375 10 false Side Television Camera Assembly RH 3.063,2.563 3.979,2.76 0.917,0.198 10 false N24 3.042,2.719 4.615,3.198 1.573,0.479 10 false Outer Rear View Mirror Assembly with Cover RH 3.281,0.625 4.198,0.823 0.917,0.198 10 false RCB+ 3.271,1.042 4.188,1.24 0.917,0.198 10 false RCV- 3.271,1.438 4.188,1.635 0.917,0.198 10 false RCV+ 3.271,1.844 4.188,2.042 0.917,0.198 10 false RGND 3.271,2.24 4.188,2.438 0.917,0.198 10 false SGND 3.271,3.76 4.188,3.958 0.917,0.198 10 false LCB+ 3.281,4.167 4.198,4.365 0.917,0.198 10 false LCV- 3.271,4.563 4.188,4.76 0.917,0.198 10 false LCV+ 3.271,4.958 4.188,5.156 0.917,0.198 10 false LGND 3.281,5.365 4.198,5.563 0.917,0.198 10 false SGND 1.313,0.625 1.833,0.823 0.521,0.198 10 false R124 1.417,0.427 1.938,0.625 0.521,0.198 10 false 6 1.427,0.823 1.948,1.021 0.521,0.198 10 false 5 1.417,1.219 1.938,1.417 0.521,0.198 10 false 4 1.365,1.615 1.885,1.813 0.521,0.198 10 false 18 1.375,2.021 1.896,2.219 0.521,0.198 10 false 16 1.375,3.583 1.896,3.781 0.521,0.198 10 false 12 1.375,3.969 1.896,4.167 0.521,0.198 10 false 11 1.375,4.375 1.896,4.573 0.521,0.198 10 false 10 1.385,4.76 1.906,4.958 0.521,0.198 10 false 24 1.396,5.167 1.917,5.365 0.521,0.198 10 false 23 2.417,1.99 2.938,2.188 0.521,0.198 10 false * 3.073,0.521 3.594,0.719 0.521,0.198 10 false 2 3.021,0.917 3.542,1.115 0.521,0.198 10 false 12 3.073,1.323 3.594,1.521 0.521,0.198 10 false 1 3.021,1.719 3.542,1.917 0.521,0.198 10 false 13 3.042,2.115 3.563,2.313 0.521,0.198 10 false 14 3.063,3.667 3.583,3.865 0.521,0.198 10 false 2 3.042,4.052 3.563,4.25 0.521,0.198 10 false 12 3.094,4.479 3.615,4.677 0.521,0.198 10 false 1 3.021,4.823 3.542,5.021 0.521,0.198 10 false 13 3.052,5.26 3.573,5.458 0.521,0.198 10 false 14 5.219,6.104 6.135,6.302 0.917,0.198 10 false *: Shielded 2.417,5.135 2.938,5.333 0.521,0.198 10 false * 1.313,3.781 1.833,3.979 0.521,0.198 10 false R124 1.302,1.042 1.823,1.24 0.521,0.198 10 false R124 1.313,1.438 1.833,1.635 0.521,0.198 10 false R124 1.313,1.833 1.833,2.031 0.521,0.198 10 false R124 1.313,2.229 1.833,2.427 0.521,0.198 10 false R124 1.313,4.177 1.833,4.375 0.521,0.198 10 false R124 1.313,4.573 1.833,4.771 0.521,0.198 10 false R124 1.313,4.969 1.833,5.167 0.521,0.198 10 false R124 1.313,5.365 1.833,5.563 0.521,0.198 10 false R124

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



HINT:
Images may be unclear even in normal conditions if:
·

Electrical devices are used in the cabin (noise may occur in the image).

·

The camera lens is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).

·

The camera lens is dirty with snow, mud, etc.

·

A strong beam of light, such as a sunbeam or headlight, hits the camera.

·

It is too dark around the camera (at night, etc.).

·

The ambient temperature around the camera is either too high or too low.

·

The vehicle is tilted at a steep angle.

·

The television camera assembly lens is scratched.

·

The television camera assembly lens has drops of water on it or the humidity is high.

·

When the camera is used under fluorescent lights, sodium lights, or mercury lights, etc., the lights and the illuminated area may appear to flicker.



PROCEDURE

1.CHECK PANORAMIC VIEW MONITOR SYSTEM
a.

Check if the same malfunction occurs when the panoramic view monitor screen is displayed.


Result:
Result Proceed to
Rear view screen is not displayed. A
Front view screen is not displayed. B
Left side monitor screen is not displayed. C
Right side monitor screen is not displayed. D
Panoramic view monitor screen is not displayed. E



A

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - REAR TELEVISION CAMERA ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - FRONT TELEVISION CAMERA ASSEMBLY)

C

10.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH)

D

15.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH)

E

20.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - RADIO AND DISPLAY RECEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - REAR TELEVISION CAMERA ASSEMBLY)

OK

3.CHECK HARNESS AND CONNECTOR (ACC POWER SUPPLY - GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ACC POWER SUPPLY - GROUND)

OK

4.CHECK TELEVISION CAMERA CONTROLLER (CV-, CGND)

NG

4.CHECK TELEVISION CAMERA CONTROLLER (CV-, CGND)

OK

5.CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)

NG

5.CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)

OK

NG

6.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - FRONT TELEVISION CAMERA ASSEMBLY)

OK

7.CHECK TELEVISION CAMERA CONTROLLER (BCV-, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TELEVISION CAMERA CONTROLLER (BCV-, BGND)

NG

8.CHECK TELEVISION CAMERA CONTROLLER (BCB+, BGND)

OK

8.CHECK TELEVISION CAMERA CONTROLLER (BCB+, BGND)

OK

9.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)

NG

9.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)

OK

NG

10.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH)

OK

11.CHECK TELEVISION CAMERA CONTROLLER (LCV-, LGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK TELEVISION CAMERA CONTROLLER (LCV-, LGND)

OK

12.CHECK TELEVISION CAMERA CONTROLLER (LCB+, LGND)

NG

12.CHECK TELEVISION CAMERA CONTROLLER (LCB+, LGND)

OK

13.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND)

NG

13.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND)

OK

NG

14.REPLACE SIDE TELEVISION CAMERA ASSEMBLY LH
14.REPLACE SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


b.

Check if the same malfunction reoccurs when the side monitor screen is displayed.


Result:
Result Proceed to
Malfunction does not reoccur (returns to normal) A
Malfunction reoccurs B



A

END (SIDE TELEVISION CAMERA ASSEMBLY LH WAS DEFECTIVE)

B

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH

15.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH)

OK

16.CHECK TELEVISION CAMERA CONTROLLER (RCV-, RGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK TELEVISION CAMERA CONTROLLER (RCV-, RGND)

OK

17.CHECK TELEVISION CAMERA CONTROLLER (RCB+, RGND)

NG

17.CHECK TELEVISION CAMERA CONTROLLER (RCB+, RGND)

OK

18.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)

NG

18.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)

OK

NG

19.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH
19.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


b.

Check if the same malfunction reoccurs when the side monitor screen is displayed.


Result:
Result Proceed to
Malfunction does not reoccur (returns to normal) A
Malfunction reoccurs B



A

END (SIDE TELEVISION CAMERA ASSEMBLY RH WAS DEFECTIVE)

B

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH

20.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the R123 television camera controller connector.


b.

Disconnect the K2 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R123-28 (NS+) - K2-28 (V+) Always Below 1 Ω
R123-26 (NS-) - K2-29 (V-) Always Below 1 Ω
R123-27 (NSG) - Body ground Always Below 1 Ω
R123-28 (NS+) or K2-28 (V+) - Body ground Always 10 kΩ or higher
R123-26 (NS-) or K2-29 (V-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

21.CHECK TELEVISION CAMERA CONTROLLER (NS-, NSG)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK TELEVISION CAMERA CONTROLLER (NS-, NSG)
a.

Disconnect the R123 television camera controller connector.


b.
E372786C01
0.76,2.719 0.927,2.719 0.927,2.719 1.094,2.052 false 1.542,2.719 1.292,2.719 1.292,2.719 1.208,2.052 false 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 0.448,2.646 0.906,2.844 0.458,0.198 10 false NSG 1.625,2.635 2.083,2.833 0.458,0.198 10 false NS-
*a Component without harness connected
(Television Camera Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
27 (NSG) - Body ground Always Below 1 Ω
26 (NS-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

22.CHECK TELEVISION CAMERA CONTROLLER (NS+, NSG)

NG

22.CHECK TELEVISION CAMERA CONTROLLER (NS+, NSG)
a.

Remove the television camera controller with the connector still connected.


b.

Using an oscilloscope, check the waveform of the front television camera assembly.

HINT:

A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the television camera controller with the connector connected.


E372787C04
1.948,0.344 2.417,0.625 0.469,0.281 5,1.833 5.25,2.5 5.25,2.5 5.417,2.5 true 4.875,1.875 4.708,2.542 4.708,2.542 4.458,2.542 true 1.563,1.677 1.313,2.427 1.313,2.427 1.063,2.427 true 1.646,1.667 1.719,2.573 1.719,2.573 1.885,2.573 true 0.156,0.125 0.469,0.281 0.313,0.156 10 false *a 4.625,0.448 4.938,0.604 0.313,0.156 10 false *b 4.292,2.458 4.604,2.615 0.313,0.156 10 false *c 5.469,2.427 5.781,2.583 0.313,0.156 10 false *d 2.021,0.406 2.479,0.604 0.458,0.198 10 false R123 0.698,2.354 1.156,2.552 0.458,0.198 10 false NS+ 1.948,2.5 2.406,2.698 0.458,0.198 10 false NSG 4.104,1.323 4.563,1.521 0.458,0.198 10 false GND
*a Component with harness connected
(Television Camera Controller)
*b Waveform 1
*c Synchronization Signal *d Video Waveform


HINT:

The video waveform changes according to the image sent by the front television camera assembly.


Measurement Condition
Item Content
Terminal No. (Symbol) R123-28 (NS+) - R123-27 (NSG)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Engine switch on (IG), Panoramic image being displayed

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG