Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM (for 2AR-FE, 6AR-FSE LH Side) › 2018.04–2021.02
RM33A0E _53 Suspension _065361 FRONT SUSPENSION _0352044 FRONT LOWER SUSPENSION ARM(for 2AR-FE, 6AR-FSE LH Side) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for 2AR-FE, 6AR-FSE LH Side)  INSTALLATION  


PROCEDURE

Hide 48069 1.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly LH.


b.

Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front frame assembly with the 3 bolts and nut.


c.
C384625C01
0.667,1.771 0.781,1.771 0.781,1.771 1.031,1.188 true 2.375,1 2.698,1.156 0.323,0.156 10 false *a 2.646,0.948 2.958,1.104 0.313,0.156 10 false 3 1.177,0.323 1.313,0.5 0.135,0.177 10 true 2 0.25,0.74 0.385,0.917 0.135,0.177 10 true 1 0.49,1.688 0.813,1.844 0.323,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Ball Joint Lock Nut Wrench
V113148

Turn


Using a ball joint lock nut wrench, fully tighten the bolt (1).

Torque:
Specified tightening torque : 200 N*m (2039 kgf*cm, 148 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 400 mm (1.31 ft.)):

145.5 N*m (1484 kgf*cm, 107 ft.*lbf)




d.

Fully tighten the bolt (2) and then (3).

Torque:
Bolt (2) : 200 N*m (2039 kgf*cm, 148 ft.*lbf)
Bolt (3) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



e.

Slowly lower the engine assembly with transaxle using a jack and a wooden block.

NOTICE:
·

Do not position the wooden block under the oil pan.

·

Do not damage the components surrounding the engine assembly with transaxle.

·

Ensure that the jack and wooden block are stable.




f.

Connect the engine mounting insulator LH to the engine mounting bracket sub-assembly LH with the bolt and nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 12361A 2.CONNECT FRONT ENGINE MOUNTING INSULATOR

a.

Connect the front engine mounting insulator to the front frame assembly with the 3 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 48069 3.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Connect the front lower No. 1 suspension arm sub-assembly LH to the front lower ball joint assembly LH with the bolt and 2 nuts.

Torque:
92 N*m (938 kgf*cm, 68 ft.*lbf)


Hide 74404A 4.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 5.INSTALL BATTERY

Hide 17700 6.INSTALL AIR CLEANER ASSEMBLY

Hide 11.INSTALL FRONT WHEEL

Hide 12.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 13.PERFORM INITIALIZATION

Parking assist monitor system for Initialization:(Click here)
for Calibration:(Click here)
Panoramic view monitor system for Initialization:(Click here)
for Calibration:(Click here)
Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)