Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2018.04–2021.02
RM33A0E _58 Vehicle Interior _065379 THEFT DETERRENT / KEYLESS ENTRY _0328237 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Engine does not Start  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift lever is in P and the brake pedal is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the shift lever in N and the brake pedal depressed.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Engine does not start
Power Source Control
·

Stop Light Switch1

·

Steering Unlock Switch

·

Shift P Signal

·

Neutral SW/ Clutch SW

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Starter Request Signal

·

Power Supply Condition


Entry&Start
·

Immobiliser

·

Engine Start Request

·

L Code Check


Starting Control
·

Starter SW

·

Shift Position P or N

·

Ignition



WIRING DIAGRAM

B514096E01
0.958,0.344 1.417,0.542 0.458,0.198 10 false STP 5.885,0.344 6.344,0.542 0.458,0.198 10 false STP 1.344,0.365 1.802,0.563 0.458,0.198 10 false A24 1.74,0.365 2.198,0.563 0.458,0.198 10 false A23 2.135,0.365 2.594,0.563 0.458,0.198 10 false A22 2.531,0.365 2.99,0.563 0.458,0.198 10 false A78 1.396,0.167 1.708,0.365 0.313,0.198 10 false 21 1.792,0.156 2.104,0.354 0.313,0.198 10 false 27 2.208,0.146 2.396,0.354 0.188,0.208 10 false 9 2.615,0.146 2.813,0.354 0.198,0.208 10 false 9 1.417,0.573 1.729,0.771 0.313,0.198 10 false *1 1.813,0.563 2.125,0.76 0.313,0.198 10 false *2 2.208,0.563 2.521,0.76 0.313,0.198 10 false *3 2.615,0.563 2.927,0.76 0.313,0.198 10 false *4 5.708,0.26 5.865,0.458 0.156,0.198 10 false 4 5.781,0.708 6.24,0.906 0.458,0.198 10 false K27 5.781,0.854 6.917,1.542 1.135,0.688 10 false Shift Lock Control Unit Assembly 5.896,1.76 6.354,1.958 0.458,0.198 10 false STP 5.635,1.667 5.948,1.865 0.313,0.198 10 false 42 5.5,2.125 5.958,2.323 0.458,0.198 10 false A34 5.5,2.26 7.063,2.854 1.563,0.594 10 false Skid Control ECU (Brake Actuator Assembly) 2.354,2.354 4.188,2.552 1.833,0.198 10 false from Battery 1.615,2.5 2.229,2.698 0.615,0.198 10 false STOP 2.635,2.938 2.792,3.135 0.156,0.198 10 false B 3.396,3.052 3.552,3.344 0.156,0.292 10 false L 2.625,3.354 3.083,3.552 0.458,0.198 10 false GND 2.448,2.854 2.604,3.052 0.156,0.198 10 false 7 2.438,3.25 2.594,3.448 0.156,0.198 10 false 2 3.604,3.063 3.76,3.26 0.156,0.198 10 false 3 3,3.146 3.313,3.344 0.313,0.198 10 false IC 2.438,3.698 2.896,3.896 0.458,0.198 10 false A37 2.427,3.823 6.406,4.021 3.979,0.198 10 false Stop Light Switch Assembly 1.344,4.323 1.802,4.521 0.458,0.198 10 false A24 1.75,4.323 2.208,4.521 0.458,0.198 10 false C96 2.135,4.323 2.594,4.521 0.458,0.198 10 false A22 2.531,4.323 2.99,4.521 0.458,0.198 10 false A78 2.531,5.792 2.99,5.99 0.458,0.198 10 false A78 2.573,4.51 2.885,4.708 0.313,0.198 10 false *4 2.573,6 2.885,6.198 0.313,0.198 10 false *4 2.188,4.531 2.5,4.729 0.313,0.198 10 false *3 2.198,5.979 2.51,6.177 0.313,0.198 10 false *3 1.813,4.531 2.125,4.729 0.313,0.198 10 false *2 1.802,5.99 2.115,6.188 0.313,0.198 10 false *2 1.396,4.531 1.708,4.729 0.313,0.198 10 false *1 1.396,5.99 1.708,6.188 0.313,0.198 10 false *1 1.344,5.781 1.802,5.979 0.458,0.198 10 false A24 1.74,5.781 2.198,5.979 0.458,0.198 10 false A23 2.135,5.771 2.594,5.969 0.458,0.198 10 false A22 1.396,4.104 1.708,4.302 0.313,0.198 10 false 23 1.75,4.115 2.208,4.313 0.458,0.198 10 false 106 2.198,4.115 2.51,4.313 0.313,0.198 10 false 23 2.573,4.125 2.885,4.323 0.313,0.198 10 false 57 2.875,4.76 3.031,4.958 0.156,0.198 10 false B 3.167,4.75 3.323,5.042 0.156,0.292 10 false L 2.604,5.031 2.76,5.229 0.156,0.198 10 false P 2.604,5.302 2.76,5.5 0.156,0.198 10 false N 1.385,5.573 1.698,5.771 0.313,0.198 10 false 30 1.781,5.573 2.094,5.771 0.313,0.198 10 false 43 2.188,5.573 2.5,5.771 0.313,0.198 10 false 29 2.573,5.583 2.885,5.781 0.313,0.198 10 false 29 2.979,4.458 3.135,4.656 0.156,0.198 10 false 4 3.24,5.573 3.396,5.771 0.156,0.198 10 false 9 3.375,4.719 3.833,4.917 0.458,0.198 10 false C55 3.385,4.865 4.729,5.542 1.344,0.677 10 false Park/Neutral Position Switch Assembly 6.552,3.344 6.865,3.542 0.313,0.198 10 false IC 6.552,4.448 6.865,4.646 0.313,0.198 10 false IC 5.542,3.156 5.854,3.354 0.313,0.198 10 false R8 5.521,4.323 5.979,4.521 0.458,0.198 10 false A13 5.5,5.781 5.958,5.979 0.458,0.198 10 false A13 5.875,3.063 6.49,3.26 0.615,0.198 10 false STP1 5.875,4.208 6.49,4.406 0.615,0.198 10 false STAR 6.219,3.781 6.531,3.979 0.313,0.198 10 false +B 5.885,5.781 6.344,5.979 0.458,0.198 10 false STA 5.542,2.938 5.854,3.135 0.313,0.198 10 false 25 5.583,4.094 5.708,4.344 0.125,0.25 10 false 9 5.542,5.563 5.854,5.76 0.313,0.198 10 false 20 0.896,4.302 1.354,4.5 0.458,0.198 10 false NSW 0.948,5.76 1.406,5.958 0.458,0.198 10 false STA 0.646,6.219 1.104,6.417 0.458,0.198 10 false ECM 3.24,6.042 3.396,6.24 0.156,0.198 10 false 2 3.51,6.052 3.667,6.25 0.156,0.198 10 false 5 5.531,6.24 7.083,7 1.552,0.76 10 false Certification ECU (Smart Key ECU Assembly) 4.094,6.104 5.323,6.302 1.229,0.198 10 false ST NO. 1 3.5,6.75 3.656,6.948 0.156,0.198 10 false 3 3.229,6.74 3.385,6.938 0.156,0.198 10 false 1 3.115,7.167 3.271,7.365 0.156,0.198 10 false 1 3.125,7.417 3.281,7.615 0.156,0.198 10 false 1 3.323,7.177 3.781,7.375 0.458,0.198 10 false C61 3.333,7.406 3.792,7.604 0.458,0.198 10 false C64 3.688,7.417 4,7.615 0.313,0.198 10 false *1 3.688,7.177 4.604,7.375 0.917,0.198 10 false *2*3*4 4.427,7.802 4.74,8 0.313,0.198 10 false D1 4.792,7.802 5.25,8 0.458,0.198 10 false C74 4.438,8.01 4.75,8.208 0.313,0.198 10 false *1 4.75,7.99 5.667,8.188 0.917,0.198 10 false *2*3*4 4.458,7.594 4.615,7.792 0.156,0.198 10 false 1 4.865,7.594 5.021,7.792 0.156,0.198 10 false 1 5.781,7.802 6.917,8.104 1.135,0.302 10 false from Battery 4.167,7.667 4.323,7.865 0.156,0.198 10 false B 3.479,7.635 3.792,7.833 0.313,0.198 10 false ST 3.135,8.365 5.583,8.563 2.448,0.198 10 false Starter Assembly 0.219,8.375 2.51,8.573 2.292,0.198 10 false *4: for 6AR-FSE 0.219,8.031 2.365,8.229 2.146,0.198 10 false *3: for 2AR-FE 0.219,7.719 2.51,7.917 2.292,0.198 10 false *2: for 2GR-FKS 0.208,7.396 2.656,7.594 2.448,0.198 10 false *1: for A25A-FKS 2.823,6.375 3.135,6.573 0.313,0.198 10 false ST

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the smart entry and start system (for Start Function) has been disabled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:
·

If the engine switch is changed from on (IG) to on (ACC) with the shift lever in any position other than P, and then the shift lever is moved to P and the engine switch is pressed with the brake pedal depressed, the engine switch will turn off.

·

If the brake pedal is repeatedly depressed while the engine is stopped, the brake booster pressure will be released and the force required to depress the brake pedal to illuminate the stop lights will increase.



PROCEDURE

1.CHECK ENGINE CRANKING OPERATION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch and check that the engine cranks.


Result:
Result Proceed to
Engine cranks and initial combustion occurs A
Engine cranks but initial combustion does not occur B
Engine does not crank C



A

B

C

2.CHECK ENGINE SWITCH CONDITION
2.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

With the brake pedal released, check that pressing the engine switch causes the power source mode to change.


Result:
Result Proceed to
Power source mode changes : Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) or on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D



A

3.READ VALUE USING GTS (STOP LIGHT SWITCH1)

B

C

D

3.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)

NG

12.INSPECT STOP LIGHT SWITCH ASSEMBLY
4.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)
a.

Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Shift position (P and N) OFF or ON OFF: Shift lever in any position other than P or N
ON: Shift lever in P or N
·

Use this item to determine if the park/neutral position switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6
Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position P or N Park/Neutral position switch status OFF or ON OFF: Shift lever not in P or N
ON: Shift lever in P or N
When OFF is displayed, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Shift Position P or N
50003 221 2
OK:

The GTS display changes correctly in response to the shift lever operation.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

14.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
5.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Engine start request signal status OFF or ON OFF: The engine switch is not pressed
ON: With the shift lever in P and the brake pedal depressed, the engine switch is pressed and held
·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch.


OK:

The GTS display changes correctly in response to the engine switch operation.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (STARTER SW)

NG

16.CHECK STEERING LOCK FUNCTION
6.READ VALUE USING GTS (STARTER SW)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Enter the following menus: Body Electrical / Starting Control / Data List.


d.

According to the display on the GTS, read the Data List while pressing the engine switch with the brake pedal depressed.

Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter operation request OFF or ON OFF: Starter operation not requested
ON: Starter operation requested
When OFF is displayed, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Starter SW
50003 221 1
OK:

The GTS display changes.



Result:
Proceed to
OK
NG



OK

7.INSPECT ST RELAY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.INSPECT ST RELAY

OK

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

NG

REPLACE ST RELAY

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
a.
C378519C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY
(ST Relay Holder)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Engine room relay block and junction block assembly ST relay terminal 2 - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (ST RELAY - BATTERY AND GROUND)

NG

17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (ST RELAY - BATTERY AND GROUND)
a.
C378519C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY
(ST Relay Holder)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Engine room relay block and junction block assembly ST relay terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Engine room relay block and junction block assembly ST relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST RELAY)
a.

Disconnect the C64*1 or C61*2 starter assembly connector.

*1: for A25A-FKS

*2: except A25A-FKS



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for A25A-FKS
Tester Connection Condition Specified Condition
Engine room relay block and junction block assembly ST relay terminal 3 - C64-1 Always Below 1 Ω
Engine room relay block and junction block assembly ST relay terminal 3 or C64-1 - Other terminals and body ground Always 10 kΩ or higher

except A25A-FKS
Tester Connection Condition Specified Condition
Engine room relay block and junction block assembly ST relay terminal 3 - C61-1 Always Below 1 Ω
Engine room relay block and junction block assembly ST relay terminal 3 or C61-1 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)
a.

Disconnect the D1*1 or C74*2 starter assembly connector.

*1: for A25A-FKS

*2: except A25A-FKS



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for A25A-FKS
Tester Connection Condition Specified Condition
D1-1 - Body ground Always 11 to 14 V

except A25A-FKS
Tester Connection Condition Specified Condition
C74-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A37 stop light switch assembly connector.


b.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the A24*1, A23*2, A22*3 or A78*4 ECM connector.


d.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


e.

Disconnect the K27 shift lock control unit assembly connector.

*1: for A25A-FKS

*2: for 2GR-FKS

*3: for 2AR-FE

*4: for 6AR-FSE



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R8-25 (STP1) - A37-3 (L) Always Below 1 Ω
R8-25 (STP1) or A37-3 (L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the A13 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-9 (STAR) - C55-4 (B) Always Below 1 Ω
A13-9 (STAR) or C55-4 (B) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK STEERING LOCK FUNCTION
a.

Check that the steering unlocks when the engine switch is turned on (ACC).

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B424432C21
1.458,0.073 1.875,0.323 0.417,0.25 1.385,1.802 1.604,1.802 1.604,1.802 1.604,0.969 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.542,0.104 1.854,0.302 0.313,0.198 10 false A13 0.99,1.719 1.917,1.917 0.927,0.198 10 false STAR
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-9 (STAR) - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the A13 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the C55 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-9 (STAR) - C55-4 (B) Always Below 1 Ω
A13-9 (STAR) or C55-4 (B) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Install the ST relay to the engine room relay block and junction block assembly.


b.
B424432C20
1.458,0.073 1.875,0.323 0.417,0.25 1.063,1.927 1.302,1.927 1.302,1.927 1.302,1.094 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.542,0.104 1.854,0.302 0.313,0.198 10 false A13 0.771,1.833 1.083,2.031 0.313,0.198 10 false STA
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-20 (STA) - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
a.

Disconnect the A13 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-20 (STA) - 2 (ST relay) Always Below 1 Ω
A13-20 (STA) or 2 (ST relay) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C55-9 (L) - 2 (ST relay) Always Below 1 Ω
C55-9 (L) or 2 (ST relay) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR