Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0263  Cylinder 1 Contribution / Balance  P0266  Cylinder 2 Contribution / Balance  P0269  Cylinder 3 Contribution / Balance  P0272  Cylinder 4 Contribution / Balance  


DESCRIPTION

Refer to DTC P0200 (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>P0200).

DTC No. DTC Detection Condition Trouble Area
P0263
P0266
P0269
P0272
Conditions (a) and (b) are met more than 200 times with engine speed 500 to 1000 rpm:
(1 trip detection logic)
(a) Engine coolant temperature: 60°C (140°F) or more
(b) Difference of compensation value between cylinders: 15 mm3/sec. or more
·

Open or short in injector driver assembly circuit

·

Injector assembly

·

Injector driver assembly

·

ECM

·

Compression



HINT:

These DTCs indicate a malfunction related to the primary circuit.

·

If DTC P0263 is displayed, check the injector No. 1 circuit.

·

If DTC P0266 is displayed, check the injector No. 2 circuit.

·

If DTC P0269 is displayed, check the injector No. 3 circuit.

·

If DTC P0272 is displayed, check the injector No. 4 circuit.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of this circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION.



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0263, P0266, P0269 AND P0272)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Rear the DTCs.


Result:
Result Proceed to
P0263, P0266, P0269 and/or P0272 A
P0263, P0266, P0269 and/or P0272 and other DTCs B



A

2.CHANGE TO KNOWN GOOD INJECTOR ASSEMBLY

B

2.CHANGE TO KNOWN GOOD INJECTOR ASSEMBLY
a.

Change the installed injector assembly to a known good injector assembly.


b.

Input the injector compensation code (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).


Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS (P0263, P0266, P0269 AND P0272)
3.CHECK WHETHER DTC OUTPUT RECURS (P0263, P0266, P0269 AND P0272)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.



e.

Warm up the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.


g.

Read the DTCs.

Result:
Result Proceed to
Same DTCs are output (same as DTCs that were cleared) A
Other DTCs are output B


HINT:
·

If a DTC for a different cylinder is stored when the injector assembly has been switched with a known good one from a different cylinder, the injector assembly may be malfunctioning.

·

If no DTC is stored after the injector assembly has been replaced, the injector assembly may be malfunctioning.

·

If the same DTC is stored again even after replacing the injector assembly with a known good injector assembly, the ECM, injector driver assembly, engine or wire harness may be malfunctioning.





A

4.INSPECT INJECTOR DRIVER ASSEMBLY (INJECTOR ASSEMBLY RESISTANCE)

B

9.CHECK INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER FOR DEPOSITS
4.INSPECT INJECTOR DRIVER ASSEMBLY (INJECTOR ASSEMBLY RESISTANCE)
a.
A187353E04
0.438,3.396 0.875,3.677 0.438,0.281 0.448,1.208 0.875,1.479 0.427,0.271 1.948,1.635 2.375,2.01 true 1.948,1.375 2.396,1.031 true 1.469,3.719 1.042,4.083 true 1.74,3.729 2.104,4.094 true 1.448,3.427 0.917,2.948 true 1.74,3.396 2.167,2.948 true 0.302,0.24 0.49,0.427 0.188,0.188 10 false *1 0.521,3.458 0.844,3.635 0.323,0.177 10 false B98 0.521,1.271 0.865,1.469 0.344,0.198 10 false B96 2.417,1.948 2.813,2.135 0.396,0.188 10 false INJ2 2.448,0.906 2.844,1.094 0.396,0.188 10 false INJ3 0.677,4.031 1.063,4.229 0.385,0.198 10 false INJ4 2.198,4.073 2.573,4.25 0.375,0.177 10 false INJ1 0.51,2.771 0.938,2.927 0.427,0.156 10 false COM1 2.156,2.781 2.646,2.969 0.49,0.188 10 false COM2

Disconnect the injector driver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B98-5 (INJ1) - B98-1 (COM1) 20°C (68°F) 0.85 to 1.05 Ω
B96-4 (INJ2) - B98-2 (COM2) 20°C (68°F) 0.85 to 1.05 Ω
B96-2 (INJ3) - B98-2 (COM2) 20°C (68°F) 0.85 to 1.05 Ω
B98-4 (INJ4) - B98-1 (COM1) 20°C (68°F) 0.85 to 1.05 Ω


Text in Illustration
*1 Front view of wire harness connector
(to Injector Driver Assembly)


c.

Reconnect the injector driver assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER ASSEMBLY - ECM)

NG

8.INSPECT INJECTOR ASSEMBLY
5.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER ASSEMBLY - ECM)
a.

Disconnect the injector driver assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B95-6 (#10) - B59-24 (#1) Always Below 1 Ω
B95-2 (#20) - B59-23 (#2) Always Below 1 Ω
B95-1 (#30) - B59-22 (#3) Always Below 1 Ω
B95-3 (#40) - B59-21 (#4) Always Below 1 Ω
B96-1 (INJF) - B59-25 (INJF) Always Below 1 Ω
B95-6 (#10) or B59-24 (#1) - Body ground Always 10 kΩ or higher
B95-2 (#20) or B59-23 (#2) - Body ground Always 10 kΩ or higher
B95-1 (#30) or B59-22 (#3) - Body ground Always 10 kΩ or higher
B95-3 (#40) or B59-21 (#4) - Body ground Always 10 kΩ or higher
B96-1 (INJF) or B59-25 (INJF) - Body ground Always 10 kΩ or higher



d.

Reconnect the injector driver assembly connectors.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

6.INSPECT ECM (OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ECM (OUTPUT VOLTAGE)
a.

While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

A427250E01
0.854,1.125 1.26,1.406 0.406,0.281 1.469,1.125 1.875,1.406 0.406,0.281 0.542,2.823 0.938,1.885 true 0.906,2.635 0.979,1.896 true 1.406,2.802 1.021,1.906 true 1.781,2.615 1.073,1.906 true 2.563,2.604 1.135,1.896 true 3.156,2.583 1.417,1.75 true 0.927,1.188 1.25,1.385 0.323,0.198 10 false B59 1.552,1.177 1.875,1.375 0.323,0.198 10 false B60 0.146,2.854 0.792,3.052 0.646,0.198 10 false 25 (INJF) 0.719,2.667 1.24,2.865 0.521,0.198 10 false 24 (#1) 1.25,2.813 1.771,3.01 0.521,0.198 10 false 22 (#3) 1.729,2.625 2.25,2.823 0.521,0.198 10 false 23 (#2) 2.406,2.635 2.927,2.833 0.521,0.198 10 false 21 (#4) 3.01,2.625 3.531,2.823 0.521,0.198 10 false 7 (E1) 5.958,0.063 6.615,0.26 0.656,0.198 10 false 5 V/DIV. 6.198,0.51 6.573,0.688 0.375,0.177 10 false GND 6.198,0.833 6.573,1.01 0.375,0.177 10 false GND 6.198,1.146 6.573,1.323 0.375,0.177 10 false GND 6.198,1.458 6.573,1.635 0.375,0.177 10 false GND 4.156,0.521 4.396,0.698 0.24,0.177 10 false #1 4.156,0.823 4.396,1 0.24,0.177 10 false #3 4.156,1.146 4.396,1.323 0.24,0.177 10 false #4 4.156,1.458 4.396,1.635 0.24,0.177 10 false #2 4.792,1.729 5.823,1.927 1.031,0.198 10 false 20 msec./DIV. 0.271,0.292 0.594,0.49 0.323,0.198 10 false *a 5.99,1.927 6.646,2.125 0.656,0.198 10 false 2 V/DIV. 6.198,2.698 6.573,2.875 0.375,0.177 10 false GND 4.823,3.438 5.854,3.635 1.031,0.198 10 false 20 msec./DIV. 4.063,2.542 4.406,2.729 0.344,0.188 10 false INJF

Text in Illustration
*a Component with harness connected
(ECM)
- -

Standard:
Tester Connection Condition Specified Condition
B59-24 (#1) - B60-7 (E1) Idling Correct waveform appears as shown
B59-23 (#2) - B60-7 (E1) Idling Correct waveform appears as shown
B59-22 (#3) - B60-7 (E1) Idling Correct waveform appears as shown
B59-21 (#4) - B60-7 (E1) Idling Correct waveform appears as shown
B59-25 (INJF) - B60-7 (E1) Idling Correct waveform appears as shown



Result:
Result Proceed to
#1 to #4 is normal
INJF is abnormal
A
#1 to #4 is abnormal
INJF is normal
B
#1 to #4 and INJF are normal C



A

REPLACE INJECTOR DRIVER ASSEMBLY

B

C

7.CHECK CYLINDER COMPRESSION PRESSURE
7.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder (Click hereEngine / Hybrid System>N04C-UH (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

8.INSPECT INJECTOR ASSEMBLY
a.
A081503E33
0.135,0.104 0.354,0.292 0.219,0.188 10 false *a

Disconnect the injector assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 0.85 to 1.05 Ω


Text in Illustration
*a Front view of wire harness connector
(to Injector Assembly)


c.

Reconnect the injector assembly connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EDU - INJECTOR ASSEMBLY)

NG

9.CHECK INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER FOR DEPOSITS
a.

Remove the injector assembly of malfunction cylinder.


b.

Check the injector assembly for any deposits.

OK:

No deposits.


Result:
Result Proceed to
Deposits A
No deposits B


HINT:

If excessive deposits are present on the head of the injector assembly, a malfunction of something other than the injector assembly has resulted in an increase of the fuel injection compensation volume. First perform the troubleshooting procedure for black smoke.




A

B