Home › Engine / Hybrid System › 14B (ENGINE MECHANICAL) › TIMING GEAR › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073170 14B ENGINE MECHANICAL _0356052 TIMING GEAR A

14B ENGINE MECHANICAL  TIMING GEAR  TIMING GEARS AND CAMSHAFT INSTALLATION  


PROCEDURE

Hide 1.INSTALL CRANKSHAFT TIMING GEAR

a.
A430622

Check the set key on crankshaft facing upward.

If not, then turn the crankshaft with a crankshaft pulley mount bolt.


b.
A430623

Put the timing gear on the crankshaft with the "1" timing mark of the timing gear facing forward.


c.

Align the timing gear set key with the key groove of the timing gear.


d.

Using SST and a hammer, tap in the timing gear.

SST
09608-06041  


Hide 2.INSTALL CAMSHAFT TIMING GEAR AND CAMSHAFT ASSEMBLY

A430624

a.

Insert the camshaft into the cylinder block.

NOTICE:

Be careful not to damage the camshaft bearings.



b.

Install and torque the 2 bolts.

Torque:

18.5 N*m (189 kgf*cm, 14 ft.*lbf)



Hide 3.INSTALL IDLER GEAR SHAFT

a.
A430625

Temporarily install the idle gear shaft with the union bolt.

NOTICE:

Do not tighten the union bolt.



Hide 4.INSTALL IDLE GEAR

a.
A430626

Align the idle gear timing marks "1" and "2" with the crankshaft gear timing mark "1" and camshaft gear timing mark "2" respectively, and mesh the gears.


b.
A430627

Apply a light coat of engine oil on the threads and under the bolt heads.


c.

Install the thrust plate with the 2 bolts. Torque the bolts.

Torque:

47.5 N*m (484 kgf*cm, 35 ft.*lbf)



d.
A430628

Check that the oil nozzle is in the position shown.


Hide 5. TORQUE UNION BOLT FOR IDLE GEAR SHAFT

Torque:

11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 6.INSTALL INJECTION PUMP DRIVE GEAR

a.
A430629

Apply MP grease to the drive gear spline, bearing and injection pump spline.


b.

Align the spline toothless portions of the injection pump drive gear and injection pump, and install the injection pump drive gear.


c.
A430630

Using SST, align the idle gear timing mark "o" with the injection pump drive gear timing mark "o", and mesh the gears.

SST
09960-10010  (09962-01000, 09963-01000)


Hide 7.INSTALL VACUUM PUMP

a.

Install 2 new O-rings to vacuum pump.


b.

Install the vacuum pump with the 2 bolts.

Torque:

39 N*m (400 kgf*cm, 29 ft.*lbf)



Hide 8.CHECK TIMING GEAR BACKLASH

Click hereEngine / Hybrid System>14B (ENGINE MECHANICAL)>TIMING GEAR>TIMING GEARS AND CAMSHAFT REMOVAL

Standard backlash:

0.058 - 0.162 mm (0.0023 - 0.0064 in.)


Maximum backlash:

0.30 mm (0.0118 in.)


Hide 9.CHECK IDLE GEAR THRUST CLEARANCE

Click hereEngine / Hybrid System>14B (ENGINE MECHANICAL)>TIMING GEAR>TIMING GEARS AND CAMSHAFT REMOVAL

Standard thrust clearance:

0.060 - 0.170 mm (0.0024 - 0.0067 in.)


Maximum thrust clearance:

0.30 mm (0.0118 in.)


Hide 10.INSTALL TIMING GEAR COVER

a.

Install a new gasket and the timing gear cover.


b.

Align the 2 knock pins of the oil pump and lightly tap in the timing gear cover, using a plastic-faced hammer.


c.
A430631

Install the bracket and 16 (BU) or 15 (BB) mount bolts.

Torque:
14 mm head:

44 N*m (449 kgf*cm, 32 ft.*lbf)

12 mm head:

21 N*m (214 kgf*cm, 15 ft.*lbf)


HINT:

Each bolt length is indicated in the illustration.


Bolt length

A 80 mm (3.15 in.) for 14 mm head

B 77 mm (3.03 in.) for 12 mm head

C 40 mm (1.57 in.) for 12 mm head

D 35 mm (1.38 in.) for 12 mm head



Hide 12.INSTALL OIL DIPSTICK GUIDE AND DIPSTICK

Hide 13.INSTALL RADIATOR PIPE

a.

Connect the radiator hose to the water pump.


b.

Install the radiator pipe with the 2 bolts.

Torque:

21 N*m (214 kgf*cm, 15 ft.*lbf)



Hide 14.INSTALL CRANKSHAFT PULLEY

a.

Align the pulley set key with the key groove of the pulley.


b.
A430632

Using SST and a hammer, tap in the pulley.

SST
09608-06041  


c.

Apply a light coat of engine oil on the threads and under the bolt head.


d.
A430633

Using SST, install and torque the pulley mount bolt.

BU

SST
09213-58012  (90201-08131, 91111-50845)
09330-00021  

BB

SST
09213-58012  (90105-08076)
09330-00021  

Torque:

294 N*m (3000 kgf*cm, 217 ft.*lbf)



Hide 15.DISPLACE VALVE LIFTERS

a.
A430634

Remove bolt A and let the lifter slide down.


b.

Install bolts A and B with new gaskets.

Torque:
Bolt A:

7.5 N*m (76 kgf*cm, 66 in.*lbf)

Bolt B:

37.5 N*m (382 kgf*cm, 28 ft.*lbf)


HINT:

When installing bolt B, check that the hole for bolt B is aligned with long hole C of valve lifter.



c.

Check that the valve lifter can move up and down within the limits of long hole C.

NOTICE:

Be careful not to scratch the valve lifter.



Hide 17.INSTALL EXHAUST MANIFOLD HEAT INSULATOR (3B, 14B)

Hide 18.INSTALL TURBOCHARGER AND EXHAUST MANIFOLD ASSEMBLY (15B-FT)

Hide 23600 20.INSTALL INJECTION NOZZLES (14B, 15B-F, 15B-FT)

Hide 21.INSTALL WATER PUMP PULLEY, FAN, FLUID COUPLING ASSEMBLY (FAN SPACER AND FAN) AND DRIVE BELT(S)

Hide 22.START ENGINE AND CHECK FOR LEAKS

Hide 23.CHECK ENGINE OIL LEVEL