Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS (for Double Swing Out Type) › 2017.01–2019.08
RM2850E _59 Vehicle Exterior _073195 WINDOW / GLASS _0356207 BACK WINDOW GLASS(for Double Swing Out Type) A

WINDOW / GLASS  BACK WINDOW GLASS(for Double Swing Out Type)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.

·

Use the same procedure for RH and LH sides.

·

The procedure listed below is for LH side.



PROCEDURE

Hide 68294A 1.INSTALL BACK DOOR GLASS ADHESIVE DAM

a.

Using non-residue solvent, clean the back door glass adhesive dam installation surface of the back window corner glass LH.


b.

Install the glass primer to the back door glass adhesive dam installation surface of the back window corner glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back door glass adhesive dam.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the 3 back door glass adhesive dams to the back window corner glass LH as shown in the illustration.

B471611E01
1.031,2 0.75,2.115 0.75,2.115 0.781,2.031 true 3.271,0.75 3.458,0.938 3.458,0.938 3.281,0.969 true 3.365,1.74 3.729,1.854 3.729,1.854 3.375,1.969 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.125,1.635 1.281,1.802 0.156,0.167 10 true B 1.208,2.177 1.365,2.344 0.156,0.167 10 true B 2.979,0.479 3.135,0.646 0.156,0.167 10 true A 3.5,0.458 3.656,0.625 0.156,0.167 10 true A 0.583,2.073 0.792,2.24 0.208,0.167 10 false *b 3.51,0.906 3.719,1.073 0.208,0.167 10 false *b 3.781,1.781 3.99,1.948 0.208,0.167 10 false *b 5,0.115 5.313,0.292 0.313,0.177 10 false A-A 5.042,1.469 5.354,1.646 0.313,0.177 10 false B-B 5.729,0.26 5.854,0.438 0.125,0.177 10 false a 5.75,1.615 5.875,1.792 0.125,0.177 10 false b

Text in Illustration
*a Back Side *b Ceramic Notch

Standard:
Area Specified Condition
a 20.0 mm (0.787 in.)
b 19.5 mm (0.768 in.)



Hide 64828 2.INSTALL BACK WINDOW GLASS CLIP LH

a.

Using non-residue solvent, clean the back window glass clip LH installation surface of the back window corner glass LH.


b.

Install the glass primer to the back window glass clip LH installation surface of the back window corner glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back window glass clip LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.
B471612E01
0.542,1.177 0.469,0.781 0.469,0.781 1.083,1.177 true 0.552,1.531 0.854,1.917 0.854,1.917 1.083,1.531 true 2.646,1.125 2.833,1.427 2.833,1.427 2.969,1.135 true 2.625,0.563 3.052,0.281 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 3.083,0.208 3.302,0.375 0.219,0.167 10 false *b 2.75,1.448 2.969,1.615 0.219,0.167 10 false *b 0.771,1.958 0.99,2.125 0.219,0.167 10 false *b 0.292,0.625 0.51,0.792 0.219,0.167 10 false *b

Install the 2 back window glass clips LH to the back window corner glass LH as shown in the illustration.

Text in Illustration
*a Back Side
*b Ceramic Notch


Hide 64813D 3.INSTALL BACK WINDOW GLASS ADHESIVE DAM

a.

Using non-residue solvent, clean the back window glass adhesive dam installation surface of the back window corner glass LH.


b.

Install the glass primer to the back window glass adhesive dam installation surface of the back window corner glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back window glass adhesive dam.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.
B471613E01
0.698,1.667 0.344,1.052 0.344,1.052 0.667,0.573 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.156,0.979 0.375,1.146 0.219,0.167 10 false *b 1.479,0.823 1.635,0.979 0.156,0.156 10 false A 1.167,0.823 1.323,0.979 0.156,0.156 10 false A 2.563,0.615 2.719,0.771 0.156,0.156 10 false a 2.344,0.313 2.698,0.469 0.354,0.156 10 false A-A

Install the back window glass adhesive dam to the back window corner glass LH as shown in the illustration.

Standard:
Area Specified Condition
a 4.7 mm (0.185 in.)


Text in Illustration
*a Back Side
*b Ceramic Notch


Hide 64814A 4.INSTALL BACK WINDOW CORNER GLASS LH

a.

Clean and shape the contact surface of the vehicle body.

i.
B455055E01
0.583,1.177 0.583,1.448 false 0.5,1.479 0.813,1.677 0.313,0.198 10 false *a 3.115,0.375 3.26,0.552 0.146,0.177 10 false a

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

Standard:
Area Specified Condition
a 1.0 mm (0.0394 in.) to 3.0 mm (0.118 in.)



ii.

Clean the contact surface of the vehicle body with non-residue solvent.

Text in Illustration
*a Vehicle Body
V100155

Adhesive



b.

Position the back window corner glass LH.

i.

Using suction cups, place the back window corner glass LH in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.


iii.

Using suction cups, remove the back window corner glass LH.


iv.

Using a brush or sponge, apply body primer to the exposed part of the vehicle body.

NOTICE:
·

Do not apply too much primer.

·

Do not apply primer to the adhesive.

·

When applying the primer, take care of the seams of the panel and spot welds.




v.

Using a brush or sponge, apply glass primer to the contact surface of the glass.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.



B471614E01
0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 1.406,0.198 1.563,0.365 0.156,0.167 10 false A 1.406,0.594 1.563,0.76 0.156,0.167 10 false A 1.063,1.521 1.219,1.688 0.156,0.167 10 false B 1.427,1.521 1.583,1.688 0.156,0.167 10 false B 1.698,3.031 1.854,3.198 0.156,0.167 10 false C 1.75,3.458 1.906,3.625 0.156,0.167 10 false C 2.073,2.417 2.229,2.583 0.156,0.167 10 false D 2.469,2.417 2.625,2.583 0.156,0.167 10 false D 3.865,0.292 4.177,0.458 0.313,0.167 10 false A-A 5.604,0.292 5.917,0.458 0.313,0.167 10 false B-B 3.885,2.073 4.198,2.24 0.313,0.167 10 false C-C 5.583,2.063 5.896,2.229 0.313,0.167 10 false D-D 4.573,0.531 4.708,0.698 0.135,0.167 10 false a 4.854,0.781 4.99,0.948 0.135,0.167 10 false b 6.188,0.667 6.323,0.833 0.135,0.167 10 false c 4.667,2.25 4.802,2.417 0.135,0.167 10 false d 4.958,2.51 5.094,2.677 0.135,0.167 10 false b 6.198,2.281 6.333,2.448 0.135,0.167 10 false e 6.625,2.552 6.76,2.719 0.135,0.167 10 false f

Standard:
Area Specified Condition
a 14.0 mm (0.551 in.)
b 6.0 mm (0.236 in.)
c 22.6 mm (0.890 in.)
d 13.5 mm (0.531 in.)
e 22.0 mm (0.866 in.)
f 7.0 mm (0.276 in.)


Text in Illustration
*a Back Side - -
V100155

Glass Primer Application Area - -



c.

Apply adhesive to the back window corner glass LH.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or Equivalent



d.
B214800E33
2.49,0.583 2.958,0.406 true 1.292,1.427 1.563,1.646 0.271,0.219 10 false a 3,0.292 3.25,0.552 0.25,0.26 10 false *1 0.583,0.625 0.833,0.865 0.25,0.24 10 false a 1.115,0.906 1.427,1.135 0.313,0.229 10 false b 0.76,1.021 0.958,1.229 0.198,0.208 10 false b

Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)


Text in Illustration
*1 Sealer Gun

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.



e.

Load the sealer gun with the cartridge.


f.

Apply adhesive to the glass as shown in the illustration.

NOTICE:

Allow the primer to dry for 3 minutes or more.


B471615E01
4.74,1.49 4.594,1.25 true 6.458,1.448 6.313,1.208 true 4.667,3.344 4.521,3.104 true 6.26,3.094 6.292,3.344 6.292,3.344 6.115,3.094 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 1.396,0.198 1.552,0.354 0.156,0.156 10 false A 1.396,0.583 1.552,0.74 0.156,0.156 10 false A 1.052,1.521 1.208,1.677 0.156,0.156 10 false B 1.448,1.521 1.604,1.677 0.156,0.156 10 false B 1.677,3.031 1.833,3.188 0.156,0.156 10 false C 1.75,3.448 1.906,3.604 0.156,0.156 10 false C 2.073,2.427 2.229,2.583 0.156,0.156 10 false D 2.458,2.417 2.615,2.573 0.156,0.156 10 false D 3.885,0.292 4.208,0.448 0.323,0.156 10 false A-A 5.573,0.292 5.896,0.448 0.323,0.156 10 false B-B 3.875,2.073 4.198,2.229 0.323,0.156 10 false C-C 5.594,2.073 5.917,2.229 0.323,0.156 10 false D-D 4.688,0.646 4.844,0.802 0.156,0.156 10 false a 6.083,0.604 6.24,0.76 0.156,0.156 10 false b 4.604,2.5 4.76,2.656 0.156,0.156 10 false a 6.146,2.302 6.302,2.458 0.156,0.156 10 false c 6.365,2.615 6.521,2.771 0.156,0.156 10 false d 4.729,1.5 5.042,1.698 0.313,0.198 10 false *b 6.448,1.49 6.76,1.688 0.313,0.198 10 false *b 4.677,3.344 4.927,3.5 0.25,0.156 10 false *b 6.302,3.354 6.552,3.51 0.25,0.156 10 false *b

Standard:
Area Specified Condition
a 13.0 mm (0.512 in.)
b 15.6 mm (0.614 in.)
c 8.0 mm (0.315 in.)
d 14.0 mm (0.551 in.)


Text in Illustration
*a Back Side *b Adhesive Center
V100155

Adhesive - -


g.

Install the back window corner glass LH to the vehicle body.


h.
B471607

Using suction cups, attach the 2 back window glass clips LH and install the back window corner glass LH.


i.

Press it in gently along the rim.

NOTICE:
·

Check that the 2 back window glass clips LH are attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.



HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



j.

Using a scraper, remove any excess or protruding adhesive.

NOTICE:

Apply adhesive to the glass rim.



Hide 5.INSPECT FOR LEAKS AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 63940 6.INSTALL NO. 4 INNER COOLER DUCT LH (for Long Body)

Hide 65936 7.INSTALL NO. 1 CURTAIN RAIL (w/ Curtain)

Hide 63316A 8.INSTALL NO. 6 ROOF HEADLINING

Hide 62512R 9.INSTALL REAR BODY REAR INSIDE TRIM LH

Hide 62228 10.INSTALL LOWER QUARTER PILLAR COVER LH

Hide 62472D 11.INSTALL REAR UPPER PILLAR GARNISH LH

Hide 62471D 12.INSTALL REAR UPPER PILLAR GARNISH RH

Hide 62488A 13.INSTALL INNER ROOF SIDE GARNISH COVER LH

Hide 62487A 14.INSTALL INNER ROOF SIDE GARNISH COVER RH

Hide 63349A 15.INSTALL REAR ROOF HEADLINING GARNISH

Hide 66301D 16.INSTALL ROPE HOOK SUB-ASSEMBLY (w/ Rope Hook)

Hide 58614A 17.INSTALL NO. 4 MAT SET PLATE

Hide 63324 18.INSTALL NO. 4 ROOF BOARD

Hide 63372F 19.INSTALL NO. 3 ROOF BOARD SET MOULDING

Hide 63372A 20.INSTALL NO. 2 ROOF BOARD SET MOULDING

Hide 21.INSTALL ROOM RACK (w/ Room Rack)

Hide 45619K 22.INSTALL KNUCKLE STOPPER COVER (w/ Room Rack)

Hide 23.INSTALL REAR SEAT ASSEMBLY (for Rear End)