Home › Vehicle Exterior › WINDOW / GLASS › REAR SIDE WINDOW GLASS REAR RH
RM2850E _59 Vehicle Exterior _073195 WINDOW / GLASS _0356214 REAR SIDE WINDOW GLASS REAR RH A

WINDOW / GLASS  REAR SIDE WINDOW GLASS REAR RH  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.



PROCEDURE

Hide 62730A 1.CLEAN REAR SIDE WINDOW ASSEMBLY RH

a.
E268586

Clean the outer edge of the rear side window assembly RH with non-residue solvent.

NOTICE:
·

Do not touch the rear side window assembly RH surface after cleaning it.

·

Do not damage the glass.

·

Even if using a new rear side window assembly RH, clean the rear side window assembly RH with non-residue solvent.




Hide 62763J 2.INSTALL UPPER QUARTER WINDOW GLASS RETAINER

a.

Using non-residue solvent, clean the upper quarter window glass retainer installation surface of the rear side window assembly RH.


b.

Install the primer to the upper quarter window glass retainer installation surface of the rear side window assembly RH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new upper quarter window glass retainer.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.
B477296E01
0.771,1.406 1.458,1.156 true 2.781,1.448 2.052,1.167 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 0.573,1.354 0.885,1.552 0.313,0.198 10 false *b 2.833,1.375 3.146,1.573 0.313,0.198 10 false *b

Install the 2 upper quarter window glass retainers to the rear side window assembly RH as shown in the illustration.

Text in Illustration
*a Back Side
*b Ceramic Notch


Hide 62785D 3.INSTALL QUARTER WINDOW GLASS SPACER

a.

Using non-residue solvent, clean the quarter window glass spacer installation surface of the rear side window assembly RH.


b.

Install the primer to the quarter window glass spacer installation surface of the rear side window assembly RH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new quarter window glass spacer.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the 4 quarter window glass spacers to the rear side window assembly RH as shown in the illustration.

B477297E01
2.104,0.25 2.01,0.135 2.01,0.135 1.854,0.135 true 5.24,0.24 5.146,0.125 5.146,0.125 4.99,0.125 true 1.688,0.823 2.01,0.698 true 2.385,0.896 2.198,0.698 true 4.938,0.948 5.135,0.698 true 5.531,0.948 5.333,0.708 true 2.115,2 2.021,1.885 2.021,1.885 1.865,1.885 true 5.24,1.99 5.146,1.875 5.146,1.875 4.99,1.875 true 1.938,2.698 2.094,2.698 2.094,2.698 2.094,2.583 true 5.135,2.708 5.292,2.708 5.292,2.708 5.292,2.594 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.656,0.073 1.875,0.25 0.219,0.177 10 false *b 1.458,0.76 1.677,0.938 0.219,0.177 10 false *b 2.396,0.906 2.615,1.083 0.219,0.177 10 false *b 4.781,0.052 5,0.229 0.219,0.177 10 false *b 4.865,0.958 5.083,1.135 0.219,0.177 10 false *b 5.531,0.948 5.75,1.125 0.219,0.177 10 false *b 1.625,1.802 1.875,1.948 0.25,0.146 10 false *b 1.719,2.594 1.917,2.76 0.198,0.167 10 false *b 4.792,1.781 4.99,1.948 0.198,0.167 10 false *b 4.938,2.615 5.135,2.781 0.198,0.167 10 false *b

Text in Illustration
*a Back Side *b Ceramic Notch

HINT:

The 2 spacers to be installed at the under of the glass have different shapes.



Hide 62730A 4.INSTALL REAR SIDE WINDOW ASSEMBLY RH

a.

Clean and shape the contact surface of the vehicle body.

i.
B455055E01
0.583,1.177 0.583,1.448 false 0.5,1.479 0.813,1.677 0.313,0.198 10 false *a 3.115,0.375 3.26,0.552 0.146,0.177 10 false a

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

Standard:
Area Specified Condition
a 1.0 mm (0.0394 in.) to 3.0 mm (0.118 in.)



ii.

Clean the contact surface of the vehicle body with non-residue solvent.

Text in Illustration
*a Vehicle Body
V100155

Adhesive



b.

Position the rear side window assembly RH.

i.

Using suction cups, place the rear side window assembly RH in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.


iii.

Using suction cups, remove the rear side window assembly RH.


iv.

Using a brush or sponge, apply body primer to the exposed part of the vehicle body.

NOTICE:
·

Do not apply too much primer.

·

Do not apply primer to the adhesive.

·

When applying the primer, take care of the seams of the panel and spot welds.




v.

Using a brush or sponge, apply glass primer to the contact surface of the glass.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.



B477298E01
0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 2.208,0.177 2.365,0.375 0.156,0.198 10 false A 2.208,0.615 2.365,0.813 0.156,0.198 10 false A 0.99,1.646 1.146,1.844 0.156,0.198 10 false A 0.635,1.646 0.792,1.844 0.156,0.198 10 true A 2.219,3.042 2.375,3.24 0.156,0.198 10 false A 2.229,3.406 2.385,3.604 0.156,0.198 10 true A 2.76,2.615 2.917,2.813 0.156,0.198 10 false B 3.135,2.604 3.292,2.802 0.156,0.198 10 true B 3.771,1.115 4.167,1.281 0.396,0.167 10 false A-A 5.49,1.125 5.885,1.292 0.396,0.167 10 false B-B

Text in Illustration
*a Back Side - -
V100155

Glass Primer Application Area - -



c.

Apply adhesive to the rear side window assembly RH.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or Equivalent



d.
B214800E33
2.49,0.583 2.958,0.406 true 1.292,1.427 1.563,1.646 0.271,0.219 10 false a 3,0.292 3.25,0.552 0.25,0.26 10 false *1 0.583,0.625 0.833,0.865 0.25,0.24 10 false a 1.115,0.906 1.427,1.135 0.313,0.229 10 false b 0.76,1.021 0.958,1.229 0.198,0.208 10 false b

Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)


Text in Illustration
*1 Sealer Gun

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.



e.

Load the sealer gun with the cartridge.


f.

Apply adhesive to the glass as shown in the illustration.

NOTICE:

Allow the primer to dry for 3 minutes or more.


B477299E01
0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 2.198,0.177 2.354,0.375 0.156,0.198 10 false A 2.198,0.604 2.354,0.802 0.156,0.198 10 false A 1,1.635 1.156,1.833 0.156,0.198 10 false A 0.635,1.635 0.792,1.833 0.156,0.198 10 true A 2.177,3.042 2.333,3.24 0.156,0.198 10 false A 2.177,3.406 2.333,3.604 0.156,0.198 10 true A 2.74,2.646 2.896,2.844 0.156,0.198 10 false B 3.125,2.635 3.281,2.833 0.156,0.198 10 true B 3.792,1.104 4.156,1.281 0.365,0.177 10 false A-A 5.49,1.104 5.854,1.281 0.365,0.177 10 false B-B

Text in Illustration
*a Back Side *b Adhesive Center
V100155

Adhesive - -


g.

Install the rear side window assembly RH to the vehicle body.


h.

Using suction cups, attach the 4 quarter window glass spacers and install the rear side window assembly RH.


i.

Press it in gently along the rim.

NOTICE:
·

Check that the 4 quarter window glass spacers are attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.



HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



j.

Using a scraper, remove any excess or protruding adhesive.

NOTICE:

Apply adhesive to the glass rim.



Hide 5.INSPECT FOR LEAKS AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 63316A 7.INSTALL NO. 6 ROOF HEADLINING

Hide 62511R 8.INSTALL REAR BODY REAR INSIDE TRIM RH

Hide 62227 9.INSTALL QUARTER PILLAR COVER RH

Hide 62471D 10.INSTALL REAR UPPER PILLAR GARNISH RH

Hide 62472D 11.INSTALL REAR UPPER PILLAR GARNISH LH

Hide 64735A 12.INSTALL CENTER BACK RAIL INNER GARNISH (for Lift Up Type)

Hide 62487A 13.INSTALL INNER ROOF SIDE GARNISH COVER RH (for Double Swing Out Type)

Hide 62488A 14.INSTALL INNER ROOF SIDE GARNISH COVER LH (for Double Swing Out Type)

Hide 63349A 15.INSTALL REAR ROOF HEADLINING GARNISH (for Double Swing Out Type)

Hide 65905B 16.INSTALL WINDOW CURTAIN RAIL SUB-ASSEMBLY (for Lift Up Type, w/ Curtain)

Hide 66301D 17.INSTALL ROPE HOOK SUB-ASSEMBLY (for Double Swing Out Type)

Hide 58614A 18.INSTALL NO. 4 MAT SET PLATE

Hide 63930 19.INSTALL NO. 4 INNER COOLER DUCT RH (for Long Body)

Hide 65936 20.INSTALL NO. 1 CURTAIN RAIL (w/ Curtain)

Hide 63324 21.INSTALL NO. 4 ROOF BOARD

Hide 63372F 22.INSTALL NO. 3 ROOF BOARD SET MOULDING

Hide 63372A 23.INSTALL NO. 2 ROOF BOARD SET MOULDING

Hide 24.INSTALL ROOM RACK ASSEMBLY (w/ Room Rack)

Hide 25.INSTALL REAR SEAT ASSEMBLY (for Rear End)