Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for RHD vehicles.
1.INSTALL REAR SIDE FRONT WINDOW GLASS LH
Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 1.0 to 3.0 mm (0.0394 to 0.118 in.) |
Clean the contact surface of the vehicle body with non-residue solvent.
| *a | Vehicle Body |
|
Adhesive |
Using non-residue solvent, clean the rear side front window glass LH installation surface of the vehicle body.
Install the body primer to the rear side front window glass LH installation surface of the vehicle body.
Do not apply too much primer.
Do not apply primer to the adhesive.
When applying the primer, take care of the seams of the panel and spot welds.
Install the suction cups to the rear side front window glass LH.
for Slide Type:
Using a brush or sponge, apply primer to the contact surface of the rear side front window glass LH.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | - | - |
|
Primer Application Area | - | - |
Apply adhesive to the rear side front window glass LH.
Toyota Genuine Windshield Glass Adhesive or Equivalent
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| *1 | Sealer Gun |
Apply adhesive to the rear side front window glass LH as shown in the illustration.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | *b | R End |
|
Adhesive | - | - |
| Area | Specified Condition |
|---|---|
| a | 9.0 mm (0.354 in.) |
| b | 13.0 mm (0.512 in.) |
| c | 5.0 mm (0.197 in.) |
Fixed Type:
Using a brush or sponge, apply glass primer to the contact surface of the rear side front window glass LH.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | - | - |
|
Glass Primer Application Area | - | - |
Apply adhesive to the rear side front window glass LH.
Toyota Genuine Windshield Glass Adhesive or Equivalent
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| *1 | Sealer Gun |
Apply adhesive to the rear side front window glass LH as shown in the illustration.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | *b | Adhesive Center |
|
Adhesive | - | - |
Install the rear side front window glass LH to the vehicle body.
Using suction cups, attach the 4 side window glass spacers and install the rear side front window glass LH.
Press it in gently along the rim.
Check that the spacers, retainers are attached to the vehicle body correctly.
Check that the vehicle body and glass have a small gap between them.
Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Apply adhesive to the glass rim.
2.INSPECT FOR LEAKS AND REPAIR
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
63316A
3.INSTALL NO. 6 ROOF HEADLINING
62452B
4.INSTALL NO. 3 ROOF SIDE RAIL GARNISH LH (w/o Rear Air Duct)
62452C
5.INSTALL REAR ROOF SIDE RAIL GARNISH LH (w/o Rear Air Duct)
62451E
6.INSTALL REAR ROOF SIDE RAIL GARNISH (w/o Rear Air Duct)
63372G
7.INSTALL NO. 4 ROOF BOARD SET MOULDING (w/o Rear Air Duct)
63378C
8.INSTALL NO. 3 ROOF HEADLINING MOULDING (w/o Rear Air Duct)
63377C
9.INSTALL NO. 2 ROOF HEADLINING MOULDING (w/o Rear Air Duct)
63372A
10.INSTALL NO. 2 ROOF BOARD SET MOULDING (w/o Rear Air Duct)
11.INSTALL SIDE PANEL
for RHD:
Click hereVehicle Interior>INTERIOR>SIDE PANEL (for RHD)>INSTALLATION
for LHD:
Click hereVehicle Interior>INTERIOR>SIDE PANEL (for LHD)>INSTALLATION
62512R
12.INSTALL REAR BODY REAR INSIDE TRIM LH
62228
13.INSTALL LOWER QUARTER PILLAR COVER LH
62472D
14.INSTALL REAR UPPER PILLAR GARNISH LH
62471D
15.INSTALL REAR UPPER PILLAR GARNISH RH
62487A
16.INSTALL INNER ROOF SIDE GARNISH COVER RH (for Double Swing Out Type)
62488A
17.INSTALL INNER ROOF SIDE GARNISH COVER LH (for Double Swing Out Type)
63349A
18.INSTALL REAR ROOF HEADLINING GARNISH (for Double Swing Out Type)
65905B
19.INSTALL WINDOW CURTAIN RAIL SUB-ASSEMBLY (for Lift Up Type, w/ Curtain)
64735A
20.INSTALL CENTER BACK RAIL INNER GARNISH (for Lift Up Type)
66301D
21.INSTALL ROPE HOOK SUB-ASSEMBLY (w/ Rope Hook)
58614A
22.INSTALL NO. 4 MAT SET PLATE
63940
23.INSTALL 4 INNER COOLER DUCT LH (for Long Body, w/ Rear Air Duct)
63917A
24.INSTALL NO. 3 INNER COOLER DUCT LH (w/ Rear Air Duct)
63926
25.INSTALL NO. 2 INNER COOLER DUCT LH (w/ Rear Air Duct)
63323
26.INSTALL NO. 3 ROOF BOARD (w/ Rear Air Duct)
65936
27.INSTALL NO. 1 CURTAIN RAIL (w/ Curtain)
65937
28.INSTALL CURTAIN RAIL NO.2 (w/ Curtain)
63324
29.INSTALL NO. 4 ROOF BOARD (for Long Body, w/ Rear Air Duct)
63372F
30.INSTALL NO. 3 ROOF BOARD SET MOULDING (w/ Rear Air Duct)
63372A
31.INSTALL NO. 2 ROOF BOARD SET MOULDING (w/ Rear Air Duct)
32.INSTALL ROOM RACK ASSEMBLY (w/ Room Rack)
45619K
33.INSTALL KNUCKLE STOPPER COVER (w/ Room Rack)
34.INSTALL REAR SEAT ASSEMBLY (for Rear End)
for Tumble Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Tumble Type 4-Passenger Seat)>INSTALLATION
for Fixed Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fixed Type 4-Passenger Seat)>INSTALLATION