Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1403 and C1404 (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>C1403).

DTC No. DTC Detection Condition Trouble Area
C1407
C1408
Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor RH/LH

·

Wire harness or connector

·

Rear skid control sensor wire

·

Skid control ECU (Brake actuator assembly)



HINT:
·

DTC C1407 is for the rear speed sensor RH.

·

DTC C1408 is for the rear speed sensor LH.



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CHECK FOR INTERMITTENT PROBLEMS).

OK:

Normal (There are no momentary interruptions.)


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

4.INSPECT REAR SKID CONTROL SENSOR WIRE
2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


g.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.INSPECT REAR SKID CONTROL SENSOR WIRE
3.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.



Result:
Result Proceed to
DTCs C1407 and C1408 are not output A
DTCs C1407 and/or C1408 are output B



A

B

4.INSPECT REAR SKID CONTROL SENSOR WIRE
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.



d.

Measure the resistance according to the value(s) in the table below.

C371275E02
1.031,0.625 1.458,0.833 0.427,0.208 3.396,0.625 3.823,0.833 0.427,0.208 5.719,0.635 6.146,0.844 0.427,0.208 1.521,1.469 2,0.917 true 6.177,1.51 6.615,0.948 true 1.042,1.469 0.469,0.875 true 5.677,1.5 5.177,0.917 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *1 1.208,2.25 1.521,2.448 0.313,0.198 10 false *a 3.552,2.302 3.865,2.5 0.313,0.198 10 false *b 0.323,0.708 0.677,0.906 0.354,0.198 10 false RL- 5.885,2.292 6.198,2.49 0.313,0.198 10 false *a 1.167,0.635 1.521,0.833 0.354,0.198 10 false p3 1.51,0.552 1.865,0.75 0.354,0.198 10 false *B 1.969,0.698 2.365,0.896 0.396,0.198 10 false RL+ 3.479,0.635 3.844,0.833 0.365,0.198 10 false Pp1 5.052,0.75 5.417,0.948 0.365,0.198 10 false RR- 5.854,0.646 6.219,0.844 0.365,0.198 10 false p4 6.208,0.552 6.573,0.75 0.365,0.198 10 false *A 6.563,0.76 6.969,0.958 0.406,0.198 10 false RR+

Text in Illustration
*A for RH *B for LH
*1 Rear Skid Control Sensor Wire - -
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
Pp1-5 - p4-1 (RR+) Always Below 1 Ω
Pp1-1 - p4-3 (RR-) Always Below 1 Ω
Pp1-5 - Pp1-8 Always 10 kΩ or higher
Pp1-5 - Pp1-4 Always 10 kΩ or higher
Pp1-5 - Pp1-1 Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
Pp1-8 - p3-1 (RL+) Always Below 1 Ω
Pp1-4 - p3-3 (RL-) Always Below 1 Ω
Pp1-8 - Pp1-4 Always 10 kΩ or higher
Pp1-8 - Pp1-5 Always 10 kΩ or higher
Pp1-8 - Pp1-1 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

b.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the p4 and p3 rear speed sensor connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A71-16 (RR+) - p4-1 (RR+) Always Below 1 Ω
A71-16 (RR+) or p4-1 (RR+) - Body ground Always 10 kΩ or higher
A71-15 (RR-) - p4-3 (RR-) Always Below 1 Ω
A71-15 (RR-) or p4-3 (RR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A71-29 (RL+) - p3-1 (RL+) Always Below 1 Ω
A71-29 (RL+) or p3-1 (RL+) - Body ground Always 10 kΩ or higher
A71-28 (RL-) - p3-3 (RL-) Always Below 1 Ω
A71-28 (RL-) or p3-3 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.
C369076E02
1.5,0.188 1.927,0.375 0.427,0.188 1.5,0.448 1.927,0.635 0.427,0.188 2.01,1.219 2.5,0.771 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 1.635,0.188 1.948,0.385 0.313,0.198 10 false p4 1.635,0.448 1.948,0.646 0.313,0.198 10 false p3 1.979,0.198 2.292,0.396 0.313,0.198 10 false *A 1.99,0.458 2.302,0.656 0.313,0.198 10 false *B 2.552,0.688 3.177,0.906 0.625,0.219 10 false RR+ *A 2.563,0.885 3.188,1.104 0.625,0.219 10 false RL- *B

Reconnect the A71 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH:
Tester Connection Condition Specified Condition
p4-1 (RR+) - Body ground Ignition switch ON 8 to 14 V

for LH:
Tester Connection Condition Specified Condition
p3-1 (RL+) - Body ground Ignition switch ON 8 to 14 V


Text in Illustration
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Result:
Proceed to
OK
NG



OK

NG