Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C1430  Brake Pedal Load Sensing Switch OFF Stuck Malfunction  C1431  Brake Pedal Load Sensing Switch ON Stuck Malfunction  


DESCRIPTION

The brake pedal load sensing switch (brake with switch pedal sub-assembly) is turned on when the brake pedal is depressed with force exceeding a predetermined level.

The skid control ECU (brake actuator assembly) detects if the brake pedal is depressed or not via this circuit.

DTC No. DTC Detection Condition Trouble Area
C1430 Any of the following is detected:
1.

With the stop light switch ON, the brake pedal load sensing switch OFF, and the master cylinder pressure 6 MPa or more, the deceleration is 0.4 G or more for 1 second or more.

2.

With the stop light switch ON, the brake pedal load sensing switch OFF, and the master cylinder pressure 6 MPa or more, the vehicle speed is 0 km/h (0 mph) for 5 seconds or more.


·

Brake pedal load sensing switch (Brake with switch pedal sub-assembly)

·

Brake pedal load sensing switch circuit

·

Skid control ECU (Brake actuator assembly)


C1431 Any of the following is detected:
1.

The brake pedal load sensing switch is ON and the stop light switch is OFF for 10 seconds or more.

2.

The condition that the brake pedal load sensing switch remains ON while the vehicle speed increases from 0 km/h (0 mph) to 30 km/h (18 mph) occurs 5 times in succession.


·

Brake pedal load sensing switch (Brake with switch pedal sub-assembly)

·

Brake pedal load sensing switch circuit

·

Skid control ECU (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).


HINT:

When DTC C1425 and/or C1426 is output together with DTC C1430 and/or C1431, inspect and repair the trouble areas indicated by DTC C1425 and/or C1426 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>C1425, or Click HereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>C1426).


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SW/BRAKE PEDAL LOAD SENSING SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch (brake with switch pedal sub-assembly) / ON or OFF ON: Brake pedal depressed beyond the specified point
OFF: Brake pedal not depressed beyond the specified point
-


f.

Check that the stop light switch display and brake pedal load sensing switch display observed on the GTS change according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



g.

Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn ON.

OK:

First the stop light switch should turn ON, and then the brake pedal load sensing switch should turn ON.



Result:
Result Proceed to
OK A
NG (Turning on of the brake pedal load sensing switch is not confirmed) B
NG (The brake pedal load sensing switch turns on first) C



A

2.RECONFIRM DTC

B

3.INSPECT BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

C

5.ADJUST BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform the road test.



Result:
Result Proceed to
DTCs C1430 and C1431 are not output A
DTCs C1430 and/or C1431 are output B



A

B

3.INSPECT BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY
a.

Inspect the brake pedal load sensing switch (brake pedal support assembly) (Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (w/ Brake pedal Load Sensing Switch)>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY)

NG

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.ADJUST BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Adjust the brake pedal height and stop light switch assembly installation (Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (w/ Brake pedal Load Sensing Switch)>ADJUSTMENT).


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform the road test.



Result:
Result Proceed to
DTCs C1430 and C1431 are not output A
DTCs C1430 and/or C1431 are output B



A

END

B

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY