Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM C

N04C-VL ENGINE CONTROL  ECD SYSTEM  P0088  Fuel Rail / System Pressure - Too High  P0627  Fuel Pump Control Circuit / Open  P1229  Fuel Pump System  


DESCRIPTION

The injection or supply pump assembly is a single-type pump and has a circuit for fuel suction that achieves high pressure force feed and reduction of driving torque, and for force feed process. The ECM controls the suction control valve, which operates fuel suction by means of the plunger.

When the internal fuel pressure of the common rail assembly exceeds the target pressure, the fuel pressure limiter on the common rail assembly starts operating to control the internal fuel pressure.

DTC No. DTC Detection Condition Trouble Area
P0088 Conditions (a) and (b) are met 150 times or more (1 trip detection logic):
(a) Ignition switch ON.
(b) Internal fuel pressure of the common rail: 250 MPa (2549 kgf/cm2, 36259 psi) or more.
·

Suction control valve

·

Open or short in suction control valve circuit

·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

Fuel pressure limiter (common rail assembly)

·

ECM


P0627 Open or short in suction control valve circuit for more than 0.5 seconds (1 trip detection logic).
·

Suction control valve

·

Open or short in suction control valve circuit

·

ECM


P1229 Fuel over-feed (1 trip detection logic):
The actual fuel pressure exceeds the target fuel pressure by 40000 kPa or higher for 10 seconds.
·

Suction control valve

·

Open or short in suction control valve circuit

·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

Fuel pressure limiter (common rail assembly)

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the suction control valve, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:
·

If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P0087, P0180, P0182, P0183, P0190, P0191, P0192, P0193, P0201, P0202, P0203, P0204 or P062D is not output A
DTC P0087, P0180, P0182, P0183, P0190, P0191, P0192, P0193, P0201, P0202, P0203, P0204 or P062D is output B




A

2.INSPECT SUCTION CONTROL VALVE

B

2.INSPECT SUCTION CONTROL VALVE
a.

Inspect the suction control valve (Click hereEngine / Hybrid System>N04C-VL (FUEL)>FUEL SUPPLY PUMP>INSPECTION).


Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P0088 and/or P1229 are output A
DTC P0627 is output B



A

4.READ VALUE USING GTS (TARGET PUMP SCV CURRENT)

B

8.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
4.READ VALUE USING GTS (TARGET PUMP SCV CURRENT)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current.


e.

Read the value.

Standard:
GTS Display Condition Specified Condition
Target Pump SCV Current Idling 1350 to 2200 mA



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (FUEL PRESS, TARGET COMMON RAIL PRESSURE)

NG

11.INSPECT FUEL INJECTION SYSTEM
5.READ VALUE USING GTS (FUEL PRESS, TARGET COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.


e.

Read the Value.

Standard:
GTS Display Condition Specified Condition
Fuel Press Idling 25000 to 35000 kPa
3000 rpm without load 100000 to 110000 kPa
Target Common Rail Pressure Idling Deviation from Fuel Press within 5000 kPa
3000 rpm without load Deviation from Fuel Press within 5000 kPa



Result:
Result Proceed to
NG A
OK B



A

6.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

B

8.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
6.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B105-16 (PCR1) - B93-2 (PCR1) Always Below 1 Ω
B104-13 (VC) - B93-1 (VC1) Always Below 1 Ω
B104-14 (E2) - B93-3 (E1) Always Below 1 Ω
B105-2 (PCR2) - B93-5 (PCR2) Always Below 1 Ω
B105-13 (VC2) - B93-6 (VC2) Always Below 1 Ω
B105-14 (E21) - B93-4 (E2) Always Below 1 Ω
B105-16 (PCR1) or B93-2 (PCR1) - Body ground Always 10 kΩ or higher
B104-13 (VC) or B93-1 (VC1) - Body ground Always 10 kΩ or higher
B105-2 (PCR2) or B93-5 (PCR2) - Body ground Always 10 kΩ or higher
B105-13 (VC2) or B93-6 (VC2) - Body ground Always 10 kΩ or higher
B104-14 (E2) or B93-3 (E1) - Other terminals Always 10 kΩ or higher
B105-14 (E21) or B93-4 (E2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (FUEL PRESS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PRESSURE SENSOR (COMMON RAIL ASSEMBLY) - ECM)

7.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Wiggle the fuel pressure sensor (common rail assembly) connector and check that the fuel pressure reading does not change.

OK:

The fuel pressure reading does not change.



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

NG

REPLACE FUEL PRESSURE SENSOR (COMMON RAIL ASSEMBLY)

8.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B52-1 (SCV+) - B103-23 (PCV+) Always Below 1 Ω
B52-2 (SCV-) - B103-12 (PCV-) Always Below 1 Ω
B52-1 (SCV+) or B103-23 (PCV+) - Body ground Always 10 kΩ or higher
B52-2 (SCV-) or B103-12 (PCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK ECM TERMINAL VOLTAGE (PCV+ AND PCV- TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SUCTION CONTROL VALVE - ECM)

9.CHECK ECM TERMINAL VOLTAGE (PCV+ AND PCV- TERMINAL)
a.
A256048E06
2.302,0.188 2.792,0.448 0.49,0.26 2.802,0.188 3.292,0.448 0.49,0.26 3.25,0.729 3.094,1.667 true 2.74,0.958 2.417,1.677 true 2.74,0.844 1.552,1.667 true 2.385,0.24 2.771,0.417 0.385,0.177 10 false B103 2.885,0.24 3.302,0.427 0.417,0.188 10 false B102 2.948,1.688 3.385,1.885 0.438,0.198 10 false 1 (E1) 2.083,1.688 2.833,1.865 0.75,0.177 10 false 23 (PCV+) 0.115,3.927 0.531,4.094 0.417,0.167 10 false PCV- 1.26,1.688 1.938,1.854 0.677,0.167 10 false 12 (PCV-) 0.083,0.052 0.281,0.219 0.198,0.167 10 false *a 0.094,3.594 0.51,3.76 0.417,0.167 10 false PCV+ 1.292,4.323 2.177,4.563 0.885,0.24 10 false 5 ms./DIV. 2.635,3.448 3.427,3.667 0.792,0.219 10 false 10 V/DIV. 2.656,4.094 3.427,4.271 0.771,0.177 10 false 1 V/DIV. 2.844,3.625 3.219,3.813 0.375,0.188 10 false GND 2.854,3.948 3.229,4.135 0.375,0.188 10 false GND

While cranking or idling the engine, check the waveform of the ECM connector using an oscilloscope.

Standard:
Tester Connection Condition Tool Setting Specified Condition
B103-23 (PCV+) - B102-1 (E1) Idling or cranking with warm engine 10 V/DIV., 5 ms./DIV. Correct waveform appears as shown
B103-12 (PCV-) - B102-1 (E1) Idling or cranking with warm engine 1 V/DIV., 5 ms./DIV. Correct waveform appears as shown


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

10.CHECK WHETHER DTC OUTPUT RECURS

NG

10.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.


Result:
Result Proceed to
DTC P0088, P0627 or P1229 is output A
DTC is not output B



A

11.INSPECT FUEL INJECTION SYSTEM

B

11.INSPECT FUEL INJECTION SYSTEM
a.

Inspect the fuel injection system circuit (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>Fuel Injection System).


b.

Check whether the malfunction has been repaired successfully.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG