The ECM controls the fuel injection compensation volume when the engine is idling.
If excessive deposits are present in an injector assembly, it may lower the fuel injection volume, resulting in an engine that stalls or has an unstable idle. Therefore, the ECM increases the fuel injection compensation volume to ensure the fuel injection volume necessary for idling.
The ECM stores this DTC if the fuel injection compensation volume exceeds the specified value.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0263
P0266 P0269 P0272 |
Conditions (a) and (b) are met more than 200 times with engine speed 500 to 1000 rpm (1 trip detection logic):
(a) Engine coolant temperature: 60°C (140°F) or more. (b) Difference of compensation value between cylinders: 15 mm3/st or more. |
·
Open or short in injector driver circuit ·
Injector assembly ·
Injector driver ·
ECM ·
Compression |
These DTCs indicate a malfunction related to the primary circuit.
If DTC P0263 is displayed, check the No. 1 injector circuit.
If DTC P0266 is displayed, check the No. 2 injector circuit.
If DTC P0269 is displayed, check the No. 3 injector circuit.
If DTC P0272 is displayed, check the No. 4 injector circuit.
Refer to DTC P0201 (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>P0201).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
After replacing the injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0263, P0266, P0269 and/or P0272 are output | A |
| DTC P0263, P0266, P0269 and/or P0272 and other DTCs are output | B |
If any DTCs other than P0263, P0266, P0269 and/or P0272 are output, troubleshoot those DTCs first.
A
B
Change the installed injector assembly to a known good injector assembly.
Input the injector compensation code (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| Same DTCs are output (same as DTCs that were cleared) | A |
| Other DTCs are output | B |
If a DTC for a different cylinder is stored when the injector assembly has been switched with a known good one from a different cylinder, the injector assembly may be malfunctioning.
If no DTC is stored after the injector assembly has been replaced, the injector assembly may be malfunctioning.
If the same DTC is stored again even after replacing the injector assembly with a known good injector assembly, the ECM, injector driver, engine or wire harness may be malfunctioning.
A
B
Disconnect the injector driver connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B98-5 (INJ1) - B98-1 (COM1) | 20°C (68°F) | 0.85 to 1.05 Ω |
| B96-4 (INJ2) - B98-2 (COM2) | 20°C (68°F) | 0.85 to 1.05 Ω |
| B96-2 (INJ3) - B98-2 (COM2) | 20°C (68°F) | 0.85 to 1.05 Ω |
| B98-4 (INJ4) - B98-1 (COM1) | 20°C (68°F) | 0.85 to 1.05 Ω |
| *a | Front view of wire harness connector
(to Injector Driver) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the injector driver connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B95-6 (#10) - B105-21 (#1) | Always | Below 1 Ω |
| B95-2 (#20) - B105-22 (#2) | Always | Below 1 Ω |
| B95-1 (#30) - B105-23 (#3) | Always | Below 1 Ω |
| B95-3 (#40) - B105-24 (#4) | Always | Below 1 Ω |
| B96-1 (INJF) - B105-20 (INJF) | Always | Below 1 Ω |
| B95-6 (#10) or B105-21 (#1) - Body ground | Always | 10 kΩ or higher |
| B95-2 (#20) or B105-22 (#2) - Body ground | Always | 10 kΩ or higher |
| B95-1 (#30) or B105-23 (#3) - Body ground | Always | 10 kΩ or higher |
| B95-3 (#40) or B105-24 (#4) - Body ground | Always | 10 kΩ or higher |
| B96-1 (INJF) or B105-20 (INJF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
While idling the engine, check the waveform of the ECM connectors using an oscilloscope.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B105-21 (#1) - B102-1 (E1) | Idling with warm engine | Correct waveform appears as shown |
| B105-22 (#2) - B102-1 (E1) | Idling with warm engine | Correct waveform appears as shown |
| B105-23 (#3) - B102-1 (E1) | Idling with warm engine | Correct waveform appears as shown |
| B105-24 (#4) - B102-1 (E1) | Idling with warm engine | Correct waveform appears as shown |
| B105-20 (INJF) - B102-1 (E1) | Idling with warm engine | Correct waveform appears as shown |
| *a | Component with harness connected
(ECM) |
| *b | Signal Waveform |
| Result | Proceed to |
|---|---|
| #1 to #4 and INJF are normal | A |
| #1 to #4 are normal, INJF is abnormal | B |
| #1 to #4 are abnormal, INJF is normal | C |
A
B
C
Measure the cylinder compression pressure of the misfiring cylinder (Click hereEngine / Hybrid System>N04C-VL (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
NG
Inspect the injector assembly (Click hereEngine / Hybrid System>N04C-VL (FUEL)>FUEL INJECTOR>INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the injector assembly of the malfunctioning cylinder.
Check the injector assembly for any deposits.
| Result | Proceed to |
|---|---|
| Deposits | A |
| No deposits | B |
If excessive deposits are present on the head of the injector assembly, a malfunction of something other than the injector assembly has resulted in an increase of the fuel injection compensation volume. First perform the troubleshooting procedure for black smoke.
A
B