Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM J

N04C-VL ENGINE CONTROL  ECD SYSTEM  Black Smoke Emitted  


DESCRIPTION

Refer to DTC P0087 for fuel pressure sensor circuit (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>P0087).

Refer to DTC P0107 for vacuum sensor circuit (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>P0107).

Refer to DTC P0112 for intake air temperature sensor circuit (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>P0112).

Refer to DTC P0115 for water temperature sender gauge circuit (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>P0115

Refer to DTC P0201 for injector circuit (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>P0201).

Refer to DTC P0335 for crankshaft position sensor circuit (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>P0335).

Refer to DTC P2120 for accelerator pedal position sensor circuit (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>P2120).

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not assume the vehicle to be normal when the Data List outputs standard values. There may be concealed factors causing the malfunction.


PROCEDURE

1.CHECK OUTPUT DTC (RELATED TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTCs related to the engine are output B




A

2.READ VALUE USING GTS (INJECTION VOLUME AND INJECTION FEED BACK VAL #1 TO #4)

B

2.READ VALUE USING GTS (INJECTION VOLUME AND INJECTION FEED BACK VAL #1 TO #4)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

Injection Volume

·

Injection Feedback Val #1, #2, #3 and #4


Standard:
GTS Display Condition* Reference Value
Injection Volume Idling (No engine load) 5.0 to 15.0 mm3/st
Injection Feedback Val #1 Idling (No engine load) -7.0 to 7.0 mm3/st
Injection Feedback Val #2 Idling (No engine load) -7.0 to 7.0 mm3/st
Injection Feedback Val #3 Idling (No engine load) -7.0 to 7.0 mm3/st
Injection Feedback Val #4 Idling (No engine load) -7.0 to 7.0 mm3/st


HINT:

*: If no idling conditions are specified, the shift lever should be in the neutral position, and the A/C switch and all accessory switches should be off.



Result:
Proceed to
OK
NG



OK

3.PERFORM ENGINE SPEED ACCELERATION

NG

11.CHECK ECM TERMINAL VOLTAGE (THW TERMINAL)
3.PERFORM ENGINE SPEED ACCELERATION
HINT:

If the exhaust gas contains excessive black smoke, perform the following operations:


a.

Accelerate the engine speed to the maximum speed with no load 20 times.


b.

Check for black smoke in the exhaust gas.

Result:
Result Proceed to
Black smoke remains in the exhaust gas A
Black smoke is not present B


HINT:

Soot deposits in the exhaust system may cause excessive black smoke.




A

4.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

4.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
a.

Check intake system and exhaust system.


Result:
Proceed to
OK
NG



OK

5.INSPECT EXHAUST RETARDER ASSEMBLY

NG

CHECK LOCATIONS WHERE MALFUNCTIONS EXIST

5.INSPECT EXHAUST RETARDER ASSEMBLY
a.

Inspect the exhaust retarder assembly.


Result:
Proceed to
OK
NG



OK

6.CHECK TURBOCHARGER SUB-ASSEMBLY

NG

REPLACE EXHAUST RETARDER ASSEMBLY

6.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check the turbocharger sub-assembly (Click hereEngine / Hybrid System>N04C-VL (INTAKE)>TURBOCHARGER>INSPECTION).


Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY

7.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

Fuel Press

·

Injection Volume

·

Main Injection Period

·

Pilot 2 Injection Period

·

Injection Feedback Val #1, #2, #3 and #4


Standard:
GTS Display Condition* Reference Value
Fuel Press Idling 25000 to 35000 kPa
Injection Volume Idling 5.0 to 15.0 mm3/st
Main Injection Period Idling 600 to 1000 μs
Pilot 2 Injection Period Idling 0 to 600 μs
Injection Feedback Val #1 Idling -7.0 to 7.0 mm3/st
Injection Feedback Val #2 Idling -7.0 to 7.0 mm3/st
Injection Feedback Val #3 Idling -7.0 to 7.0 mm3/st
Injection Feedback Val #4 Idling -7.0 to 7.0 mm3/st


HINT:

*: If no idling conditions are specified, the shift lever should be in the neutral position, and the A/C switch and all accessory switches should be off.



Result:
Result Proceed to
Within reference value A
One of Injection Feedback Val #1 to #4 is not within reference value B
Other result C



A

8.CHECK CYLINDER COMPRESSION PRESSURE

B

C

11.CHECK ECM TERMINAL VOLTAGE (THW TERMINAL)
8.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure (Click hereEngine / Hybrid System>N04C-VL (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

9.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER)
a.

Check the wire harness between the injector assembly and injector driver assembly (IJ terminal).

i.

Disconnect the injector assembly connectors.


ii.

Disconnect the injector driver assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 - B98-5 (INJ1) Always Below 1 Ω
i2-2 - B96-4 (INJ2) Always Below 1 Ω
i3-2 - B96-2 (INJ3) Always Below 1 Ω
i4-2 - B98-4 (INJ4) Always Below 1 Ω
i1-1 - B98-1 (COM1) Always Below 1 Ω
i2-1 - B98-2 (COM2) Always Below 1 Ω
i3-1 - B98-2 (COM2) Always Below 1 Ω
i4-1 - B98-1 (COM1) Always Below 1 Ω
i1-2 or B98-5 (INJ1) - Body ground Always 10 kΩ or higher
i2-2 or B96-4 (INJ2) - Body ground Always 10 kΩ or higher
i3-2 or B96-2 (INJ3) - Body ground Always 10 kΩ or higher
i4-2 or B98-4 (INJ4) - Body ground Always 10 kΩ or higher
i1-1 or B98-1 (COM1) - Body ground Always 10 kΩ or higher
i2-1 or B98-2 (COM2) - Body ground Always 10 kΩ or higher
i3-1 or B98-2 (COM2) - Body ground Always 10 kΩ or higher
i4-1 or B98-1 (COM1) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

10.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER)

10.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1, #2, #3 and #4 Fuel Cut.


e.

Check the four cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.

Result:
Result Proceed to
Engine Idling becomes unstable A
Engine Idling does not change B


HINT:
·

If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change of idle speed when the fuel injection is stopped for that cylinder.





A

REPLACE INJECTOR DRIVER

B

11.CHECK ECM TERMINAL VOLTAGE (THW TERMINAL)
a.
A260250E35
1.302,0.104 1.792,0.396 0.49,0.292 1.844,0.104 2.333,0.396 0.49,0.292 1.625,0.802 1.292,1.542 true 2.198,0.875 2.438,1.542 true 1.385,0.167 1.781,0.354 0.396,0.188 10 false B105 1.938,0.167 2.302,0.354 0.365,0.188 10 false B104 0.063,0.073 0.219,0.208 0.156,0.135 10 false *a 0.979,1.563 1.49,1.813 0.51,0.25 10 false 9(THW) 2.188,1.563 2.615,1.792 0.427,0.229 10 false 14(E2)

Start the engine.


b.

Measure the voltage of the ECM connector.

Standard Voltage:
Tester Connection Condition Specified Condition
E105-9 (THW) - E104-14 (E2) Idling, engine coolant temperature between 60 and 120°C (140 and 248°F) 0.2 to 1.0 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

12.CHECK ECM TERMINAL VOLTAGE (PIM TERMINAL)

NG

17.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
12.CHECK ECM TERMINAL VOLTAGE (PIM TERMINAL)
a.
A260250E37
1.802,0.104 2.292,0.396 0.49,0.292 2.177,0.875 2.333,1.74 true 1.927,0.729 1.573,1.521 true 1.896,0.167 2.375,0.323 0.479,0.156 10 false B104 0.063,0.073 0.25,0.281 0.188,0.208 10 false *a 2.146,1.771 2.844,2.01 0.698,0.24 10 false 14 (E2) 1.25,1.542 1.885,1.813 0.635,0.271 10 false 5 (PIM)

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B104-5 (PIM) - B104-14 (E2) Applied negative pressure of 93 kPa (700 mmHg, 27.5 in.Hg) 0.25 to 0.4 V
B104-5 (PIM) - B104-14 (E2) Applied positive pressure of 150 kPa (1125 mmHg, 44 in.Hg) 1.0 to 1.4 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

13.CHECK ECM TERMINAL VOLTAGE (NE+ AND NE- TERMINALS)

NG

18.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
13.CHECK ECM TERMINAL VOLTAGE (NE+ AND NE- TERMINALS)
a.
A257466E13
2.354,0.354 2.802,0.615 0.448,0.26 2.635,0.969 2.906,1.781 true 2.573,0.958 1.708,1.656 true 0.104,0.052 0.281,0.229 0.177,0.177 10 false *a 1.313,4.063 2.49,4.458 1.177,0.396 10 false 20 ms./DIV. 0.104,1.938 0.281,2.115 0.177,0.177 10 false *b 2.75,2.26 3.427,2.469 0.677,0.208 10 false 5 V/DIV. 0.406,3.333 0.646,3.5 0.24,0.167 10 false NE 0.458,2.615 0.698,2.781 0.24,0.167 10 false G 2.896,3.365 3.24,3.531 0.344,0.167 10 false GND 2.896,2.802 3.24,2.969 0.344,0.167 10 false GND 2.417,0.396 2.792,0.563 0.375,0.167 10 false B103 2.688,1.833 3.188,2 0.5,0.167 10 false 7 (NE+) 1.438,1.688 1.906,1.854 0.469,0.167 10 false 8 (NE-)

While idling the engine, check the waveform between the specified terminals of the ECM connector using an oscilloscope.

Standard:
Tester Connection Specified Condition
B103-7 (NE+) - B103-8 (NE-) Correct waveform appears as shown


Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the engine speed.


Text in Illustration
*a Component with harness connected
(ECM)
*b G and NE Signal Waveform


Result:
Proceed to
OK
NG



OK

14.CHECK ECM TERMINAL VOLTAGE (VPA AND VPA2 TERMINALS)

NG

19.INSPECT CRANKSHAFT POSITION SENSOR
14.CHECK ECM TERMINAL VOLTAGE (VPA AND VPA2 TERMINALS)
a.
A260250E47
0.167,0.25 0.583,0.479 0.417,0.229 0.656,0.25 1.073,0.479 0.417,0.229 0.521,0.74 0.333,1.542 true 0.75,0.74 1.375,1.51 true 0.573,0.74 0.875,1.823 true 0.906,0.74 2.26,1.51 true 0.24,0.292 0.656,0.531 0.417,0.24 10 false A56 0.073,1.563 0.604,1.823 0.531,0.26 10 false 2 (VPA) 0.052,0.021 0.208,0.156 0.156,0.135 10 false *a 1.198,1.563 1.698,1.865 0.5,0.302 10 false 5 (EPA) 1.99,1.531 2.594,1.792 0.604,0.26 10 false 3 (EPA2) 0.604,1.844 1.198,2.073 0.594,0.229 10 false 1 (VPA2) 0.74,0.281 1.5,0.479 0.76,0.198 10 false A57

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Condition Accelerator Pedal Condition Specified Condition
A57-2 (VPA) - A56-5 (EPA) Released 0.6 to 1.0 V
Depressed 2.8 to 3.6 V
A57-1 (VPA2) - A56-3 (EPA2) Released 1.4 to 1.8 V
Depressed 3.6 to 4.4 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

15.CHECK ECM TERMINAL VOLTAGE (THA TERMINAL)

NG

20.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR (ACCELERATOR LINK ASSEMBLY) - ECM)
15.CHECK ECM TERMINAL VOLTAGE (THA TERMINAL)
a.
A260250E39
1.302,0.104 1.792,0.396 0.49,0.292 1.844,0.104 2.333,0.396 0.49,0.292 1.531,0.802 1.271,1.51 true 2.198,0.875 2.542,1.542 true 1.385,0.177 1.75,0.344 0.365,0.167 10 false B105 1.938,0.177 2.323,0.333 0.385,0.156 10 false B104 0.063,0.073 0.219,0.208 0.156,0.135 10 false *a 0.979,1.563 1.573,1.802 0.594,0.24 10 false 10 (THA) 2.219,1.563 2.698,1.823 0.479,0.26 10 false 14 (E2)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B105-10 (THA) - B104-14 (E2) Idling, intake air temperature at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

16.CHECK ECM TERMINAL VOLTAGE (PCR1 AND PCR2 TERMINAL)

NG

21.INSPECT INTAKE AIR TEMPERATURE SENSOR (INTAKE MASS AIR FLOW METER SUB-ASSEMBLY)
16.CHECK ECM TERMINAL VOLTAGE (PCR1 AND PCR2 TERMINAL)
a.
A260250E22
1.302,0.104 1.792,0.396 0.49,0.292 1.844,0.104 2.333,0.396 0.49,0.292 1.521,0.875 0.438,1.542 true 1.698,0.729 1.229,1.719 true 1.698,0.875 1.979,1.542 true 2.198,0.875 2.635,1.719 true 1.385,0.167 1.771,0.354 0.385,0.188 10 false B105 1.927,0.167 2.313,0.365 0.385,0.198 10 false B104 0.021,1.563 0.719,1.781 0.698,0.219 10 false 16 (PCR1) 0.063,0.073 0.313,0.302 0.25,0.229 10 false *a 0.865,1.74 1.469,1.958 0.604,0.219 10 false 2 (PCR2) 2.396,1.74 2.875,1.958 0.479,0.219 10 false 14 (E2) 1.656,1.563 2.26,1.833 0.604,0.271 10 false 14 (E21)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B105-16 (PCR1) - B104-14 (E2) Idling 1.7 to 2.2 V
B105-2 (PCR2) - B105-14 (E21) Idling 1.2 to 1.6 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

NG

22.INSPECT FUEL PRESSURE SENSOR (COMMON RAIL ASSEMBLY)
17.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

NG

18.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B18-2 (PIM) - B104-5 (PIM) Always Below 1 Ω
B18-3 (VC) - B104-13 (VC) Always Below 1 Ω
B18-1 (E) - B104-14 (E2) Always Below 1 Ω
B18-2 (PIM) or B104-5 (PIM) - Body ground Always 10 kΩ or higher
B18-3 (VC) or B104-13 (VC) - Body ground Always 10 kΩ or higher
B18-1 (E) or B104-14 (E2) - Other terminal Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

19.INSPECT CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

20.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR (ACCELERATOR LINK ASSEMBLY) - ECM)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F9-2 (EPA2) - A56-3 (EPA2) Always Below 1 Ω
F9-1 (VPA2) - A57-1 (VPA2) Always Below 1 Ω
F9-4 (VCPA) - A56-6 (VCPA) Always Below 1 Ω
F9-3 (EPA) - A56-5 (EPA) Always Below 1 Ω
F9-5 (VPA) - A57-2 (VPA) Always Below 1 Ω
F9-2 (EPA2) or A56-3 (EPA2) - Body ground Always 10 kΩ or higher
F9-1 (VPA2) or A57-1 (VPA2) - Body ground Always 10 kΩ or higher
F9-4 (VCPA) or A56-6 (VCPA) - Body ground Always 10 kΩ or higher
F9-3 (EPA) or A56-5 (EPA) - Body ground Always 10 kΩ or higher
F9-5 (VPA) or A57-2 (VPA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ACCELERATOR PEDAL POSITION SENSOR (ACCELERATOR LINK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR (ACCELERATOR LINK ASSEMBLY) - ECM)

21.INSPECT INTAKE AIR TEMPERATURE SENSOR (INTAKE MASS AIR FLOW METER SUB-ASSEMBLY)
a.

Inspect the intake air temperature sensor (intake mass air flow meter sub-assembly) (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION).


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (INTAKE MASS AIR FLOW METER SUB-ASSEMBLY) - ECM)

NG

REPLACE INTAKE AIR TEMPERATURE SENSOR (INTAKE MASS AIR FLOW METER SUB-ASSEMBLY)

22.INSPECT FUEL PRESSURE SENSOR (COMMON RAIL ASSEMBLY)
a.

Inspect the fuel pressure sensor (common rail assembly) (Click hereEngine / Hybrid System>N04C-VL (FUEL)>COMMON RAIL>INSPECTION).


Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR (COMMON RAIL ASSEMBLY) - ECM)

NG

REPLACE FUEL PRESSURE SENSOR (COMMON RAIL ASSEMBLY)

23.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR (COMMON RAIL ASSEMBLY) - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B105-16 (PCR1) - B93-2 (PCR1) Always Below 1 Ω
B104-13 (VC) - B93-1 (VC1) Always Below 1 Ω
B104-14 (E2) - B93-3 (E1) Always Below 1 Ω
B105-2 (PCR2) - B93-5 (PCR2) Always Below 1 Ω
B105-13 (VC2) - B93-6 (VC2) Always Below 1 Ω
B105-14 (E21) - B93-4 (E2) Always Below 1 Ω
B105-16 (PCR1) or B93-2 (PCR1) - Body ground Always 10 kΩ or higher
B104-13 (VC) or B93-1 (VC1) - Body ground Always 10 kΩ or higher
B105-2 (PCR2) or B93-5 (PCR2) - Body ground Always 10 kΩ or higher
B105-13 (VC2) or B93-6 (VC2) - Body ground Always 10 kΩ or higher
B104-14 (E2) or B93-3 (E1) - Other terminals Always 10 kΩ or higher
B105-14 (E21) or B93-4 (E2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

24.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PRESSURE SENSOR (COMMON RAIL ASSEMBLY) - ECM)

24.REPLACE ECM
a.

Replace the ECM (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECM>REMOVAL).

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



b.

Check the volume of black smoke in the exhaust gas.

OK:

Black smoke is not present.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY