Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P041B  EGR Temperature Sensor "B" Circuit Range/Performance  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P041B EGR Temperature Sensor "B" Circuit Range/Performance Diagnosis Condition:
Engine start:
·

The conditions described below remain for 20 seconds or more.

-

The engine speed is 570 to 1000 rpm or less.

-

Fuel injection quantity is 35 mm3/st or less.

-

Engine coolant temperature is in the range of -30 to 30°C (-22 to 86°F).

-

Battery voltage is in the range of 10 V to 16 V

-

The exhaust brake is not actuated throughout this DCY.



Engine running:
·

The conditions described below remain for 11 seconds or more.

-

Battery voltage is in the range of 10 V to 16 V

-

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


·

In addition, the conditions described below remain for 40 seconds or more.

-

The engine speed is 1200 rpm or more.

-

Fuel injection quantity is 25 mm3/st or more.

-

The EGR gas flow rate is 10 kg/h or more.

-

A change in the engine speed is 664 rpm or less.

-

A change in fuel injection quantity is 78 mm3/st or less.

-

Atmospheric pressure is higher than 75 kPa.

-

Vehicle speed is 21 km/h (13 mph) or more.

-

Intake air quantity is 30 g/sec or more.

-

Intake air temperature is -10°C (14°F) or more.

-

Exhaust brake is not actuated.



Malfunction Status:
Engine start:

The parameters described above are counted for at least 20 seconds and the average EGR temperature is 70°C (158°F) or more.


Engine running:

The calculated EGR cooler efficiency is 115% or more or 40% or less. In addition, the absolute value obtained by subtracting the actual intake manifold temperature from the calculated intake manifold temperature is 60°C (140°F) or less. In addition, the calculated inter cooler efficiency is 45 to 65% or more.


Malfunction Duration:
Engine start:

20 seconds or more


Engine running:

-


·

Exhaust gas temperature sensor (for EGR cooler side)

·

Intake air temperature sensor (for intake manifold side)

·

Manifold absolute pressure sensor

·

Intake air temperature sensor (for intercooler side)

·

ECM


Class B2 DTC stored

MONITOR DESCRIPTION

The exhaust gas temperature sensor (for EGR cooler side) consistently measures temperature at the outlet of the EGR cooler.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P041B After warming up the engine, drive at an engine speed of 1200 rpm or higher


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read Current DTCs.

Result:
Result Proceed to
DTC P041B is output A
DTC P041B and other DTCs are output B


HINT:
·

If P0234 or P0299 is output, it may have been detected due to a turbocharger system malfunction.

·

If P0401 or P0402 is output, it may have been detected due to a EGR system malfunction.





A

2.CHECK CONNECTOR CONNECTION CONDITION

B

2.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the exhaust gas temperature sensor (for EGR cooler side) connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)

NG

23.CONNECT SECURELY
3.CHECK EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)
a.

Check the installation of the exhaust gas temperature sensor (for EGR cooler side).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the exhaust gas temperature sensor (for EGR cooler side).


Result:
Proceed to
OK
NG



OK

4.INSPECT EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)

NG

21.REPAIR OR REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)
4.INSPECT EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)
a.

Inspect the exhaust gas temperature sensor (for EGR cooler side).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)

NG

20.REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)
5.CHECK EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)
A227773C20
0.396,1.042 0.875,1.281 0.479,0.24 1,1.76 1.552,1.25 true 2.583,1.813 2.021,1.219 true 0.156,0.135 0.479,0.427 0.323,0.292 10 false *a 0.49,1.094 0.917,1.26 0.427,0.167 10 false B147 0.771,1.792 1.198,1.958 0.427,0.167 10 false THG 2.583,1.854 3.01,2.021 0.427,0.167 10 false E2
*a Front view of wire harness connector
(to Exhaust Gas Temperature Sensor (for EGR Cooler Side))


a.

Disconnect the exhaust gas temperature sensor (for EGR cooler side) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B147-1 (THG) - B147-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



NG

6.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE) - ECM)

OK

11.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
6.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE) - ECM)
A405886C06
1.5,0.083 1.917,0.354 0.417,0.271 1.646,0.146 1.802,0.344 0.156,0.198 10 false M 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a
*a Signal Check Harness Lead Connector


A405887C17
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


a.

Disconnect the ECM connector.


b.

Disconnect the exhaust gas temperature sensor (for EGR cooler side) connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M-30 - Body ground and other terminals Always 10 kΩ or higher
M-54 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK HARNESS AND CONNECTOR
A227773C21
0.417,0.948 0.938,1.208 0.521,0.26 1,1.771 1.552,1.24 true 2.385,1.76 2.01,1.24 true 0.5,0.99 0.979,1.302 0.479,0.313 10 false B147 0.156,0.115 0.635,0.427 0.479,0.313 10 false *a 0.729,1.792 1.208,2.104 0.479,0.313 10 false THG 2.375,1.802 2.854,2.115 0.479,0.313 10 false E2
*a Front view of wire harness connector
(to Exhaust Gas Temperature Sensor (for EGR Cooler Side))


A405886C06
1.5,0.083 1.917,0.354 0.417,0.271 1.646,0.146 1.802,0.344 0.156,0.198 10 false M 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a
*a Signal Check Harness Lead Connector


A405887C17
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


a.

Disconnect the ECM connector.


b.

Disconnect the exhaust gas temperature sensor (for EGR cooler side) connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M-54 - B147-1 (THG) Always Below 1 Ω
M-30 - B147-2 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.REPLACE ECM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.REPLACE ECM
a.

Replace the ECM.


Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
11.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Check the installation of the intake air temperature sensor (for intake manifold side).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the intake air temperature sensor (for intake manifold side).


Result:
Proceed to
OK
NG



OK

12.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)

NG

28.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
12.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Inspect the intake air temperature sensor (for intake manifold side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

13.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)

NG

27.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
13.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Check the installation of the intake air temperature sensor (for intercooler side).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the intake air temperature sensor (for intercooler side).


Result:
Proceed to
OK
NG



OK

14.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)

NG

26.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
14.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Inspect the intake air temperature sensor (for intercooler side).


Result:
Proceed to
OK
NG



OK

15.CHECK VACUUM HOSE

NG

25.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
15.CHECK VACUUM HOSE
a.

Make sure the vacuum hose is not clogged, ruptured, or cracked.


b.

Make sure the pipe on the intake manifold side is not clogged.


Result:
Proceed to
OK
NG



OK

16.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

24.REPAIR OR REPLACE VACUUM HOSE
16.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Turn the ignition switch off.


A241069C42
0.427,1.125 0.854,1.385 0.427,0.26 0.958,1.76 1.375,1.344 true 2.229,1.74 1.854,1.344 true 0.521,1.167 0.979,1.365 0.458,0.198 10 false B18 0.25,0.188 0.708,0.385 0.458,0.198 10 false *a 0.854,1.781 1.313,1.979 0.458,0.198 10 false E 2.271,1.76 2.729,1.958 0.458,0.198 10 false VC
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


b.

Disconnect the manifold absolute pressure sensor connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B18-3 (VC) - B18-1 (E) Ignition switch ON 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

17.CHECK DTC OUTPUT

NG

22.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR CIRCUIT
17.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P041B is output A
DTCs are not output B




A

18.REPLACE ECM

B

END

18.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
19.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

20.REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)
a.

Replace the exhaust gas temperature sensor (for EGR cooler side).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
21.REPAIR OR REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)
a.

Repair or replace the exhaust gas temperature sensor (for EGR cooler side).

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the exhaust gas temperature sensor (for EGR cooler side).



Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
22.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR CIRCUIT
a.

Inspect manifold absolute pressure sensor circuit.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>P0107


Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
23.CONNECT SECURELY
a.

Connect securely the exhaust gas temperature sensor (for EGR cooler side).

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
24.REPAIR OR REPLACE VACUUM HOSE
a.

Repair or replace vacuum hose.


Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
25.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Replace the intake air temperature sensor (for intercooler side).


Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
26.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Repair or replace the intake air temperature sensor (for intercooler side).

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the intake air temperature sensor (for intercooler side).



Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
27.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Replace the intake air temperature sensor (for intake manifold side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
28.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Repair or replace the intake air temperature sensor (for intake manifold side).

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the intake air temperature sensor (for intake manifold side).



Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT