Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0088  Fuel Rail/System Pressure - Too High  P016E  Closed Loop Fuel Pressure Control At Limit - Pressure Too High  P016F  Closed Loop Fuel Pressure Control At Limit - Pressure Too Low  P2635  Fuel Pump "A" Low Flow/Performance  


DESCRIPTION

A451044C02
0.74,0.406 1.052,0.563 0.313,0.156 10 false *1 0.948,1.063 1.26,1.219 0.313,0.156 10 false *2 1.823,1.073 2.135,1.229 0.313,0.156 10 false *3 2.344,1.375 2.656,1.531 0.313,0.156 10 false *4 2.354,1.813 2.667,1.969 0.313,0.156 10 false *5 3.719,2.167 4.031,2.323 0.313,0.156 10 false *6 5.708,2.198 6.021,2.354 0.313,0.156 10 false *7 1.479,3.344 1.792,3.5 0.313,0.156 10 false *8 3.344,3.344 3.813,3.5 0.469,0.156 10 false *9 3.656,4.323 4.125,4.479 0.469,0.156 10 false *10 4.323,4.802 4.792,4.958 0.469,0.156 10 false *11 6.177,4.813 6.646,4.969 0.469,0.156 10 false *12 3.042,5.865 3.51,6.021 0.469,0.156 10 false *13 2.51,6.385 2.979,6.542 0.469,0.156 10 false *14 2.51,6.906 2.979,7.063 0.469,0.156 10 false *15 5.75,7.365 6.219,7.521 0.469,0.156 10 false *16 0.104,5.344 0.573,5.5 0.469,0.156 10 false *17 0.094,5.688 0.563,5.844 0.469,0.156 10 false *18
*1 Injector Assembly *2 Pressure Discharge Valve
*3 Common Rail Assembly *4 Pressure Limiter
*5 Supply Pump Assembly *6 Feed Pump
*7 Suction Control Valve *8 Exhaust Fuel Addition Injector Assembly
*9 Fuel Addition Cut Valve Assembly *10 Diesel Fuel Filter Assembly
*11 Overflow Valve *12 Fuel Filter Element Set
*13 Priming Pump *14 Fuel Filter Element Sub-assembly
*15 Level Warning Switch *16 Fuel Tank
*17 for Engine Side *18 for Chassis Side
V100143

High Pressure Fuel
V100146

Suction Fuel
V100155

Return Fuel - -


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0088 Fuel Rail/System Pressure - Too High Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Common rail pressure exceeds 232 MPa.


Malfunction Duration:

5 seconds or more


·

Fuel pressure sensor

·

Supply pump assembly

·

Common rail assembly

·

Diesel fuel filter assembly

·

Pressure discharge valve

·

Harness or connector


- DTC stored
P016E Closed Loop Fuel Pressure Control At Limit - Pressure Too High Diagnosis Condition:
·

The following conditions continue for at least 10 seconds:

-

Engine is running.

-

Fuel injection quantity 10 mm3/st or more



Malfunction Status:

Abnormally high fuel pressure inside common rail is detected.


Malfunction Duration:

10 seconds or more


·

Diesel fuel filter assembly

·

Fuel pressure sensor

·

Supply pump assembly

·

Common rail assembly

·

Harness or connector

·

Pressure discharge valve


Class B1 DTC stored
P016F Closed Loop Fuel Pressure Control At Limit - Pressure Too Low Diagnosis Condition:
·

The following conditions continue for at least 5 seconds:

-

Engine is running.

-

Fuel injection quantity 10 mm3/st or more



Malfunction Status:

(Actual common rail pressure - target common rail pressure) -15 MPa or more for 15 seconds.


Malfunction Duration:

5 seconds or more


·

Fuel line

·

Diesel fuel filter assembly

·

Fuel pressure sensor

·

Supply pump assembly

·

Common rail assembly

·

Harness or connector

·

Exhaust fuel addition injector assembly

·

Pressure discharge valve


Class A DTC stored
P2635 Fuel Pump "A" Low Flow/Performance Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

Engine is running.

·

Common rail pressure sensor; no malfunction.


Malfunction Status:
·

Common rail pressure threshold or more

·

15 sec continue


Malfunction Duration:

15 seconds or more


·

Supply pump assembly

·

ECM

·

Fuel pressure sensor

·

Harness or connector

·

Pressure discharge valve


- DTC stored

MONITOR DESCRIPTION

·

The common rail pressure is controlled by the discharge of the supply pump and pressure discharge valve.

·

The supply pump discharge rate is adjusted by the SCV (suction control valve).


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0088
P016E
P016F
P2635
After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).

·

After replacing the suction control valve or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read Current DTCs.

Result:
Result Proceed to
DTC P0088, P016E, P016F or P2635 is output A
DTCs other than P0088, P016E, P016F or P2635 are output B




A

2.CHECK FUEL

B

2.CHECK FUEL
a.

Check that the fuel meets to require with ambient air temperature.


Result:
Proceed to
OK
NG



OK

3.INSPECT SUPPLY PUMP ASSEMBLY

NG

36.REPLACE FUEL
3.INSPECT SUPPLY PUMP ASSEMBLY
a.

Check if fuel is leaking or seeping out of the supply pump.


Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL FILTER ASSEMBLY (FOR FUELTANK SIDE)

NG

35.REPAIR OR REPLACE SUPPLY PUMP ASSEMBLY
4.INSPECT FUEL FILTER ASSEMBLY (FOR FUELTANK SIDE)
a.

Check the fuel filter element sub-assembly.

i.

Has the replacement period expired.


ii.

Is it dirty, damaged, or clogged.


iii.

Is it a genuine part.



b.

Check the fuel filter element sub-assembly connections for air breathing and fuel leakage.

HINT:

If the air bleeding plug is loosened, it is caused by breathing the air into the fuel system.



Standard:
Condition Specified Condition
Ignition switch off Below the upper level of the fuel filter element sub-assembly
Engine idling Fuel level does not continue dropping while engine is running at high speed


Result:
Proceed to
OK
NG



OK

5.INSPECT FUEL PIPE

NG

33.REPAIR OR REPLACE FUEL FILTER ASSEMBLY
5.INSPECT FUEL PIPE
a.

Check if the fuel pipe and hose between the fuel tank and fuel filter element sub-assembly are clogged, punctured, or bent.


b.

Make sure the fuel pipe joint bolts are not loose.


c.

Check the fuel filter connections for air breathing and fuel leakage.

HINT:

If the air bleeding plug is loosened, it is caused by breathing the air into the fuel system.



Result:
Proceed to
OK
NG



OK

6.CHECK FUEL TANK FEED PIPE

NG

31.REPAIR OR REPLACE FUEL PIPE
6.CHECK FUEL TANK FEED PIPE
a.

Make sure the fuel tank feed pipe is not clogging.


Result:
Proceed to
OK
NG



OK

7.INSPECT FUEL TANK BREATHER HOSE

NG

29.REPAIR OR REPLACE FUEL TANK FEED PIPE
7.INSPECT FUEL TANK BREATHER HOSE
a.

Check if the breather hose is clogged, punctured, or bent.


b.

Make sure the check valve is functioning normally.


Result:
Proceed to
OK
NG



OK

8.INSPECT FUEL TANK ASSEMBLY

NG

27.REPAIR OR REPLACE FUEL TANK BREATHER HOSE
8.INSPECT FUEL TANK ASSEMBLY
a.

Drain fuel out of the fuel tank assembly and check if there are foreign objects inside the tank.


Result:
Proceed to
OK
NG



OK

9.INSPECT FUEL PIPE (HIGH PRESSURE SIDE)

NG

24.REPAIR FUEL TANK ASSEMBLY
9.INSPECT FUEL PIPE (HIGH PRESSURE SIDE)
a.

Make sure the fuel high-pressure pipe is not leaking fuel.


b.

Check the common rail for fuel leakage.


Result:
Proceed to
OK
NG



OK

10.CHECK FUEL FILTER ELEMENT SET (FOR ENGINE SIDE)

NG

22.REPAIR OR REPLACE FUEL PIPE (HIGH PRESSURE SIDE)
10.CHECK FUEL FILTER ELEMENT SET (FOR ENGINE SIDE)
a.

Check for fuel filter element set.

i.

Has the replacement period expired.


ii.

Is it a genuine part.



b.

Check for bleeding the air from the fuel filter element set at adequate levels.


c.

Check the fuel filter connections for breathing the air and fuel leak age.

HINT:

If the air bleeding plug is loosened, it is caused by breathing the air into the fuel system.



Result:
Proceed to
OK
NG



OK

11.CHECK CONNECTOR CONNECTION CONDITION

NG

20.REPAIR OR REPLACE FUEL FILTER ELEMENT SET
11.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the fuel pressure sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

12.CHECK COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)

NG

34.CONNECT SECURELY
12.CHECK COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.
A451756C01
0.313,0.979 0.833,1.229 0.521,0.25 0.958,1.594 1.344,1.135 true 2.385,1.594 2.031,1.104 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 0.406,1.01 0.771,1.25 0.365,0.24 10 false B140 0.688,1.635 1,1.833 0.313,0.198 10 false VC1 2.417,1.635 2.729,1.833 0.313,0.198 10 false E2
*a Front view of wire harness connector
(to Fuel Pressure Sensor Connector)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B140-1 (VC1) - B140-3 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (POOR CONTACT)

NG

32.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.CHECK HARNESS AND CONNECTOR (POOR CONTACT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data list / Common Rail Pressure, G Active Status and NE Active Status


e.

Start the engine and warm it up.


f.

Check the output data of the following items while grasping the harness and swung it between ECM.

·

Fuel pressure sensor

·

Crankshaft position sensor

·

Camshaft position sensor



g.

Jiggle the harness between the ECM and crankshaft position sensor, and the harness between the ECM and camshaft position sensor. Check whether "NE Active Status" and "G Active Status" change as the harnesses are jiggled.

Standard:

stabilized at a constant value even when swung harness



Result:
Proceed to
OK
NG



OK

14.CHECK CONNECTOR CONNECTION CONDITION (PRESSURE DISCHARGE VALVE)

NG

30.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.CHECK CONNECTOR CONNECTION CONDITION (PRESSURE DISCHARGE VALVE)
a.

Check the connector connection for the pressure discharge valve connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

15.INSPECT PRESSURE DISCHARGE VALVE

NG

28.CONNECT SECURELY
15.INSPECT PRESSURE DISCHARGE VALVE
a.

Inspect the pressure discharge valve.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>COMMON RAIL>INSPECTION


Result:
Proceed to
OK
NG



OK

16.CHECK CONNECTOR CONNECTION CONDITION (SUCTION CONTROL VALVE)

NG

26.REPLACE COMMON RAIL ASSEMBLY
16.CHECK CONNECTOR CONNECTION CONDITION (SUCTION CONTROL VALVE)
a.

Check the connector connection for the suction control valve connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

17.INSPECT SUCTION CONTROL VALVE

NG

25.CONNECT SECURELY
17.INSPECT SUCTION CONTROL VALVE
a.

Inspect the suction control valve.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL SUPPLY PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

18.CHECK FUEL RETURN PIPE AND HOSE

NG

23.REPLACE SUCTION CONTROL VALVE
18.CHECK FUEL RETURN PIPE AND HOSE
a.

Check if the fuel return pipe and hose are clogged, punctured, or bent.


Result:
Proceed to
OK
NG



OK

19.CHECK DTC OUTPUT

NG

21.REPAIR OR REPLACE FUEL RETURN PIPE AND HOSE
19.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

20.REPAIR OR REPLACE FUEL FILTER ELEMENT SET
a.

Repair or replace the fuel filter element set.


Result:
Proceed to
NEXT



NEXT

11.CHECK CONNECTOR CONNECTION CONDITION
21.REPAIR OR REPLACE FUEL RETURN PIPE AND HOSE
a.

repair or replace fuel return pipe and hose.


Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
22.REPAIR OR REPLACE FUEL PIPE (HIGH PRESSURE SIDE)
a.

Repair or replace the fuel pipe (high pressure side )


Result:
Proceed to
NEXT



NEXT

10.CHECK FUEL FILTER ELEMENT SET (FOR ENGINE SIDE)
23.REPLACE SUCTION CONTROL VALVE
a.

Replace the suction control valve.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>SUCTION CONTROL VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

18.CHECK FUEL RETURN PIPE AND HOSE
24.REPAIR FUEL TANK ASSEMBLY
a.

Remove the foreign object and clean the fuel tank assembly.


Result:
Result Proceed to
If the fault is restored. A
When the fault is not restored. B



A

19.CHECK DTC OUTPUT

B

9.INSPECT FUEL PIPE (HIGH PRESSURE SIDE)
25.CONNECT SECURELY
a.

Connect securely the suction control valve connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

17.INSPECT SUCTION CONTROL VALVE
26.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CHECK CONNECTOR CONNECTION CONDITION (SUCTION CONTROL VALVE)
27.REPAIR OR REPLACE FUEL TANK BREATHER HOSE
a.

Repair or replace the fuel tank breather hose.


Result:
Proceed to
NEXT



NEXT

8.INSPECT FUEL TANK ASSEMBLY
28.CONNECT SECURELY
a.

Connect securely the pressure discharge valve connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

15.INSPECT PRESSURE DISCHARGE VALVE
29.REPAIR OR REPLACE FUEL TANK FEED PIPE
a.

Repair or replace the fuel tank feed pipe.


Result:
Proceed to
NEXT



NEXT

7.INSPECT FUEL TANK BREATHER HOSE
30.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK CONNECTOR CONNECTION CONDITION (PRESSURE DISCHARGE VALVE)
31.REPAIR OR REPLACE FUEL PIPE
a.

Repair or replace the fuel pipe.


Result:
Proceed to
NEXT



NEXT

6.CHECK FUEL TANK FEED PIPE
32.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CHECK HARNESS AND CONNECTOR (POOR CONTACT)
33.REPAIR OR REPLACE FUEL FILTER ASSEMBLY
a.

Repair or replace the fuel filter assembly.


Result:
Result Proceed to
If the fault is restored. A
When the fault is not restored. B



A

19.CHECK DTC OUTPUT

B

5.INSPECT FUEL PIPE
34.CONNECT SECURELY
a.

Connect securely the air pressure sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

12.CHECK COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
35.REPAIR OR REPLACE SUPPLY PUMP ASSEMBLY
a.

Repair or replace the supply pump assembly.


Result:
Result Proceed to
If the fault is restored. A
When the fault is not restored. B



A

19.CHECK DTC OUTPUT

B

4.INSPECT FUEL FILTER ASSEMBLY (FOR FUELTANK SIDE)
36.REPLACE FUEL
a.

Replace fuel with required ambient temperature.


Result:
Proceed to
NEXT



NEXT

3.INSPECT SUPPLY PUMP ASSEMBLY