Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0096  Intake Air Temperature Sensor 2 Circuit Range/Performance Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0096 Intake Air Temperature Sensor 2 Circuit Range/Performance Bank 1 Diagnosis Condition:
Engine start:
·

The conditions described below remain for 20 seconds or more.

-

The engine speed is range of 570 to 1,000 rpm

-

Fuel injection quantity is at least 4 to 35 mm3/st or less.

-

Engine coolant temperature is in the range of -30 to 55°C (-22 to 131°F)

-

The battery voltage is in the range of 10 to 16 V.



Engine running:
·

The conditions described below remain for 11 seconds or more.

-

The battery voltage is in the range of 10 to 16 V.

-

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


·

In addition, the conditions described below remain for 40 seconds or more.

-

The engine speed is 1200 rpm or more.

-

Fuel injection quantity is 25 mm3/st or more.

-

The EGR gas flow rate is 10 kg/h or more.

-

A change in the engine speed is 664 rpm or less.

-

A change in fuel injection quantity is 78 mm3/st or less.

-

Atmospheric pressure is higher than 75 kPa.

-

Vehicle speed is 21 km/ h (13 mph) or more.

-

Intake air quantity is 30 g/sec or more.

-

Intake air temperature is -10°C (14°F) or more.

-

Exhaust brake is not actuated.



Malfunction Status:
Engine start:
·

Judged when the average temperature difference between the intake air temperature sensor (for intake manifold side) and the intake air temperature sensor (built into mass air flow meter) is 30°C (86°F) or more while the average temperature difference between the intake air temperature sensor (for intake manifold side) and the intake air temperature sensor (for intercooler side) is 30°C (86°F) or more.


Engine running:
·

Judged when the calculated EGR cooler efficiency is greater than 80%, the difference between the calculated intake manifold air intake temperature and the actual intake air is higher than 70°C (158°F) or less than -70°C (-94°F), and the calculated intercooler efficiency is higher than the specified value (45% or more when the vehicle speed is 21 km/h (13 mile), 65% or more when the vehicle speed is 40 km/h (25 mile)).


Malfunction Duration:

-


·

Intake air temperature sensor (for intercooler side)

·

Intake air temperature sensor (built into mass air flow meter)

·

Intake air temperature sensor (for intake manifold side)

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

The intake air temperature sensor (for intake manifold side) installed to the intake manifold consistently measures intake manifold temperature.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0096 After engine warmup, run in engine speed 1200 rpm


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read Current DTCs.

Result:
Result Proceed to
DTC P0096 is output A
DTC P0096 and other DTC are output B


HINT:

When P0401, P0402, P0234, P0299 or P22D3 is output, it may have been detected due to a malfunction in the turbocharger system or EGR system.




A

2.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)

B

2.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Check the connector connection for the intake air temperature sensor (for intake manifold side) connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)

NG

26.CONNECT SECURELY
3.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Check the installation of the intake air temperature sensor (for intake manifold side).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the intake air temperature sensor (for intake manifold side).


Result:
Proceed to
OK
NG



OK

4.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)

NG

24.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
4.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Inspect the intake air temperature sensor (for intake manifold side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)

NG

21.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
5.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
A227773C19
0.385,1.073 0.833,1.375 0.448,0.302 0.854,1.802 1.563,1.229 true 2.552,1.74 2.01,1.24 true 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 0.5,1.146 0.844,1.375 0.344,0.229 10 false B13 0.635,1.781 0.948,1.979 0.313,0.198 10 false E2 2.594,1.76 3.031,1.958 0.438,0.198 10 false THA
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (for Intake Manifold Side))


a.

Disconnect the intake air temperature sensor (for intake manifold side).


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B13-2 (THA) - B13-1 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

6.CHECK MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)

NG

18.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE) - ECM)
6.CHECK MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
a.

Check the installation of the intake mass air flow meter.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the mass air flow meter.


Result:
Proceed to
OK
NG



OK

7.INSPECT INTAKE AIR TEMPERATURE SENSOR (MASS AIR FLOW METER)

NG

16.REPAIR OR REPLACE MASS AIR FLOW METER
7.INSPECT INTAKE AIR TEMPERATURE SENSOR (MASS AIR FLOW METER)
a.

Inspect the Intake air temperature sensor (built into mass air flow meter).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)

NG

15.REPLACE MASS AIR FLOW METER
8.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Check the installation of the intake air temperature sensor (for intercooler side).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the intake air temperature sensor (for intercooler side).


Result:
Proceed to
OK
NG



OK

9.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)

NG

23.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
9.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Inspect the intake air temperature sensor (for intercooler side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR HOSE

NG

20.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
10.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR HOSE
a.

Make sure the manifold absolute pressure sensor hose is not clogged, ruptured, or cracked.


b.

Make sure the pipe on the intake manifold side is not clogged.


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR)

NG

17.REPAIR OR REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR HOSE
11.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR)
A241069C43
0.385,1.073 0.833,1.375 0.448,0.302 0.969,1.771 1.385,1.354 true 2.219,1.75 1.833,1.354 true 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 0.5,1.146 0.813,1.344 0.313,0.198 10 false B18 0.844,1.802 1.156,2 0.313,0.198 10 false E 2.25,1.792 2.563,1.99 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B18-3 (VC) - B18-1 (E) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

12.CHECK DTC OUTPUT

NG

CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (POWER SOURCE)

12.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Result Proceed to
DTC P0096 is output A
DTCs are not output B



A

13.REPLACE ECM

B

END

13.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

15.REPLACE MASS AIR FLOW METER

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
16.REPAIR OR REPLACE MASS AIR FLOW METER
a.

Mass air flow meter carry out air blow from the suction port of the main body and install it properly.

HINT:

If damaged, replace the mass air flow meter.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
17.REPAIR OR REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR HOSE
a.

Replace or replace the manifold absolute pressure sensor hose.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
18.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE) - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the intake air temperature sensor (for intake manifold side) connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C13
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-63 - Body ground and other terminals Always 10 kΩ or higher
E-54 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE) - ECM)

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
19.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE) - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the intake air temperature sensor (for intake manifold side) connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A227773C19
0.385,1.073 0.833,1.375 0.448,0.302 0.854,1.802 1.563,1.229 true 2.552,1.74 2.01,1.24 true 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 0.5,1.146 0.844,1.375 0.344,0.229 10 false B13 0.635,1.781 0.948,1.979 0.313,0.198 10 false E2 2.594,1.76 3.031,1.958 0.438,0.198 10 false THA
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (for Intake Manifold Side))


A405887C12
1.5,0.115 1.875,0.385 0.375,0.271 0.26,0.208 0.573,0.406 0.313,0.198 10 false *a 1.635,0.167 1.792,0.365 0.156,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-63 - B13-2 (THA) Always Below 1 Ω
E-54 - B13-1 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)

NG

22.REPAIR OR REPLACE HARNESS OR CONNECTOR
20.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Replace the intake air temperature sensor (for intercooler side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
21.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Replace the intake air temperature sensor (for intake manifold side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
22.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
23.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Repair or replace the intake air temperature sensor (for intercooler side).

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the intake air temperature sensor (for intercooler side).



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
24.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Repair or replace the intake air temperature sensor (for intake manifold side).

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the intake air temperature sensor (for intake manifold side).



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
25.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
26.CONNECT SECURELY
a.

Connect securely the intake air temperature sensor (for intake manifold side) connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT