Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P200C  Particulate Filter Over Temperature Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P200C Particulate Filter Over Temperature Bank 1 Diagnosis Condition:

The engine must not be stopped.


Malfunction Status:

Value of the No. 4 exhaust gas temperature sensor remains at 965°C (1769°F) or higher for 5 seconds.


Malfunction Duration:

5 seconds or more


·

Monolithic converter assembly

·

Exhaust fuel addition injector

·

No. 4 exhaust gas temperature sensor

·

ECM


Class C DTC stored

MONITOR DESCRIPTION

·

The ECM constantly calculates and accumulates the amount of soot deposit from the engine.

The regeneration mode is selected by the data based on this value and a regeneration is started.

·

If an abnormally high temperature is detected in the No. 4 exhaust temperature sensor located downstream of the monolithic converter assembly, an error is detected.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P200C PM forced regeneration

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Turn the ignition switch to ON and turn the ignition switch off and wait for 5 seconds or more.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P200C is output A
DTC P200C and other DTC are output B




A

2.CHECK EXHAUST PIPE

B

2.CHECK EXHAUST PIPE
a.

Make sure there is no dirt, damage or clogging in the sensing unit of exhaust pipe.


Result:
Proceed to
OK
NG



NG

3.REPLACE MONOLITHIC CONVERTER ASSEMBLY

OK

10.CHECK NO. 4 EXHAUST GAS TEMPERATURE SENSOR
3.REPLACE MONOLITHIC CONVERTER ASSEMBLY
a.

Replace the monolithic converter assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>MONOLITHIC CONVERTER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.PERFORM PM FORCED REGENERATION
4.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Proceed to
NEXT



NEXT

5.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR
5.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / DPR Exhaust Temperature (OUT)


e.

Read the value displayed on the GTS.

Standard:

DPR Exhaust Temperature (OUT): below 800°C (1472°F)



Result:
Proceed to
OK
NG



OK

6.CHECK READ VALUE USING GTS (INJECTION VOLUME, ENGINE SPEED)

NG

11.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR
6.CHECK READ VALUE USING GTS (INJECTION VOLUME, ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Injection Volume


e.

Read the value displayed on the GTS.


Standard:
Item Condition Reference Value
Engine Speed
·

Engine speed: 1500 rpm

·

Engine coolant temperature: 80°C or higher

·

Shift position N

·

A/C OFF

·

Air compressor OFF


Speed fluctuation amount is 15 rpm or less
Injection Volume 5 mm3/st or more


Result:
Proceed to
OK
NG



OK

7.CHECK CONNECTOR CONNECTION CONDITION (NO. 4 EXHAUST GAS TEMPERATURE SENSOR)

NG

9.REPLACE INJECTOR ASSEMBLY
7.CHECK CONNECTOR CONNECTION CONDITION (NO. 4 EXHAUST GAS TEMPERATURE SENSOR)
a.

Check the connector connection for the No. 4 exhaust gas temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

10.CHECK NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NG

8.CONNECT SECURELY
8.CONNECT SECURELY
a.

Connect securely the No. 4 exhaust gas temperature sensor.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

18.PERFORM PM FORCED REGENERATION
9.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

18.PERFORM PM FORCED REGENERATION
10.CHECK NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 4 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the No. 4 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

11.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NG

24.REPAIR OR REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
11.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 4 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

12.INSPECT EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

NG

23.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
12.INSPECT EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Inspect the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

13.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY

NG

22.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
13.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY
a.

Inspect the fuel addition cut valve assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL ADDITION CUT VALVE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

14.CHECK FUEL PIPE SUB-ASSEMBLY

NG

21.REPLACE FUEL ADDITION CUT VALVE ASSEMBLY
14.CHECK FUEL PIPE SUB-ASSEMBLY
a.

Check the fuel pipes for damage, fuel leaks, bleeding, etc.


Result:
Proceed to
OK
NG



OK

15.PERFORM PM FORCED REGENERATION

NG

20.REPAIR OR REPLACE FUEL PIPE SUB-ASSEMBLY
15.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
16.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read Current DTCs.

Result:
Result Proceed to
DTC P200C is output A
DTCs are not output B




A

17.REPLACE ECM

B

END

17.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

18.PERFORM PM FORCED REGENERATION
18.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
19.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

20.REPAIR OR REPLACE FUEL PIPE SUB-ASSEMBLY
a.

Repair or replace the fuel pipe sub-assembly.


Result:
Proceed to
NEXT



NEXT

15.PERFORM PM FORCED REGENERATION
21.REPLACE FUEL ADDITION CUT VALVE ASSEMBLY
a.

Replace the fuel addition cut valve assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL ADDITION CUT VALVE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.PERFORM PM FORCED REGENERATION
22.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Replace the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.PERFORM PM FORCED REGENERATION
23.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 4 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

18.PERFORM PM FORCED REGENERATION
24.REPAIR OR REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Clean the sensing unit and install it properly.

HINT:

If damaged, replace the No. 4 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

18.PERFORM PM FORCED REGENERATION