| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2BAE | NOx Exceedence - NOx Control Monitoring System | Diagnosis Condition:
The length of time taken from the previous feedback is 180 seconds or less. Malfunction Status: Judged when the urea solution additive amount feedback is reset twice at intervals of within 10 seconds Malfunction Duration: Within 10 seconds |
·
No. 1 nitrogen oxides sensor ·
No. 2 nitrogen oxides sensor ·
Urea solution ·
Urea injector set ·
No. 2 exhaust pipe converter assembly (SCR catalyst) |
Class B1 | DTC stored |
The urea injector control feeds back urea solution dose if a measured NOx purification rate deviates from an estimated NOx purification rate.
The nitrogen oxides sensor measures NOx level and also counts NH3 as NOx.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P2BAE | After warming up engine, idle engine for within 10 seconds. |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Measure urea solution concentration.
30 to 35%
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the connector connection for the ambient air temperature sensor (cooler thermistor) connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the installation of the ambient air temperature sensor (cooler thermistor).
Make sure there is no dirt, damage or clogging in the sensing unit of the ambient air temperature sensor (cooler thermistor).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ambient air temperature sensor (cooler thermistor).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the connector connection for the mass air flow meter connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the installation of the mass air flow meter.
Make sure there is no dirt, damage or clogging in the sensing unit of the mass air flow meter.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the urea solution pipe (pressure line) and check if there are no disconnections, clogging, corrosion, or cracks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Prepare a beaker or similar, plus a larger measuring vessel for measuring the urea solution to be injected, before perform this inspection.
(If the vessel is small, there is dispersion at the time of injection from the injector, and the measuring quantity decreases.)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Data List / Reductant Level.
Check the value of "Reductant Level". If the value of the level is 11 L or less, refill the urea solution.
Remove the urea injector assembly from the front exhaust pipe assembly.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA INJECTOR>REMOVAL
Do not disconnect the urea injector assembly from the urea tube with heater assembly.
Use a cover, etc., to prevent foreign matter from entering the exhaust pipe.
Prepare a bucket or other receptacle for collecting urea solution from the urea injector assembly.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Reductant Injection / Pattern 3.
Perform "Pattern 3" and check the urea solution injection.
Urea solution injects from urea injector set.
When the urea solution tank temperature is -5°C (23°F) or lower, perform warm-up to raise it to 10°C (50°F) or higher.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 nitrogen oxides sensor and No. 2 nitrogen oxides sensor.
Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off for 30 seconds or more.
Perform the confirmation driving pattern.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read Current DTCs.
| Result | Proceed to |
|---|---|
| DTC P2BAE is output | A |
| DTCs are not output | B |
A
B
Turn the ignition switch off.
Replace urea solution injector with a new one. (Do not install)
Turn the ignition switch to ON.
Perform urea solution addition test as same as step 8.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Restore the original urea injector set and replace the urea solution pipe (pressure line).
| Proceed to |
|---|
| NEXT |
NEXT
Replace the urea solution pipe.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the mass air flow meter.
Clean the sensing unit and install it properly.
If damaged, replace the mass air flow meter.
| Proceed to |
|---|
| NEXT |
NEXT
Connect securely the mass air flow meter connector.
Repair it as needed.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ambient air temperature sensor (cooler thermistor).
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the ambient air temperature sensor (cooler thermistor).
Clean the sensing unit and install it properly.
If damaged, replace the ambient air temperature sensor (cooler thermistor).
| Proceed to |
|---|
| NEXT |
NEXT
Connect securely the ambient air temperature sensor (cooler thermistor) connector.
Repair it as needed.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the urea solution (AdBlue)
If the urea solution concentration is below the standard, drain the urea solution through the tank drain with the ignition switch ON, and then refill the tank with at least 5 liters of urea solution.
Afterward, drive the vehicle and check if the problem does not recur under driving conditions.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off for 30 seconds or more.
Perform the confirmation driving pattern.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT