Home › Engine / Hybrid System › N04C-VL (ENGINE MECHANICAL) › CAMSHAFT › from 2019.08
RM2850E _51 Engine / Hybrid System _073160 N04C-VL ENGINE MECHANICAL _0356002 CAMSHAFT A

N04C-VL ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 16400 1.REMOVE RADIATOR ASSEMBLY

Hide 17201 2.REMOVE TURBOCHARGER SUB-ASSEMBLY

Hide 23670 3.REMOVE INJECTOR ASSEMBLY

Hide 22100 4.REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY

Hide 87246B 6.DISCONNECT OUTLET HEATER WATER HOSE B

Hide 87245B 7.DISCONNECT INLET HEATER WATER HOSE B

Hide 87208L 8.REMOVE WATER PIPE SUB-ASSEMBLY

Hide 16206B 9.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16206 10.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 88320 11.SEPARATE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 88431 12.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

Hide 16630G 13.REMOVE IDLER PULLEY ASSEMBLY

Hide 88420 14.REMOVE IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)

Hide 16100 15.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 27020 16.REMOVE GENERATOR ASSEMBLY

Hide 29601B 19.REMOVE VACUUM PUMP OIL PIPE SUB-ASSEMBLY

Hide 29300 20.REMOVE VACUUM PUMP ASSEMBLY

Hide 12204 21.REMOVE VENTILATION VALVE SUB-ASSEMBLY

Hide 16206A 22.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 13901 23.REMOVE NO. 1 VALVE ROCKER SHAFT SUB-ASSEMBLY

Hide 11101 26.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 27.REMOVE CYLINDER HEAD GASKET

a.

Remove the cylinder head gasket.


Hide 13470 29.REMOVE CRANKSHAFT PULLEY ASSEMBLY

a.
A151470

Using a 46 mm socket wrench, remove the nut, crankshaft pulley spacer and crankshaft pulley.

HINT:

Insert a screwdriver through the inspection hole of the flywheel housing into the ring gear of the flywheel to keep it from turning together with the crankshaft.



Hide 11351H 30.REMOVE FLYWHEEL HOUSING STAY RH

a.

Remove the 4 bolts and the flywheel housing stay RH.


Hide 11351G 31.REMOVE FLYWHEEL HOUSING STAY LH

a.

Remove the 4 bolts and the flywheel housing stay LH.


Hide 12101 32.REMOVE OIL PAN SUB-ASSEMBLY

a.
A000019

Remove the 26 bolts from the oil pan sub-assembly.


b.

Insert the blade of an oil pan seal cutter between the cylinder block and oil pan sub-assembly. Cut through the applied sealer and remove the oil pan sub-assembly.

NOTICE:

Do not damage the contact surface of the cylinder block and oil pan sub-assembly.



Hide 11321C 33.REMOVE TIMING GEAR COVER

a.
A448657

Remove the 15 bolts.


b.

Using a screwdriver with its tip wrapped in protective tape, pry out the timing gear cover.

NOTICE:

Do not damage the contact surfaces of the timing gear cover and cylinder block sub-assembly.



Hide 11301C 34.REMOVE TIMING CHAIN OR BELT COVER OIL SEAL

a.
A448635C04
0.313,0.313 0.563,0.313 0.563,0.313 1.021,0.771 true 2.5,1.771 3.031,1.771 false 2.781,1.76 2.781,1.323 false 0.115,0.219 0.427,0.375 0.313,0.156 10 false *a 3.073,1.708 3.385,1.865 0.313,0.156 10 false *b
*a Protective Tape
*b Wooden Block


Using a screwdriver with its tip wrapped in protective tape, pry out the timing chain or belt cover oil seal.

HINT:

Use wooden blocks and a piece of cloth to prevent the contact surfaces and the timing gear cover from being damaged.



Hide 13501 35.REMOVE CAMSHAFT

a.
A146589

Remove the 2 bolts and the camshaft.