The injection or supply pump assembly is a single-type pump and has a circuit for fuel suction that achieves high pressure force feed and reduction of driving torque, and for force feed process. The ECM controls the suction control valve, which operates fuel suction by the plunger in the process of suction.
When the internal fuel pressure of the common rail assembly exceeds the target pressure, the pressure limiter on the common rail assembly starts operating to control the internal fuel pressure of the common rail assembly.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0088 | Conditions (a) and (b) are met 150 times or more (1 trip detection logic):
(a) Ignition switch ON (b) Internal fuel pressure of the common rail: 250 MPa (2549 kgf/cm2, 36259 psi) or more |
·
Injection or supply pump assembly (suction control valve) ·
Open or short in suction control valve circuit ·
Common rail assembly ·
ECM |
| P0627 | Open or short in suction control valve circuit for more than 0.5 seconds (1 trip detection logic) | ·
Injection or supply pump assembly (suction control valve) ·
Open or short in suction control valve circuit ·
Common rail assembly ·
ECM |
| P1229 | Fuel over-feed (1 trip detection logic):
The actual fuel pressure exceeds the target fuel pressure by 40000 kPa or higher for 10 seconds |
·
Injection or supply pump assembly (suction control valve) ·
Open or short in suction control valve circuit ·
Common rail assembly ·
ECM |
Refer to DTC P0087 (Click here Engine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0087).
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
After replacing the injection or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Rear the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0087, P0180, P0182, P0183, P0190, P0191, P0192, P0193, P0201, P0202, P0203, P0204 or P062D is not output | A |
| DTC P0087, P0180, P0182, P0183, P0190, P0191, P0192, P0193, P0201, P0202, P0203, P0204 or P062D is output | B |
A
B
Inspect the injection or supply pump assembly (suction control valve) (Click hereEngine / Hybrid System>N04C-VQ (FUEL)>FUEL SUPPLY PUMP>INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0088 and/or P1229 are output | A |
| DTC P0627 is output | B |
A
B
Disconnect the suction control valve connector and then start the engine.
Engine does not start.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current.
Read the value.
| Engine Speed | Result |
|---|---|
| Idling | 1350 to 2200 mA |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.
Read the Value.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Fuel Press | Idling | 20000 to 30000 kPa |
| 3000 rpm without Load | 130000 to 150000 kPa | |
| Target Common Rail Pressure | Idling | Deviation from Fuel Press within 5000 kPa |
| 3000 rpm without Load | Deviation from Fuel Press within 5000 kPa |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the ECM connector.
Disconnect the fuel pressure sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B105-16 (PCR1) - B93-2 (PCR1) | Always | Below 1 Ω |
| B104-13 (VC) - B93-1 (VC1) | Always | Below 1 Ω |
| B104-14 (E2) - B93-3 (E1) | Always | Below 1 Ω |
| B105-2 (PCR2) - B93-5 (PCR2) | Always | Below 1 Ω |
| B105-13 (VC2) - B93-6 (VC2) | Always | Below 1 Ω |
| B105-14 (E21) - B93-4 (E2) | Always | Below 1 Ω |
| B105-16 (PCR1) or B93-2 (PCR1) - Body ground | Always | 10 kΩ or higher |
| B104-13 (VC) or B93-1 (VC1) - Body ground | Always | 10 kΩ or higher |
| B105-2 (PCR2) or B93-5 (PCR2) - Body ground | Always | 10 kΩ or higher |
| B105-13 (VC2) or B93-6 (VC2) - Body ground | Always | 10 kΩ or higher |
| B104-14 (E2) or B93-3 (E1) - Other terminals | Always | 10 kΩ or higher |
| B105-14 (E21) or B93-4 (E2) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
Wiggle the fuel pressure sensor connector and check that the fuel pressure reading does not change.
The fuel pressure reading does not change.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B103-23 (PCV+) - B52-1 (SCV+) | Always | Below 1 Ω |
| B103-12 (PCV-) - B52-2 (SCV-) | Always | Below 1 Ω |
| B103-23 (PCV+) or B52-1 (SCV+) - Body ground | Always | 10 kΩ or higher |
| B103-12 (PCV-) or B52-2 (SCV-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
While cranking or idling the engine, check the waveform of the ECM connector using an oscilloscope.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| B103-23 (PCV+) - B102-1 (E1) | Idling or cranking with warm engine | 10 V/DIV., 5 ms./ DIV. | Correct waveform appears as shown |
| B103-12 (PCV-) - B102-1 (E1) | Idling or cranking with warm engine | 1 V/DIV., 5 ms./ DIV. | Correct waveform appears as shown |
| *a | Component with harness connected
(ECM) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0088, P0627 or P1229 is output | A |
| DTC is not output | B |
A
B
Inspect the fuel injection system circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>Fuel Injection System).
Check whether the malfunction has been repairedsuccessfully.
Malfunction has been repaired successfully.
| Proceed to |
|---|
| OK |
| NG |
OK
NG