Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for RHD vehicles.
55301
1.INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
Install the 2 nuts <A>, 2 bolts <B> and 8 bolts <C> and instrument panel sub-assembly.
Install the 2 clips <H>.
Connect the 5 connectors.
w/ Outer Mirror Switch:
Attach the clamp.
w/ Antenna:
Connect the connector and attach the clamp.
Connect the connector and attach the 4 clamps.
| *A | w/ Outer Mirror Switch | *B | w/ Antenna |
w/o Passenger Side Airbag:
Install the 2 bolts <G>.
20 N*m (204 kgf*cm, 15 ft.*lbf)
45286B
2.INSTALL UPPER STEERING COLUMN COVER
45287
3.INSTALL LOWER STEERING COLUMN COVER
45100
4.INSTALL STEERING WHEEL ASSEMBLY
45130
5.INSTALL HORN BUTTON ASSEMBLY
55962A
6.INSTALL SIDE DEFROSTER NOZZLE LH (w/ Heater)
Attach the 4 claws to install the side defroster nozzle LH.
55969
7.INSTALL NO. 2 DEFROSTER NOZZLE OPENING COVER (w/o Heater)
Attach the 4 claws to install the No. 2 defroster nozzle opening cover.
73970A
8.INSTALL INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (w/ Passenger Side Airbag)
55523
9.INSTALL HEATER CONTROL OPENING COVER (w/o Air Control Panel)
Install the heater control opening cover with the 4 bolts <C>.
55900
10.INSTALL AIR CONDITIONING CONTROL ASSEMBLY (w/ Air Control Panel)
55522B
11.INSTALL RADIO TUNER OPENING COVER (w/o Audio)
Install the radio tuner opening cover with the 4 bolts.
86120
12.INSTALL RADIO RECEIVER ASSEMBLY (w/ Audio)
83100
13.INSTALL COMBINATION METER ASSEMBLY
55410C
14.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Connect the connector.
Attach the first claw.
Attach the 24 claws to install the instrument cluster finish panel assembly.
| *a | First Claw | - | - |
55432C
15.INSTALL RESERVOIR TANK DOOR
Attach the 4 clips to install the reservoir tank door.
55961A
16.INSTALL SIDE DEFROSTER NOZZLE RH (w/ Heater)
Attach the 3 claws to install the side defroster nozzle RH.
55959A
17.INSTALL NO. 1 DEFROSTER NOZZLE OPENING COVER (w/o Heater)
Attach the 3 claws to install the No. 1 defroster nozzle opening cover.
55458B
18.INSTALL LOWER INSTRUMENT COVER
Attach the 3 claws to install the lower instrument cover.
83210
19.INSTALL TACHOGRAPH ASSEMBLY (w/ Tachograph)
55601C
20.INSTALL INSTRUMENT PANEL UNDER TRAY SUB-ASSEMBLY
Attach the clamp and connect the connector.
w/ Tachograph:
Connect the connector.
Attach the 4 claws to install the instrument panel under tray sub-assembly with the 2 screws <D> and 2 screws.
w/o Tachograph:
Attach the 4 claws to install the instrument panel under tray sub-assembly with the 4 screws <D>.
55470
21.INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY
Connect each connector.
Insert the first claw and then attach the 9 claws in the order shown in the illustration.
| *a | First Claw |
Attach the 17 claws and 4 guides indicated by the arrow in the order shown in the illustration to install the instrument cluster finish panel garnish assembly.
55480D
22.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
for LHD, w/ Fuel lid opener:
Attach the 3 claws to connect the fuel lid lock control cable assembly.
Connect each connector.
Attach the 7 claws to install the lower instrument panel finish panel assembly.
Install the bolt <B>.
55845B
23.INSTALL REAR NO. 3 HEATER TO REGISTER DUCT (w/ Heater)
Install the rear No. 3 heater to register duct with the 2 clips.
55521C
24.INSTALL STEREO OPENING COVER (w/o Microphone)
Install the stereo opening cover with the 2 screws.
86290A
25.INSTALL MICROPHONE AMPLIFIER ASSEMBLY (w/ Microphone)
55412D
26.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL
w/ Outer Mirror Control Switch:
Attach the 2 clamps and connect the connector.
Attach the 3 guides and 9 claws to install the center instrument cluster finish panel.
86250
27.INSTALL AMPLIFIER MICROPHONE ASSEMBLY (w/ Microphone)
55433B
28.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
Attach the 15 claws to install the lower No. 2 instrument panel finish panel.
58841A
29.INSTALL SHIFTING HOLE COVER (for Automatic Transmission)
58848A
30.INSTALL SHIFT LEVER HOLE COVER (for Manual Transmission)
33555D
31.INSTALL SHIFT LEVER BOOT (for Manual Transmission)
58534A
32.INSTALL TRANSMISSION COVER MAT (for Manual Transmission)
33504F
33.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)
Gently rotate the shift lever knob sub-assembly by hand until it locks.
After locking, further tighten by 1.5 turns.
After tightening, rotate and adjust the tightened direction so that the shift pattern is positioned within +/-10° of the front of the vehicle.
62211
34.INSTALL FRONT PILLAR GARNISH RH
62212
35.INSTALL FRONT PILLAR GARNISH LH
Use the same procedure described for the RH side.
62311C
36.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Connect the front door opening trim weatherstrip RH.
Click hereVehicle Interior>INTERIOR>ROOF HEADLINING>INSTALLATION
74603
37.INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY
74617V
38.INSTALL ASSIST GRIP PLUG
39.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
40.CHECK SRS WARNING LIGHT
for 2 Connector Type:
for 3 Connector Type: