Home › Engine / Hybrid System › N04C-UH (FUEL) › COMMON RAIL › from 2021.01
RM2850E _51 Engine / Hybrid System _073175 N04C-UH FUEL _0356084 COMMON RAIL A

N04C-UH FUEL  COMMON RAIL  INSTALLATION  


PROCEDURE

Hide 1.INSTALL COMMON RAIL ASSEMBLY

a.

Install the common rail assembly with the 2 bolts.

Torque:

55 N*m (561 kgf*cm, 41 ft.*lbf)



b.

Connect the fuel hose.


c.

Connect the fuel pressure sensor connector.


Hide 2.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE

a.

Temporarily install the fuel filter to injection pump fuel pipe with the 2 union nuts.


b.

Using a union nut wrench (17 mm), tighten the union nuts.

Torque:

35 N*m (357 kgf*cm, 26 ft.*lbf)


NOTICE:
·

If the supply pump assembly has been replaced, the fuel filter to injection pump fuel pipe must also be replaced.

·

Refer to the torque above when not using the union nut wrench. When using the union nut wrench, calculate the torque in accordance with the lengths of the union nut wrench and torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




c.

Install the pipe clamp with the nut. Tighten the nut until the clamp's edges make contact with the engine side clamp's edges.


Hide 3.INSTALL INJECTION PIPE SUB-ASSEMBLY

a.

Temporarily install the 4 injection pipe sub-assemblies with the union nuts.


b.

Using a union nut wrench (17 mm), tighten the 8 union nuts.

Torque:

35 N*m (357 kgf*cm, 26 ft.*lbf)


NOTICE:
·

If the common rail has been replaced, the injection pipe sub-assemblies must also be replaced.

·

Refer to the torque above when not using the union nut wrench. When using the union nut wrench, calculate the torque in accordance with the lengths of the union nut wrench and torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




Hide 4.INSTALL INJECTION PIPE CLAMP

a.

Install the 2 injection pipe clamps with the 2 nuts. Tighten the nut until the clamp's edges make contact with the engine side clamp's edges.


Hide 5.INSTALL NO. 2 HARNESS BRACKET

a.

Install the No. 2 harness bracket with the 2 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



b.

Engage the 3 harness clamps.


Hide 6.INSTALL NO. 2 INTAKE PIPE WITH EGR VALVE

Hide 16206 7.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 17113 8.INSTALL INTAKE PIPE WITH VENTURI ASSEMBLY

Hide 15301 9.INSTALL OIL DIPSTICK GUIDE

Hide 44360 11.INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 25625B 12.INSTALL EGR VALVE BRACKET

Hide 13.INSTALL WIRE HARNESS AND CONNECTORS

Hide 25608 14.INSTALL EGR COOLER SUB-ASSEMBLY

Hide 17271 15.INSTALL NO. 1 TURBO INSULATOR

Hide 16206C 17.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 58701A 19.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY

Hide 33504F 20.INSTALL SHIFT LEVER SUB-ASSEMBLY

Hide 33820B 21.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 22.BLEED AIR FROM FUEL SYSTEM

Hide 33531B 26.INSTALL SHIFT AND SELECT LEVER SHAFT DUST BOOT

Hide 58534A 27.INSTALL TRANSMISSION COVER MAT

Hide 58420 28.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 58521D 29.INSTALL ENGINE SERVICE HOLE COVER MAT

Hide 58734B 30.INSTALL ENGINE SERVICE COVER REAR WEATHERSTRIP

Hide 58410 31.INSTALL ENGINE SERVICE HOLE COVER

Hide 51441D 32.INSTALL NO. 1 ENGINE UNDER COVER (for Plastic Type)

Hide 51441D 33.INSTALL NO. 1 ENGINE UNDER COVER (for Metal Type)

Hide 51459 34.INSTALL ENGINE SIDE COVER STAY (for TCAP Made)