Refer to DTC P0037 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0037).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0136
P0156 |
Abnormal voltage output:
During active air fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic): (a)
Heated oxygen sensor voltage does not decrease to less than 0.21 V (b)
Heated oxygen sensor voltage does not increase to 0.6 V or higher |
·
Heated oxygen sensor (bank 1, 2 sensor 2) circuit ·
Heated oxygen sensor (bank 1, 2 sensor 2) ·
Air fuel ratio sensor (bank 1, 2 sensor 1) ·
Gas leak from exhaust system ·
Fuel pressure ·
Fuel injector assembly ·
PCV valve and hose ·
Intake system |
| P0137
P0157 |
Low voltage (open):
During active air fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic): (a)
Heated oxygen sensor voltage output less than 0.21 V (b)
Target air fuel ratio rich |
·
Heated oxygen sensor (bank 1, 2 sensor 2) circuit ·
Heated oxygen sensor (bank 1, 2 sensor 2) ·
Air fuel ratio sensor (bank 1, 2 sensor 1) ·
Gas leak from exhaust system |
| P0138
P0158 |
High voltage (short):
During active air fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic): (a)
Heated oxygen sensor voltage output higher than 0.6 V (b)
Target air fuel ratio lean |
·
Heated oxygen sensor (bank 1, 2 sensor 2) circuit ·
Heated oxygen sensor (bank 1, 2 sensor 2) ·
Air fuel ratio sensor (bank 1, 2 sensor 1) ·
ECM |
This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.
Performing this confirmation driving pattern will activate the heated oxygen sensor monitor (the catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the tester on [A].
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
With the shift lever in D, drive the vehicle at 60 to 100 km/h (37 to 62 mph) for 10 minutes or more [C].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine / DTC [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0136, P0137, P0138, P0156, P0157 or P0158.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again.
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the intelligent tester.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
| Tester Display
(Sensor) |
Injection Volume | Status | Voltage |
|---|---|---|---|
| AFS Voltage B1S1
AFS Voltage B2S1 (Air fuel ratio) |
12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2
O2S B2S2 (Heated oxygen) |
12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
|---|---|---|---|
| 1 |
0.135,0.302 1.719,0.76
1.583,0.458
10
false
Injection Volume
1.375,0.75 2.26,1.083
0.885,0.333
10
false
12.5%
1.333,1.167 2.219,1.5
0.885,0.333
10
false
-12.5%
2.896,0.969 3.427,1.25
0.531,0.281
10
false
OK
0.948,1.167 2.021,1.5
1.073,0.333
10
false
Below 3.1 V
0.625,0.792 2.115,1.167
1.49,0.375
10
false
Higher than 3.4 V
0.156,0.24 1.438,0.635
1.281,0.396
10
false
Output Voltage
|
0.135,0.302 1.719,0.76
1.583,0.458
10
false
Injection Volume
1.375,0.75 2.26,1.083
0.885,0.333
10
false
12.5%
1.333,1.167 2.219,1.5
0.885,0.333
10
false
-12.5%
0.583,0.76 2.042,1.198
1.458,0.438
10
false
Higher than 0.55 V
0.969,1.135 1.938,1.448
0.969,0.313
10
false
Below 0.4 V
0.208,0.271 1.635,0.677
1.427,0.406
10
false
Output Voltage
2.896,0.948 3.427,1.26
0.531,0.313
10
false
OK
|
- |
| 2 |
0.135,0.302 1.719,0.76
1.583,0.458
10
false
Injection Volume
1.375,0.75 2.26,1.083
0.885,0.333
10
false
12.5%
1.333,1.167 2.219,1.5
0.885,0.333
10
false
-12.5%
2.875,1.052 3.427,1.333
0.552,0.281
10
false
NG
0.51,1.156 1.823,1.521
1.313,0.365
10
false
Almost no reaction
0.354,0.469 1.49,0.906
1.135,0.438
10
false
Output Voltage
|
0.135,0.302 1.719,0.76
1.583,0.458
10
false
Injection Volume
1.375,0.75 2.26,1.083
0.885,0.333
10
false
12.5%
1.333,1.167 2.219,1.5
0.885,0.333
10
false
-12.5%
0.583,0.76 2.042,1.198
1.458,0.438
10
false
Higher than 0.55 V
0.969,1.135 1.938,1.448
0.969,0.313
10
false
Below 0.4 V
0.208,0.271 1.635,0.677
1.427,0.406
10
false
Output Voltage
2.896,0.948 3.427,1.26
0.531,0.313
10
false
OK
|
·
Air fuel ratio sensor ·
Air fuel ratio sensor heater ·
Air fuel ratio sensor circuit |
| 3 |
0.135,0.302 1.719,0.76
1.583,0.458
10
false
Injection Volume
1.375,0.75 2.26,1.083
0.885,0.333
10
false
12.5%
1.333,1.167 2.219,1.5
0.885,0.333
10
false
-12.5%
2.896,0.969 3.427,1.25
0.531,0.281
10
false
OK
0.948,1.167 2.021,1.5
1.073,0.333
10
false
Below 3.1 V
0.625,0.792 2.115,1.167
1.49,0.375
10
false
Higher than 3.4 V
0.156,0.24 1.438,0.635
1.281,0.396
10
false
Output Voltage
|
0.135,0.302 1.719,0.76
1.583,0.458
10
false
Injection Volume
1.375,0.75 2.26,1.083
0.885,0.333
10
false
12.5%
1.333,1.167 2.219,1.5
0.885,0.333
10
false
-12.5%
2.875,1.052 3.427,1.333
0.552,0.281
10
false
NG
0.51,1.156 1.823,1.521
1.313,0.365
10
false
Almost no reaction
0.354,0.469 1.49,0.906
1.135,0.438
10
false
Output Voltage
|
·
Heated oxygen sensor ·
Heated oxygen sensor heater ·
Heated oxygen sensor circuit |
| 4 |
0.135,0.302 1.719,0.76
1.583,0.458
10
false
Injection Volume
1.375,0.75 2.26,1.083
0.885,0.333
10
false
12.5%
1.333,1.167 2.219,1.5
0.885,0.333
10
false
-12.5%
2.875,1.052 3.427,1.333
0.552,0.281
10
false
NG
0.51,1.156 1.823,1.521
1.313,0.365
10
false
Almost no reaction
0.354,0.469 1.49,0.906
1.135,0.438
10
false
Output Voltage
|
0.135,0.302 1.719,0.76
1.583,0.458
10
false
Injection Volume
1.375,0.75 2.26,1.083
0.885,0.333
10
false
12.5%
1.333,1.167 2.219,1.5
0.885,0.333
10
false
-12.5%
2.875,1.052 3.427,1.333
0.552,0.281
10
false
NG
0.51,1.156 1.823,1.521
1.313,0.365
10
false
Almost no reaction
0.354,0.469 1.49,0.906
1.135,0.438
10
false
Output Voltage
|
·
Fuel injector assembly ·
Fuel pressure ·
Gas leak from exhaust system (Air fuel ratio extremely rich or lean) |
Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.
To display the graph, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2; then press the view button.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0138 or P0158 is output | A |
| DTC P0137 or P0157 is output | B |
| DTC P0136 or P0156 is output | C |
| DTC P0136, P0137, P0138, P0156, P0157 or P0158 and other DTCs are output | D |
If any DTCs other than P0136, P0137, P0138, P0156, P0157 and P0158 are output, troubleshoot those DTCs first.
A
B
C
D
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / O2S B1S2 or O2S B2S2.
Allow the engine to idle.
Read the heated oxygen sensor output voltage while idling.
| Heated Oxygen Sensor Output Voltage | Proceed to |
|---|---|
| 1.0 V or higher | A |
| Less than 1.0 V | B |
A
B
Disconnect the heated oxygen sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (+B) - 3 (E2) | Always | 10 kΩ or higher |
| 1 (+B) - 4 (OX1B) | Always | 10 kΩ or higher |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX2B) | Always | 10 kΩ or higher |
OK
NG
Turn the engine switch to off and wait for 5 minutes or more.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D1-48 (HT1B) - D1-88 (OX1B) | Always | 10 kΩ or higher |
| D1-47 (HT2B) - D1-87 (OX2B) | Always | 10 kΩ or higher |
OK
NG
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the tester.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
The air fuel ratio sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2, on the tester.
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
| Tester Display
(Sensor) |
Voltage Variation | Proceed to |
|---|---|---|
| AFS Voltage B1S1
AFS Voltage B2S1 (Air fuel ratio) |
Alternates between higher and less than 3.3 V | OK |
| Remains at higher than 3.3 V | NG | |
| Remains at less than 3.3 V | NG |
A normal heated oxygen sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage (AFS Voltage B1S1 or AFS Voltage B2S1) remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.
OK
NG
This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut operation. When the sensor is normal, the sensor current will indicate less than 2.2 mA in this test.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Drive the vehicle by the driving pattern as listed below:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Warm up the engine until the engine coolant temperature reaches 75°C (167°F) or higher.
Drive the vehicle at 60 km/h (37 mph) or more for 10 minutes or more.
Stop the vehicle.
Accelerate the vehicle to 60 km/h (37 mph) or more and decelerate for 5 seconds or more. Perform this 3 times.
Enter the following menus: Powertrain / Engine / Data List / All Data / AFS Current B1S1 and AFS Current B2S1.
Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.
Less than 2.2 mA
To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.
If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the tester.
OK
NG
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / O2S B1S2 or O2S B2S2.
Change the fuel injection volume using the tester, monitoring the voltage output of the heated oxygen sensors displayed on the tester.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
The heated oxygen sensor has a maximum output delay of approximately 20 seconds.
Fluctuates between 0.4 V or less and 0.55 V or higher.
OK
NG
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
Change the fuel injection volume using the tester, and monitor the voltage output of air fuel ratio and heated oxygen sensors displayed on the tester.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
The air fuel ratio sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2, on the tester.
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
| Tester Display (Sensor) | Voltage Variation | Proceed to |
|---|---|---|
| AFS Voltage B1S1
AFS Voltage B2S1 (Air fuel ratio) |
Alternates between higher and less than 3.3 V | OK |
| Remains at higher than 3.3 V | NG | |
| Remains at less than 3.3 V | NG |
A normal heated oxygen sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage (AFS Voltage B1S1 or AFS Voltage B2S1) remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.
OK
NG
Check for exhaust gas leaks.
No gas leaks.
OK
NG
Inspect the heated oxygen sensor (See page Engine / Hybrid System>2GR-FE EMISSION CONTROL>HEATED OXYGEN SENSOR>INSPECTION).
OK
NG
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G53-2 (HT1B) - D1-48 (HT1B) | Always | Below 1 Ω |
| G53-4 (OX1B) - D1-88 (OX1B) | Always | Below 1 Ω |
| G53-3 (E2) - D1-65 (EX1B) | Always | Below 1 Ω |
| D39-1 (HT2B) - D1-47 (HT2B) | Always | Below 1 Ω |
| D39-3 (OX2B) - D1-87 (OX2B) | Always | Below 1 Ω |
| D39-4 (E2) - D1-64 (EX2B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G53-2 (HT1B) or D1-48 (HT1B) - Body ground | Always | 10 kΩ or higher |
| G53-4 (OX1B) or D1-88 (OX1B) - Body ground | Always | 10 kΩ or higher |
| D39-1 (HT2B) or D1-47 (HT2B) - Body ground | Always | 10 kΩ or higher |
| D39-3 (OX2B) or D1-87 (OX2B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the heated oxygen sensor (See page Engine / Hybrid System>2GR-FE EMISSION CONTROL>HEATED OXYGEN SENSOR>REMOVAL).
NEXT
Perform Confirmation Driving Pattern.
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0136, P0137, P0138, P0156, P0157 or P0158.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.
| Result | Proceed to |
|---|---|
| ABNORMAL
(DTC P0136, P0137, P0138, P0156, P0157 or P0158 is output) |
A |
| NORMAL
(DTC is not output) |
B |
A
B
Replace the air fuel ratio sensor (See page Engine / Hybrid System>2GR-FE EMISSION CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).
NEXT
Perform Confirmation Driving Pattern.
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0136, P0138, P0156 or P0158.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.
| Result | Proceed to |
|---|---|
| ABNORMAL
(DTC P0136, P0138, P0156 or P0158 is output) |
A |
| NORMAL
(DTC is not output) |
B |
A
B