Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2014.09
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0016  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)  P0017  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)  P0018  Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)  P0019  Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)  


DESCRIPTION

In the VVT system, the appropriate intake and exhaust valve open and close timings are controlled by the ECM. The ECM performs intake and exhaust valve control by performing the following: 1) controlling the camshaft (intake and exhaust) and camshaft timing oil control valve assembly (intake and exhaust), and operating the camshaft timing gear assembly or camshaft timing exhaust gear assembly; and 2) changing the relative positions of the gaps between the camshaft and crankshaft.

DTC No. DTC Detection Condition Trouble Area
P0016 Deviation in crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 1) signal (2 trip detection logic)
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft of bank1, 2)

·

Oil control valve filter (RH, LH)

·

Oil pipe

·

Camshaft timing gear assembly (bank 1, 2)

·

ECM


P0017 Deviation in crankshaft position sensor signal and VVT sensor (for exhaust camshaft of bank 1) signal (2 trip detection logic)
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust camshaft of bank1, 2)

·

Oil control valve filter (RH, LH)

·

Oil pipe

·

Camshaft timing exhaust gear assembly (bank 1, 2)

·

ECM


P0018 Deviation in crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 2) signal (2 trip detection logic)
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft of bank1, 2)

·

Oil control valve filter (RH, LH)

·

Oil pipe

·

Camshaft timing gear assembly (bank 1, 2)

·

ECM


P0019 Deviation in crankshaft position sensor signal and VVT sensor (for exhaust camshaft of bank 2) signal (2 trip detection logic)
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust camshaft of bank1, 2)

·

Oil control valve filter (RH, LH)

·

Oil pipe

·

Camshaft timing exhaust gear assembly (bank 1, 2)

·

ECM



CAUTION / NOTICE / HINT

HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016, P0017, P0018 OR P0019)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs.

Result
Result Proceed to
P0016, P0017, P0018 or P0019 is output A
P0016, P0017, P0018 or P0019 and other DTCs are output B

HINT:

If any DTCs other than P0016, P0017, P0018 or P0019 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the A/C switch on.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Linear (Bank 1), Control the VVT Linear (Bank 2), Control the VVT Exhaust Linear (Bank 1) or Control the Exhaust VVT Linear (Bank 2) / All Data / VVT Change Angle #1, VVT Change Angle #2, VVT Ex Chg Angle #1, VVT Ex Chg Angle #2.


f.

Perform the Active Test. Check that the displacement angle varies.

OK:

Displacement angle varies.




OK

3.ADJUST VALVE TIMING

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT)
3.ADJUST VALVE TIMING

NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016, P0017, P0018 OR P0019)
4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT)
a.

Inspect the camshaft timing oil control valve assembly (for intake or exhaust camshaft) (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

5.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT)

5.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE

OK

6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

REPLACE OIL CONTROL VALVE FILTER OR OIL PIPE

6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
a.

Inspect the camshaft timing gear assembly or camshaft timing exhaust gear assembly (See page Engine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY).



OK

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016, P0017, P0018 OR P0019)

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016, P0017, P0018 OR P0019)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Clear the DTCs.


e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the tester on.


h.

Start the engine and warm it up.


i.

Idle the engine for 5 minutes or more.


j.

Drive the vehicle for 2 to 3 minutes.


k.

Enter the following menus: Powertrain / Engine / DTC / Pending.


l.

Read the pending DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0016, P0017, P0018 or P0019 is output B



A

END

B