Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P0051  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)  P0052  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)  P101D  A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON  P103D  A/F Sensor Heater Circuit Performance Bank 2 Sensor 1 Stuck ON  


DESCRIPTION

HINT:

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.


The air fuel ratio sensor generates voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection time.

If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is a planar type and integrated with a heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), current flows to the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through alumina, therefore sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A234900E52
1.594,3 1.146,2.438 true 1.813,3.104 2.219,2.531 true 2.927,1.875 3.323,1.26 true 3.063,1.927 3.521,1.604 true 3.188,2.219 3.625,2.031 true 2.823,2.26 3.604,2.448 true 2.99,2.458 3.615,2.458 true 3.052,2.573 3.552,2.875 true 0.594,2.323 1.667,2.521 1.073,0.198 10 false Element 2.094,2.333 3.167,2.531 1.073,0.198 10 false Cover 0.198,3.302 1.271,3.5 1.073,0.198 10 false Exhaust Gas 1.125,3.458 1.438,3.635 0.313,0.177 10 false A 2,3.469 2.313,3.646 0.313,0.177 10 false A 3.26,0.844 4.74,1.208 1.479,0.365 10 false Solid Electrolyte (Zirconia Element) 3.604,1.5 5.01,1.708 1.406,0.208 10 false Alumina 3.698,1.917 5.104,2.125 1.406,0.208 10 false Heater 3.677,2.385 5.083,2.594 1.406,0.208 10 false Platinum Electrode 2.438,3.219 3.844,3.427 1.406,0.208 10 false A-A Cross Section 3.615,2.823 5.021,3.031 1.406,0.208 10 false Atmospheric Air 5.073,0.656 6.958,1.042 1.885,0.385 10 false ECM Monitored Air Fuel Ratio Sensor Voltage 5.708,3.156 6.906,3.354 1.198,0.198 10 false Air Fuel Ratio

HINT:
·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the engine switch is turned off.

·

The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

A159612E06
0.103,0.065 3.390,0.221 3.288,0.156 10 Reference (System Diagram of Bank 1 Sensor 1): 0.35,0.869 1.323,1.299 0.973,0.429 10 from A/F Fuse 0.518,2.458 1.300,2.772 0.782,0.313 10 from EFI MAIN Relay 2.055,2.104 2.299,2.246 0.244,0.142 10 A/F 3.339,2.104 4.719,2.246 1.380,0.142 10 Air Fuel Ratio Sensor 3.423,0.79 3.621,0.960 0.198,0.170 10 +B 3.28,1.529 3.619,1.699 0.340,0.170 10 A1A- 4.433,0.79 4.816,0.960 0.383,0.170 10 HA1A 4.433,1.529 4.810,1.699 0.377,0.170 10 A1A+ 5.218,0.79 5.600,0.960 0.383,0.170 10 HA1A 5.218,1.529 5.595,1.699 0.377,0.170 10 A1A+ 5.218,2.391 5.595,2.561 0.377,0.170 10 A1A- 3.818,0.707 4.256,0.854 0.438,0.147 10 Heater 3.805,1.398 4.269,1.545 0.464,0.147 10 Sensor 5.903,3.453 6.239,3.602 0.336,0.149 10 ECM 6.309,1.543 6.778,1.859 0.468,0.316 10 Duty Control



DTC No. DTC Detection Condition Trouble Area
P0031
P0051
Air fuel ratio sensor heater current is less than 0.8 A (1 trip detection logic).
·

Open in air fuel ratio sensor (bank 1, 2 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

A/F relay

·

ECM


P0032
P0052
Air fuel ratio sensor heater current reaches the high limit
(1 trip detection logic).
·

Short in air fuel ratio sensor (bank 1, 2 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

A/F relay

·

ECM


P101D
P103D
Air fuel ratio sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
·

Short in air fuel ratio sensor (bank 1, 2 sensor 1) heater circuit

·

ECM



MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.

The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.

When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

CONFIRMATION DRIVING PATTERN

A342574E02
0.458,2.042 1.354,2.542 0.896,0.5 10 false Engine Switch on (IG) 0.969,1.792 1.865,2.292 0.896,0.5 10 false Idling 0.75,1.042 1.646,1.542 0.896,0.5 10 false 3000 rpm 1.896,2.167 2.792,2.667 0.896,0.5 10 false [A] 2.729,1.656 3.625,2.156 0.896,0.5 10 false [B] 4.042,0.896 4.938,1.396 0.896,0.5 10 false [C] 5.323,1.667 6.219,2.167 0.896,0.5 10 false [D] 5.958,3.052 6.854,3.552 0.896,0.5 10 false [E] 2.323,2.625 3.906,2.875 1.583,0.25 10 false 5 minutes or more 4.844,2.635 6.427,2.885 1.583,0.25 10 false 5 minutes or more 3.906,2.646 5.49,2.896 1.583,0.25 10 false 1 minute

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P0031, P0032, P0051, P0052, P101D or P103D.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the air fuel ratio sensor output voltage (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)
a.
U188229E02
2.135,0.865 1.823,1.188 false 0.479,1.021 0.75,1.198 0.271,0.177 10 false D42 0.531,1.542 0.729,1.719 0.198,0.177 10 false D8 2.156,0.74 2.427,0.938 0.271,0.198 10 false +B 0.875,1.51 1.094,1.688 0.219,0.177 10 false *2 0.271,0.115 0.531,0.365 0.26,0.25 10 false *a 0.865,0.99 1.073,1.188 0.208,0.198 10 false *1

Disconnect the air fuel ratio sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D42-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V
D8-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)
*1 Bank 1
*2 Bank 2



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - A/F RELAY)
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-86 (HA1A) - D42-1 (HA1A) Always Below 1 Ω
D1-109 (HA2A) - D8-1 (HA2A) Always Below 1 Ω
D1-86 (HA1A) or D42-1 (HA1A) - Body ground and other terminals Always 10 kΩ or higher
D1-109 (HA2A) or D8-1 (HA2A) - Body ground and other terminals Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032, P0051, P0052, P101D OR P103D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032, P0051, P0052, P101D OR P103D)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0031, P0032, P0051, P0052, P101D or P103D is output B



A

B

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - A/F RELAY)
a.

Disconnect the air fuel ratio sensor connector.


b.

Remove the A/F relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D42-2 (+B) - A/F relay terminal 3 Always Below 1 Ω
D8-2 (+B) - A/F relay terminal 3 Always Below 1 Ω
D42-2 (+B) or A/F relay terminal 3 - Body ground and other terminals Always 10 kΩ or higher
D8-2 (+B) or A/F relay terminal 3 - Body ground and other terminals Always 10 kΩ or higher




OK

6.INSPECT A/F RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT A/F RELAY
a.
A385864E01
0.23,0.566 0.330,0.722 0.100,0.156 10 3 1.513,0.565 1.627,0.731 0.114,0.166 10 5 0.223,1.353 0.330,1.513 0.107,0.159 10 1 1.516,1.357 1.622,1.519 0.106,0.163 10 2 2.531,0.486 2.585,0.732 false 2.579,0.732 2.654,0.732 false 2.674,0.639 2.775,0.795 0.100,0.156 10 3 2.531,1.148 2.581,0.926 false 2.576,0.926 2.65,0.926 false 2.684,0.854 2.798,1.020 0.114,0.166 10 5 2.215,1.47 2.401,1.34 false 2.397,1.34 2.441,1.34 false 2.461,1.247 2.567,1.410 0.106,0.163 10 2 2.862,1.47 2.725,1.575 false 2.73,1.575 2.693,1.575 false 2.599,1.491 2.706,1.650 0.107,0.159 10 1

Remove the A/F relay from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied to terminals 1 and 2 Below 1 Ω




OK

7.CHECK HARNESS AND CONNECTOR (A/F RELAY - BODY GROUND)

NG

REPLACE A/F RELAY

7.CHECK HARNESS AND CONNECTOR (A/F RELAY - BODY GROUND)
a.

Remove the A/F relay from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/F relay terminal 2 - Body ground Always Below 1 Ω




OK

8.CHECK HARNESS AND CONNECTOR (A/F RELAY - EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (A/F RELAY - EFI MAIN RELAY)
a.

Remove the A/F relay from the No. 1 engine room relay block.


b.

Remove the EFI MAIN relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/F relay terminal 1 - EFI MAIN relay terminal 3 Always Below 1 Ω
A/F relay terminal 1 or EFI MAIN relay terminal 3 - Body ground and other terminals Always 10 kΩ or higher




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (A/F RELAY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR